Search results

I had excellent service with Daniel Defense. I had an old DD5v1 rifle that I bought used years ago and was in pretty rough shape from pig/coyote hunting. Purchased a new 6.5 creedmoor upper to use with my old lower and had some problems with it functioning. Called them and told them about it...

Looking for a new trigger for my coyote/pig gun. Currently running a Geissele two stage trigger and would like to switch to a single stage for this rifle. What do you guys think the best bang for buck single stage trigger out there? Hoping to pick up a new one on a July 4th sale somewhere.

H4350

Actually alreay have one. Just want to find a way to run it off this unit.

Not a fan of the trimmer this unit comes with as it never seems like it's precise enough. Starting fiddling with it and was hoping to mount a drill chuck to it so I can run a Giraud or Gunworks trimmer on it. Seems like it would be the perfect setup where I could trim, inside and outside...

I've always made it a habit to do this even on new brass. Is it necessary or am I wasting my time?

What powder are you using?

I've got a DD54v chambered in an 18" 6.5 Cm that I've doing some load development with 90 grain TNT over H4350. After my second outing with it yesterday, I'm scrapping that bullet/powder combination. Just seems to be finicky and inconsistent. I've ordered some 90 Varmageddon bullets and going...

$350 or $3500? Can't be $350, lol

So I've posted this.

So shined a light inside and doesn't seem to be a crack. I actually peeled a couple of cases open with a screwdriver and it doesn't seem to tear on the line. Doubt I'm over lubing as just using one shot. And this develops after I full length size. So you guys think the brass is ok? Will it...

I started working on load development on a Daniel Defense 6.5 creedmoor I'll be using for pig and varmint hunting. Decided to use Hornady Brass due to availability and cost. Purchased some brass new and some once fired brass. I know Hornady isn't the best brass but figured it was fine as it's...

So I'm in the market for a new handheld scanner. Been using a Pulsar Axion Key unit for the last couple of years and want to get something a little better with range finding. I want to stay under $300o and these two seem like the best bet. Have had good luck with the Pulsar units but this...

That little screw is the role pin. It's definitely not locking back with a single round. Haven't dug into it much because we ran out of time. I'm not sure what buffer is being used but does have a fixed rifle stock with the rifle tube. There was no info from the previous owner and it was...

My buddy came over today with a rifle he picked up used and was told it was a gen 1. We had a bunch of different 308 ammo we shot through it and it would usually eject the brass, but not load the next round from the magazine. Has a surefire socom brake so I figured someone adjusted the gas...

So I've been using the Hornady for some years now and think it may be time to replace it with something better/faster. Mine is the older non touch screen unit. It's served me well but wondering if any of the newer ones out there are faster and less prone to overcharging. I've did all the...

So today was a sunny day in Ohio and decided to put my Trijicon scope on my new AR that I've been working with. Haven't moved this off the old gun so it's been a few years since I sited it in. I've always used hand warmers but they gave me hell today with the sun. Is there anything out there...

I'm running hand loads which are 42 grains of H4350 under a 120 grain sierra bullet. This is a moderate load and on the higher end of the reloading data. I haven't played around with the large frames AR's before, but both my prior builds ran fine which were 6mm creedmoor builds. Both those...

https://www.aeroprecisionusa.com/m5-308-enhanced-carbine-buffer-kit This is the kit I purchased for this gun. Figured I'd use it as it's all aero components and figured it would work well with it. You guys think this could be causing my problem? I figured it was the way to go as I wanted an...

So I recently just finished up a 6.5 creedmoor build using all aero components except a 16 inch faxon barrel and superlative adjustable gas block. When I put the aero enhanced 308 carbine buffer tube kit, I noticed the spring was very tight. I dimpled the barrel with a jig to make sure I had...