Printed Precision Trickler

[zr600]

Used a charge master and would verify on the ad

 

[penguinofsleep]

Are there any videos of a powder change with the PP trickler out there or is someone willing to make a quick video highlighting the process (even if you don't actually do it)?

Ready to buy this thing or the IP trickler but haven't been able to get in touch with PP.
Primarily wondering about powder changes (not limited to the powder, but anything else I may need to change too) and about compatibility with small extruded powder compatibility right now.

 

[Bevo]

PP hasn’t worked for anything smaller than Varget for me. 8208 and N133 don’t work well for me.

 

[biggershooter]

Are there any videos of a powder change with the PP trickler out there or is someone willing to make a quick video highlighting the process (even if you don't actually do it)?

Just empty the existing powder and put the new one in. Do a calibration cycle, which takes a few seconds, or just power it down and up and it will automatically calibrate. No 'fine tuning', no messing with obscure parameters, it self-calibrates and tunes.

about compatibility with small extruded powder compatibility right now.

I had some trouble with H322, which is a very short extruded. It worked, but did relatively too many overthrows.
It is, however, working perfectly with H4350, which is in my video.

 

[NiteQwill]

Are there any videos of a powder change with the PP trickler out there or is someone willing to make a quick video highlighting the process (even if you don't actually do it)?

Ready to buy this thing or the IP trickler but haven't been able to get in touch with PP.
Primarily wondering about powder changes (not limited to the powder, but anything else I may need to change too) and about compatibility with small extruded powder compatibility right now.

The creator has been out of the country for a bit. He will get back to you or chime in here.

 

[secondofangle2]

Received this AM. IM #64 now

 

[ac338in]

Received the same this morning. Looks like you beat me to it I’m #65.

 

[huntshootCO6]

Website is updated as of yesterday as well. Sounds like next round of wait list will be contacted this week. interested to see how many units go out in the next batch.

 

[oldnewguy]

#50 here, I was wondering where that puts me

 

[Jnull]

#44, I haven’t received any emails since my initial reservation but I also haven’t reached out since either.

 

[biggershooter]

Website is updated as of yesterday as well.

Comms through the website have been pretty good and reasonably accurate.

 

[huntshootCO6]

Comms through the website have been pretty good and reasonably accurate.

Very good communication and especially by comparison to others. I'm in the 20s for reservation so hope to be able to report back here sooner than later. Couple more one day matches this summer/fall and then hunting seasons to load for so ill be motivated to get it up and running ASAP.

 

[Jingoist]

#50 here, I was wondering where that puts me

I'm going to go out on a limb here, but you are probably 50th, más o menos.

 

[ifgator]

I'm going to go out on a limb here, but you are probably 50th, más o menos.

I know what you mean. I’m number 45ish and I wonder what is up first for the next batch.

 

[wkarma]

Website update (crazy how that works....)! Prepare for more PP!

As of August 24th the new circuit board order has arrived and I am both doing QC checks as well as populating chips into the boards. Parts have been printed in the meantime, and assembly of the full trickler systems will commence as soon as boards are prepared.

Availability notifications for the next batch of trickler systems will begin to go out no later than August 30th, and I will be reaching out in the order of the reservation numbers provided. If you have a reservation number please do try to check your emails as I will be asking for billing/shipping information to send out invoices for purchase.

I apologize for the unexpected additional delay, but I thank you for your patience throughout the process of tackling unforseen supply chain difficulties and I look forwards to getting more Printed Precision Trickler systems into your hands in the coming month and beyond.

 

[huntshootCO6]

Emails are going out for batch #2 ‐ just confirmed a unit

 

[ac338in]

Was there any indication to how many are expected to go out on this second batch? I’m sitting at 65 just hoping I get this email before I get the other waitlist I’m on.

 

[huntshootCO6]

Was there any indication to how many are expected to go out on this second batch? I’m sitting at 65 just hoping I get this email before I get the other waitlist I’m on.

No word on that in my communications. I did receive and pay an invoice first thing this morning. Maybe someone who knows PP can fill us in on the plans.

 

[FNG1001]

Would be helpful to have videos on the official website of the product. Several of us are on the fence with this product without seeing it.

 

[biggershooter]

Would be helpful to have videos on the official website of the product. Several of us are on the fence with this product without seeing it.

This isn't official, but it may help you:

 

[cavegeo64]

Just received my reservation number, 79.

 

[Jingoist]

Given they are ~1/3 the price, how is the wait-list not in the thousands with everyone getting at least 2-3 of these bad mamma jammas?

 

[ForceMajeure]

A very detailed updated made to the PP website yesterday. The level of transparency is commendable, although the delivery timeline it implies for those of us with higher reservation numbers is a bit disappointing.

 

[secondofangle2]

Maybe one of his "machines is down" and the rep won't come and fix it

Paul at least has time to catch up at the PPT advertised rate of shipping 3-6 machines per week