My Inexpensive Tac Table Solution

[Burdy]

I built a very inexpensive Tac Table Setup here, that works surprisingly well. For those not looking to spend a fortune:
$45 Sun and Shadow Gen III Tripod table
$25 Etsy POI Kestrel Holder
$10 x 2 Triggercam Pic Rail Accessory Mount (On sale for $10, down from $39.99)

So for $90 and the price of two 5 slot MLOK pic rail pieces it works.
Bag is an Armageddon Gear Pint Size

 

[flogxal]

I made a less fancy one with a small kitchen cutting board from ACE, a drill, an ARCA shoe, and two screws/washers/nuts from ACE. Put a wide strip of grip tape/stair tread tape across the top also.

 

[Smokeshot]

I made a less fancy one with a small kitchen cutting board from ACE, a drill, an ARCA shoe, and two screws/washers/nuts from ACE. Put a wide strip of grip tape/stair tread tape across the top also.

Can you post a picture here, please?

 

[godofthunder]

We sell barebones cheap ones ($55) that are laser cut AL table with cnc machined AL arca mount: https://www.snipershide.com/shooting/threads/catt-cheap-ass-tac-table.7151671/

Drill holes, add mounts, do whatever as you see fit.

 

[Trigger Monkey]

I made a less fancy one with a small kitchen cutting board from ACE, a drill, an ARCA shoe, and two screws/washers/nuts from ACE. Put a wide strip of grip tape/stair tread tape across the top also.

I made one that similar to that too and it's worked well for quite a while.

I'm going to try out a new one made from a bamboo cutting board I saw at the grocery store that will have some mlok inserts embedded in it, a non-skid surface, and a lower profile arca rail on the bottom. Maybe some 1/4-20 inserts for attaching other accessories too.

 

[ballisticdaddy]

We sell barebones cheap ones ($55) that are laser cut AL table with cnc machined AL arca mount: https://www.snipershide.com/shooting/threads/catt-cheap-ass-tac-table.7151671/

Drill holes, add mounts, do whatever as you see fit.

I picked one of these up a few years back and can't beat it for the money

 

[flogxal]

Can you post a picture here, please?

Sure, I'll post some pics later today. EDIT: See below.

For size reference -- that little piece of pressboard is about the same size as the rectangular bottom of an AG Gamechanger Extra Schmedium. And the little hanger-hole was already in the cutting board.

 

[Trigger Monkey]

I'm 90% done with this one, just going to paint it over the weekend. It's not pretty but it's functional.

- 6" X 9" mini bamboo cutting board
- Low profile Arca plate
- Jessup non skid tape
- MLOK inserts
- 10-32 screws and hardware

 

[Maelstrom]

I built a very inexpensive Tac Table Setup here, that works surprisingly well. For those not looking to spend a fortune:
$45 Sun and Shadow Gen III Tripod table
$25 Etsy POI Kestrel Holder
$10 x 2 Triggercam Pic Rail Accessory Mount (On sale for $10, down from $39.99)

So for $90 and the price of two 5 slot MLOK pic rail pieces it works.
Bag is an Armageddon Gear Pint Size

View attachment 8778090

Do you have links for the parts used? I am wanting to do the something very similar.

 

[Burdy]

Do you have links for the parts used? I am wanting to do the something very similar.

Yes sir:

Picatinny Rail Accessory Mount

This Picatinny rail accessory mount allows various shooting accessories to be mounted directly to your rifle. Accessories mount to the clamp using the included 1/4 x 20 screw. Picatinny Accessory Mount clamps to your: Top Side Bottom Picatinny rail Use for: Radar Chronographs Weather Meters...

www.triggercamusa.com

STORE | Sun and Shadow

www.sunnshadow.com

https://www.etsy.com/listing/1425080973/kestrel-mount