You are not. I have 2 AT’s and only shoot a single caliber in each of them so the barrels are very rarely removed.
You are not. I have 2 AT’s and only shoot a single caliber in each of them so the barrels are very rarely removed.
Burt babe get ovha heah
Small varmint kills (the bastards!)
We have a coyote kill thread so why not one dedicated to the smaller bastards? Here’s some ground squirrels in Wisconsin that will burrow no more… 17 Hornet 🐝 🐝 22LR CCI SV Not sure which gun.
www.snipershide.com
The AXSA just got a straight tube 6.5. I wish it was 7 or 7.5T but at the time of ordering I got an 8T with plans to only shoot 140s. Going to try the 153s, but I’m not too confident they’ll stabilize properly.
Barrel is THICK. Makes the AXSR HV barrel look tiny
Barrel is THICK. Makes the AXSR HV barrel look tiny
Attachments
That makes my new Brux 10 twist look wimpy in comparison.
153 Bergers shoot pretty well out of my 26" 1:8.The AXSA just got a straight tube 6.5. I wish it was 7 or 7.5T but at the time of ordering I got an 8T with plans to only shoot 140s. Going to try the 153s, but I’m not too confident they’ll stabilize properly.
Barrel is THICK. Makes the AXSR HV barrel look tiny
After having a straight contour for a while, looking at a normal contour looks odd.The AXSA just got a straight tube 6.5. I wish it was 7 or 7.5T but at the time of ordering I got an 8T with plans to only shoot 140s. Going to try the 153s, but I’m not too confident they’ll stabilize properly.
Barrel is THICK. Makes the AXSR HV barrel look tiny
#matchdaylayoutguesswereready
#pcipccs
#ifyaknowyaknow
#abuserofbarrelcerakote
#isitasniperrifleifyouarenotasniper?
#itsnotaleupold
#dmmefortherestofthefeetpicsonOF
#pcipccs
#ifyaknowyaknow
#abuserofbarrelcerakote
#isitasniperrifleifyouarenotasniper?
#itsnotaleupold
#dmmefortherestofthefeetpicsonOF
Wow dude, you gonna take any allen wrenches to this match or you just gonna hope other guys got ya covered? Haha
It will probably be my own is how it usually goes but stoked for to prep for NF hopefully again this yearGo kick some ass brother
Redemption at the ranch Preston id 2 day light elr. the format is like NF and KRG.
I have two black thumbhole ATs with the exact same scope rings and scopes.
One if them is in .308 Winchestore, while the other is in 6.5mm Creedmore.
Last edited:
Trying a 300nm improved this year so far the juice isn't worth the squeeze.
Thunder beast 50 can making an appearance
That's not my rifle... Ai in the center homie
But that's the other guy she is telling you he's just a friend
18% more powder for only about 125fps gain over 300prc
But it's cool. We all have to play with cool stuff from time to time... even if it turns out to be a dud later.
I'm playing with a 7-300PRC. Cool, but it isn't turning out as cool as I wanted it to be in my mind.
I can understand. I’ve been back and forth so many times. I’ve got 60 rounds of ammo (Berger 215 handloads in Peterson brass left over from previous 300NM barrel I sold) as well as the bolt for my AXSR and 300NM dies so I’ve been leaning towards getting that barrel. Plus there’s several in stock I’d be happy with.
That being said I haven’t pulled the trigger on said barrel yet because deep down I fear 300PRC makes more sense. I can get dies, and only 60 rounds/brass isn’t a ton. I can find a .300 bolt for my ASXR. So…..
Damn. This is tough.
Everyone I know (only a few) says that the effort to fireform, cost of dies and any other brass prep tool, does not warrant the minimal velocity increase. About the only good thing with 300NMI is the reduced brass growth. They all say it's the worst cartridge to improve.
My buddy's 28" 300NMI with N568, 245 LRHTs was 2970, vs my standard 27" 300NM 250 Atips, with RL50 at 2930.
My buddy's 28" 300NMI with N568, 245 LRHTs was 2970, vs my standard 27" 300NM 250 Atips, with RL50 at 2930.
Yeah, not much of a improvement. I'm running N570 with the 245s 2950ish out of a normal 300NM on a 26" barrel. Took a lot of different combos to get there, and had to have my freebore extended, but it's happy now. Just counting down the rounds when N570 is going to kill this barrel.
Curious - with AXMC/AXSR, where is the juice vs the squeeze over the 300NM? Or is there?
Similar threads
