clone

  1. mhgray5

    SOLD 16" Lilja 223-8 M4 / NSW Recon barrel

    Used but not abused SEAL recon rifle barrel. 200 rounds of brass cased ammo fired in slow strings. For those who know, no explanation is needed. For those who don't, this barrel is top of the line. Asking $420 shipped. Paypal/Cashapp/Venmo.
  2. ShotgunDiesel

    Firearms BCM 12.5” .223 pistol

    Testing the waters. I need to get a longer barrel rifle for an upcoming match. This is a full BCM upper with BCM BCG and charging handle. BCM marked (Troy I believe) back up rear sight. Mlock fore end with the front sight post. Front sight post is not the gas block. Lower is an Aero. BCM...
  3. R

    Accessories XM2010 RACS Chassis (SOLD)

    3500.00 shipped. Remington Defense XM2010 RACS Chassis in black. Ended up with a couple of these with the intention of a clone build but I’m not sure I’m ever going to get around to it. Someone more motivated can run with it and if you need more than one that can be accomplished as well.
  4. Eric_H

    XPS2 sight picture on PTR MP5 Clone

    Anyone ever run this setup? Curious how much of front sight hood is going to be in sight picture. I know it’s a non issue with the raised base of the (E)XPS2 but can’t confirm for the smaller model.
  5. T

    SOLD WTS: McMillan A1-3 Short Action Stock Price Reduced

    Selling a used McMillan A1-3 Short Action Stock in Olive Drab Green Its been milled to take a Badger Ordnance M5 BDM but should be able to adapt to a M4 BDM for use with a XM-3 clone build, Major Price Reduction, I need to sell this before I transfer to my new command. Asking (was $650.00)...
  6. T

    SOLD WTS: MK13 Mod 5 Chassis

    Sold! Want to sell a Accuracy International Long Action Chassis in FDE, comes with 1 five round magazine Asking $1750.00 Shipped I can take Venmo or PayPal
  7. U

    M110 clone help! Please

    Hey all, Currently building a m110 clone for my dads retirement gift and I'm stuck. I was looking at a barrel that Charlies customs offers. Its there reproduced m110 barrel w/ gas block. The issue im running into now is an upper to slap the barrel into. They say only a kac upper will fit. I...
  8. Dvando20

    30mm, M40A1 Unertl style base/rings?

    Are there any places that can custom build a high quality M40A1 Unertl style welded one piece base/rings in 30mm? I am budget building an A1 clone using an SWFA 10x MIL/MOA which uses a 30mm tube. I am currently using a Badger steel 20moa base and steel Max-50 rings because I like durability...
  9. Dvando20

    Rifle Scopes 30mm, M40A1 Unertl style base/rings?

    Are there any places that can custom build a high quality M40A1 Unertl style welded one piece base/rings in 30mm? I am budget building an A1 clone using an SWFA 10x MIL/MOA which uses a 30mm tube. I am currently using a Badger steel 20moa base and steel Max-50 rings because I like durability...
  10. S

    Accessories Sold

    For sale used MPA BA chassis for Remington 700 SA and clones. Chassis is in good condition. Some marks under mag well and in front of cheek piece. Has spigot, NV bridge, and barricade stop. Non-folding standard LOP. I will UPS in to lower 48. $700.00 OBO. As I write this I see the action...
  11. F

    175 grn fgmm clone

    just got 200 new peices of brass and want to make a fgmm 175 clone, but possibly only have 178 amax avialable, oand have rl 15 and varget, need a load suggestion to start. its a 10 twist LW 21" barrel with a match chamber done by hd rifles if that matters. Thanks in advance guys
  12. mtm87tx

    Colt 6920 or MP5 clone

    i just want a new rifle for plinking i have 4 ar15s right now but no just normal 16" 223 what would you buy and why
  13. X

    308 175g BlackHills Clone with Varget?

    Anyone have a good clone recipe for Black Hills Match 175g SMK or FedGMM using Varget? I'm guess in the 40.0g area. xdeano
  14. sobrbiker883

    175 FGMM clone w/IMR4895?

    Anyone have a clone load for 175 FedGMM using IMR4895?
  15. LoneWolfUSMC

    Yay, my FGMM clone worked!

    I am pretty stoked. I just got back from the range and shot my handloads back to back with my duty ammo (168gr Gold Metal Match) with the same zero. Shooting two different zero's is a pain. While my preferred load is hotter and more accurate I will give up a little bit of accuracy for the...
  16. T

    My latest project rifle...CETME/HK91 Clone!

    While definately not a Sniper Rifle, I have always wanted to pickup a CETME or HK91 Clone. I sell parts and accessories, but few of my suppliers carry them for this oldie but goodie. So I instead chose to focus on the AR15 Platform and to a lesser degree the Remington 700 platform for my...
  17. K

    US M24 SWS clone build/rebuild ?s

    OK guys, I'm a newbie that could really use some help here, so here goes. I recently purchased an M24 clone here on the Hide. I'm new to boltguns and precision shooting in general, but I am also a US military collctor so I really liked the idea of getting an M24. The rifle is great, the only...
  18. U

    First Post - M40A3 clone build

    So, I am making my first post. I am building an M40A3 clone. I am starting with a brand new stock 700P, and I have thus far acquired the trigger guard and the Schneider bbl. I will be ordering the stock ASAP and I plan on using this sight for it's wealth of information. My first question...
  19. K

    KAC M110 SASS clone build ?s

    Hey guys, I'm planning to convert an older KAC SR25 into a clone KAC M110 SASS build (as much as I can). Some stuff I appreciate can't be changed, like the fact that the SASS upper has an integral brass deflector and the SR25 doesn't, different lower markings, etc. But I have managed to source...
  20. biben

    Rifle Scopes WTK: Aimpoint clone

    I saw them everywhere. Has anyone use them? How reliable they are?