Search results

Shipping Firearms and Ammunition: UPS UPS rules state that if there's a pistol in the box, you're supposed to tell someone. Stop guessing and just read the regs.

A radar detector - even a V1 - is a tool, only as good as the operator. Just like one of those universal remotes or a BFH, if you don't know how to work it, there's no point in having it. If speed limits were set by the recommendations of professional traffic engineers (at the 85th...

I once went to court for speeding. The citation read the speed limit was 65 in that area, and my speed as claimed by the officer was 90. I was in a four cylinder Dodge Dakota. At court, the DA (or whatever professional position that lovely young lady occupied) spoke with me and with the...

I was in there earlier - excellent museum, with the small exception that the descriptions of the exhibits don't always match laterally with the exhibits. This is one of these - the rifle description is below and to the side of the rifle itself. Did you see the two MoH? And Jack Lucas's...

Something to try may be a coin - either a dime or a nickel. I can't say specifically if it'll work in your application, but it's worked in other rifles I've tried.

Break it in like this guydoes. Proper Barrel Break-in Procedure - YouTube No problems.

I've seen a Remington 700 223 that had a similar block at the rear of the magwell. Comparing that box to a standard short action it looked like the block was the only difference. As long as your bolt travels back far enough to clear that spacer, you shouldn't have any problems.

I've had the same happen with a xmark trigger - bottom line was the trigger was dirty after several hundred rounds and operating in blowing wind environments. Now I know about that particular failure mode, and The trigger gets cleaned along with the remainder of the rifle. It's the shooter's...

It's red loctite...remove with method of your choice.

Depends on the end quality desired. I cut a 10/22 barrel down using a cutoff wheel, cleaned it up with a file, and crowned it up with a countersink. It holds honest 1/2" 10 shot groups at 30 yards, and I'm okay with that. Would I take a cutoff wheel to a $350 bartlein blank? Nope. To cut down...

At that price, and having never fired it, I'd let it go. It was obviously a collector piece when you picked it up...let someone else sit on it for a while. Unless you have a big emotional attachment to it (family heirloom or the like) I don't see why you should have your money tied up in a...

I might consider a 40% markup on auto parts at a garage... If it was 40%. I had my truck in an alignment shop a week back as was told that I need a new balljoint at a cost of $122. Funny thing is, the Moog part that they'e quoting me is $52 at the local parts shop. i understand how business...

I think I saw him too!

Absolutely no different than taking a career 0311 with 20+ years' experience picking up that 9999 MOS and dropping him in the first open victor unit with a spot - just happened to be VMA-223. The 'wingers were used to the 10 hour days, five to six days a week to maintain a 500+ flight hour...

See! It's what I've been saying for years! All you need is krylon and SNIPER ammo - everything else is just fluff! ------ I don't care what anybody else does - unless I'm on a two-way range, I'm not dropping a $100 mag to the deck after I get done yank-firing $10 worth of ammo.

The shoe polish is oil based, so anything that will dilute oil should work just fine. I'd start with isopropyl alcohol (rubbing alcohol) before moving on to acetone (fingernail polish remover). Make sure to oil it back up before you reassemble, because you'll have a rust blob later if you...

I prefer Snap-On for the quality of their tools and in a business environment they're my first choice. At home, even though the quality is not the same, I'll go with Craftsman for two reasons - most times I can get two or three Craftsman widget turners for the price of the equivelant Snap-On...

Truly a fair enough question, and phrased as a question in lieu of an accusation. First inlking was the price, since the GAP rifle runs close to $4k and does not include the glass, which runs around $3k when one comes available. I contacted the 'seller' and immediately the story wasn't making...

How about this one for the bolt action guys. ARMSLIST - For Sale: MIL-SPEC GAP M40A1 USMC SNIPER RIFLE It's a no shit serious....scammer. Enjoy.

First off, drifting is not a sport. Just had to get that out. But that's not drifting either - that's just yanking the park brake to full while in traffic and at speed. Doesn't matter where or who you are - that's just driving like an asshole. (Or whatever that particular part translates to...