Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Offer valid until 9/23! If you have an annual subscription on Sniper's Hide, subscribe below and you'll be refunded the difference.
SubscribeUsing the EC tuner on a 22" MTU barrel and SK STD+ at 50 yards. I think it likes setting #12.
Not really, the wind was really picking up. The bottom left target was the confirmation group after tightening the set screws. Then I proceeded to verify my dope for an upcoming match.Definitely! Did you try additional groups with that setting?
I would like to see how it does at 100 and 150. Been thinking about getting one.Not really, the wind was really picking up. The bottom left target was the confirmation group after tightening the set screws. Then I proceeded to verify my dope for an upcoming match.
NiceUsing the EC tuner on a 22" MTU barrel and SK STD+ at 50 yards. I think it likes setting #12.
Mostly buttoned up! Can't get enough height out of the Grayboe cheek piece so WeiBad to the rescue! Other than that I am pleased, tickled, and in awe of the Vudoo! Can't wait to send some rounds down range this weekend! Crappy photo on the kitchen counter...Awesome sauce!! Post pics!
Mostly buttoned up! Can't get enough height out of the Grayboe cheek piece so WeiBad to the rescue! Other than that I am pleased, tickled, and in awe of the Vudoo! Can't wait to send some rounds down range this weekend! Crappy photo on the kitchen counter...
View attachment 7813823
I would move the rear ring back as far as possible.So serious question from an overly paranoid Vudoo owner...
Would y'all move that back ring further back or let it eat? The front one has to say where it is for eye relief reasons but would the gurus of the rimfire realm move it or no? Thank you for the input and let the flaming begin!
So serious question from an overly paranoid Vudoo owner...
Would y'all move that back ring further back or let it eat? The front one has to say where it is for eye relief reasons but would the gurus of the rimfire realm move it or no? Thank you for the input and let the flaming begin!
I'm 6 foot and do have a longish neck. I set up all my rifles for the prone position if that matters? And I'm sure my fundamentals are horrible!Curious, how tall are you? From the way it's setup with the scope as far forward as it is, seems like you're tall / have a very long neck.
nikonNUT's eye piece looks about the same location as mine, I'm 6' 3", his might look farther forward though, because the main tube is shorter.Curious, how tall are you? From the way it's setup with the scope as far forward as it is, seems like you're tall / have a very long neck.
Any one piece mount (Spuhr, ARC, MPA, etc) is going to have the rings exactly where yours are.So serious question from an overly paranoid Vudoo owner...
Would y'all move that back ring further back or let it eat? The front one has to say where it is for eye relief reasons but would the gurus of the rimfire realm move it or no? Thank you for the input and let the flaming begin!
I'm running a Cronus on a 40moa rail and have 7.6 mils under my zero stop, I should have enough to go to a 60moa rail, but haven't tried...yet.Is anyone successfully using a 60 MOA base with a Poortex Strike Eagle? I have a little over 11 mils left below zero on a 1.5" height mount and 40 MOA base using a 50-yard zero with SK STD+.
SpreadSo serious question from an overly paranoid Vudoo owner...
Would y'all move that back ring further back or let it eat? The front one has to say where it is for eye relief reasons but would the gurus of the rimfire realm move it or no? Thank you for the input and let the flaming begin!
Spread rings. I think scope is far enough back.So serious question from an overly paranoid Vudoo owner...
Would y'all move that back ring further back or let it eat? The front one has to say where it is for eye relief reasons but would the gurus of the rimfire realm move it or no? Thank you for the input and let the flaming begin!
Thank you kindly @littlepod! That is good info to have , sir. I wish I could run higher rings but, sadly, all of the stocked rifles I have lack in check riser height. A chassis or a Manners TCC-PRS stock might be in the future and that might facilitate higher rings. I will give the colarbone thing a try! Thank you for the tips.I followed a lot of the snipers hide training -
1. Positioning of the rifle is now more centerline with the body on the collar bone instead of the shoulder crease.
2. Height of rings as high as possible that your cheek riser will allow to prevent less tilting of the head.
Your rifle is looking great, go out and have some fun!
My buddy has a 60 moa rail and a strike eagle. He has about a half mil left over with SK rifle match. Cutting it a little close but it works.Is anyone successfully using a 60 MOA base with a Poortex Strike Eagle? I have a little over 11 mils left below zero on a 1.5" height mount and 40 MOA base using a 50-yard zero with SK STD+.
TCS wont work. Needs a different mag latchThank you kindly @littlepod! That is good info to have , sir. I wish I could run higher rings but, sadly, none of the stocked rifles I have lack in check riser height. A chassis or a Manners TCC-PRS stock might be in the future and that might facilitate higher rings. I will give the colarbone thing a try! Thank you for the tips.
What ammo are you running?Well DANG! The Vudoo makes my sorry ass look good! Got her zeroed and 1st group was in the .2s at 50 yards. I should have done this sooner!!!
That's a long way form the T1x.The new Vudoo and XLR Envy Pro go together like peanut butter and jelly
Nice rifle. Did you go with the 60 or 90 degree? I really want the new XLR C-6 buttstock. How do you like it?The new Vudoo and XLR Envy Pro go together like peanut butter and jelly
That's a long way form the T1x.
Edit: How much does it weigh and how do you like the SendIt level? I just picked one up in the PX and have only used it at the range breaking in brass and working up a load for my 6GT, so I'm just getting used to it. I like that I don't have to look at it to know if I'm level/out of level AND which direction. What sensitivity?
Nice rifle. Did you go with the 60 or 90 degree? I really want the new XLR C-6 buttstock. How do you like it?
I put a Send-iT on mine too, it's a cool gadget. I left it on the default settings too. Need to get some spare batteries to throw in my range bag.The send-it level just reduces the time and lets me get level really quickly. Pretty brain dead to use. Red means turn the right, and bLue means left. I didn't adjust any sensitivity settings so I'm not sure. I also can see the green light when I'm on support side the way mine is mounted so I can use it. Only downside is forgetting to turn it off and letting it bounce in the back of the car for an hour drive and then the battery is dead.
@littlepod What's the minimum LOP on the C6 buttstock?
One reason I like the XLRs so much is the precise LOP adjustment, and the ability to go down to 12.5" ish +/-.
Looks like yours is at minimum? What the LOP from trigger curve to rear of butt pad if you don't mind?
And of course, the obligatory XLR/V22/ZCO pic
Excellent, thank you, I may have to try the short LOP C6.
I swap the Pachmeyers off my MPAs to run on my XLRs, that thick squishy pad they ship with is a no-go...
Best double check that with the bottom metal in hand. When I tried two badger BDM's at MHSA, the vudoo mags I had literally fell right through them with no engagement of the mag release at. Went with Hawkins Precision M5 DBM instead as they retained the mags properly.Can someone confirm if I buy a voodoo will the mags work if I use a badger ordnance M5 bottom metal. Just making sure forgive me if it has been asked before
@Tiger_ShiloneBest double check that with the bottom metal in hand. When I tried two badger BDM's at MHSA, the vudoo mags I had literally fell right through them with no engagement of the mag release at. Went with Hawkins Precision M5 DBM instead as they retained the mags properly.
Keep in mind that Vudoo is on at least 3 generations of magazines at this point in early 2022. My last four mags (3rd gen+) are longer then the previous 7 (2nd gen) by about .012-.015" the Previous 1st gen mags I had prior to those were also longer. I need to measure the new ones and see what the dimensional differences are. This is kind of irritating as I had modified a Hawkins magwell to eliminate any rocking on a barricade stop and now the new 3rd mags will not fit in it
Littlepod of the two in your opinion which is the one with the least problems. My plan is to buy a barreled action just have not made up my mind on which of the 2 I should get
Cool, it better than getting a new truck, when did you order your Gen 3 ?Soooooo, I got the call yesterday! My 360 is in route, by the tracking number it arrives next Wednesday!!! I am stoked!