• Frank's Lesson's Contest

    We want to see your skills! Post a video between now and November 1st showing what you've learned from Frank's lessons and 3 people will be selected to win a free shirt. Good luck everyone!

    Create a channel Learn more
  • Having trouble using the site?

    Contact support

Gunsmithing er shaw barrels ?

cjmac1988

Private
Full Member
Minuteman
Sep 19, 2013
78
1
anyone use er shaw barrels? are thay worth a crap. im on kinda a tight budget but have a tikka t3 in 308 id love to use the action for a build. because its so smooth and a great trigger. i know a mcmillan stock is about 600 bucks, but what is a good barrel at fair price in 243 ? wonder if anyone would make one threaded and chambered
 
The old phrase "Buy once cry once" comes to mind here, go with quality (I.E. Brux, Shilen, Krieger, Rock Creek, Etc.) You will be happier in the long run. The Tikka action is a good platform to start with and should save you a little money as IMO they do not need to be trued, but if you're spending $600 on a McMillan stock save a few extra bucks up and get a good barrel to go along with it.
 
Where are you located? your best bet is to have a gunsmith fit and chamber a barrel blank to your action, Some barrel makers will thread and short chamber the barrel but then you still have to finish cutting the chamber for proper headspace. I would not suggest taking this on unless you have a solid working knowledge base pertaining to how and why things work inside your rifle when you pull the trigger..

I ask where you are located so we can direct you toward a qualified person to fit/chamber your barrel for you.
 
I have a shaw that is chambered in 7mm08 and it is one of the most accurate barrels I have owned. I would call it a hummer. I have seen several with very rough chambers in the shoulder area. I would say it depends on what you want to do with it. Rebarrel an old hunting gun? Go for it. A gun where accuracy is the most critical component, Not so much.
 
anyone use er shaw barrels? are thay worth a crap. im on kinda a tight budget but have a tikka t3 in 308 id love to use the action for a build. because its so smooth and a great trigger. i know a mcmillan stock is about 600 bucks, but what is a good barrel at fair price in 243 ? wonder if anyone would make one threaded and chambered


less cost does not = less performance. I've seen excellent reviews on their barrels. But I must admit when faced with the same choice for the same reasons, I went with the premium barrel. In my case a Krieger.
 
I also have one on 7-08.
Depends on how "accurate" you're looking to be...
Mine's about a 3/4 minute barrel. For the $$, I'd say it's a good value- and mine still shoots better than I can- for now.
You want half-minute or better? Pay more as mentioned above.

When I get to the point where that extra 1/4 minute or so is making that difference at 1000 yards- rather than my wind calls- I'll move "up".
 
I have an ERShaw, .223, 1/12" twisted 24" barrel and cant get it to shoot any of my loads over .530" @ 100 yds. Darn thing just keeps the bullets in a nice small group.
I went & bought another for a backup barrel.
 
I have an ER Shaw on my Model 70 .308, and most of my groups are under 1moa, from prone, no bag just bipod. Through load development, ive been able to get one hole clover leafs , and get consistent minute of man hits on steel out to 650yds. Its the only custom barrel I have experience with, but I would say its at least not a bad money/quality compromise.
 
I twisted a Adams & Bennett tube on a mauser action and it was a tack driver. Would I buy another for a custom build? Hell no. Our preference is Rock Creek, but there are many other quality tubes available. You can send your action to Rock and they'll thread it and install/headspace it to your action.

Don't gamble on a cheap tube.
 
im in pensacola ,fl doing machine work is no big deal for me . im a welder - machinist by trade BUT not for guns lol

Its not hard brother. Turning barrels is a lot easier than any part Ive machined outside the gun industry. You can do it, and the satisfaction you will get is worth more than the money you will save. Ive had great Shaw barrels and some mediocre ones. But you cant send it back once you spin it, so I go with any of the higher end ones.
 
I twisted a Adams & Bennett tube on a mauser action and it was a tack driver. Would I buy another for a custom build? Hell no. Our preference is Rock Creek, but there are many other quality tubes available. You can send your action to Rock and they'll thread it and install/headspace it to your action.

Don't gamble on a cheap tube.

I can't stop staring at your avatar! Guess I am a pervert! lol
 
IMO ER Shaw barrels are a "Medium Tier" barrel. Usually better than the run of the mill mass produced barrel but not up to the quality and consistency of a Top Tier custom barrel maker. I would rate ER Shaw with Wilson Barrels and Green Mountain Barrels.

What you're paying for in a Top Tier maker is putting the odds in your favor of getting a barrel that will be a shooter. I'm sure there are ER Shaw barrels that will hold 0.5 MOA, but they are probably the exception, rather than the rule. And if it doesn't, what recourse do you have with ER Shaw........ none because I'm sure it's still within their acceptable accuracy range. Once you tally up all the costs and time of fitting a barrel blank and load development, the money saved isn't worth the gamble. People want a sure thing.

That said, I have to admit that I did chamber and spin on a Adams & Bennett $39 barrel to a M700 action. I knew it was a total gamble and the odds were against me. I didn't expect much but was shocked to find it was a shooter. Consistent 3/4 moa from a light sporter contour. Haven't pressed my luck since...
 
Last edited: