Wooden siding is rotting and I believe there’s mold between the walls somewhere. I can’t see it but it smells horrible. Talked to the landlord and he basically told me that there’s no money to replace the siding since they just fixed up another rental property. The earliest he can do anything is next Spring.

None of us are allergic or anything but we would like to get rid of the smell. Any suggestions on how to do that?

Selling my Leupold Mk5 PR2 mil. It was listed with mount and accessories in a previous listing but sold the mount and accessories. Comes with sunshade and scope caps. $1500 shipped. PayPal FF.

Thanks!

Like it or not, this is our new reality. For now pravda is helping hide it but you can't hide this for long.



.
Login to view embedded media

Has anybody tried to run 6ARC through their 5.56 can? I’ve noticed the end cap and baffle diameter is large enough for the bullet to freely pass through, and the 6ARC fires with less pressure then the 5.56. So in theory, I feel like it is safe to run it in just to scared to be the first one to try, but I have a a feeling someone in here has done it at some point

Catch and release. Triple pull CKYE pod . Used at one match and half a hog hunt. Love it.

Venmo/PP

Will consider .308/6.5 match grade ammo

$800

I was just trying to remove and retorque the screws on my optics rail to ensure they were correct and 3 of the 4 went without a hitch (factory spec called for 15-20 inch pounds, which I verified with them over the phone before I started, I split the difference at 18), but number 4 (technically number 2, counting from the rear) would not budge and stripped the screw head (number 25 Torx), I have no idea what torque they installed that one at but I’m betting it was WAY more than 20 inch pounds). My question is how much does that matter? Am I good to go just ignoring it or will that throw something off? Do I need to send it in to the factory to get fixed or can I just leave it be since it’s obviously not going anywhere and the other 3 are good?

Rifle is a Ruger Precision Rifle in 6.5 Creedmoor. The stripped screw is the second from the back on the factory picatinny rail. The other 3 are now torqued to 18 inch pounds and Vibra Tight VC-3ed with a 10 minute cure prior to reinstalling.

New McMillan carbon fiber game warden rifle stock. Inletted for Kelby Atlas long action or similar footprint, M5 bottom metal inlet, and fits barrels up to #7 barrel contour.
Weighs 25.2 ounces as pictured.

Asking $900 obo shipped

Leupold Mark 5 7-35 PR2 reticle w/ DI precision wind dial
Area 419 Match rings 35mm Medium
$1,850
I do still have the box as well.

Selling my great condition Leupold Mk5 5-25. Has PR2 mil reticle. Has the Leupold Competiton dial and the DI Precision windage knob. Included as well is a Spuhr Mount (0mil 35mm) and Low Raptor rail. The extras add up to $650+.

No scratches, great condition. $2,000 shipped for everything. No trades at this time. PayPal FF.

Selling my origin .223 trainer as I just picked up another impact. The action has about 550 rds through it. 100x 6gt, and approx 450x 223. I did dremel off the front end of the pic rail to be flush with the reciever like most custom actions. BA is in excellent condition.

- Bighorn Origin w/ both 223 and 308 bolt faces
- Proof comp contour 223 rem, 26” 1/7 T, 5/8x24
- TT special trigger

Package deal $1375 shipped
Barrel and 223 BF $525 shipped
Origin with 308 BF and TT $915 shipped

Shipping is a to the lower 48 only. PayPal or Venmo.

Manners Pro Hunters
Short Action Rem 700 & Clones
Proof Sendero Barrel Contour
*NEW* M5 Micro Chassis
2 flush Cups Left Side

$1100 FIRM SHIPPED

1 - SOLD
2 - SWAMP - 13.5" - LOP - 1/2" PAD
3 - SOLD
4 - SOLD
5 - SOLD

On Thursday’s broadcast of CNBC’s “Squawk Box,” Transportation Secretary Pete Buttigieg stated that building eight electric vehicle charging stations so far under the Inflation Reduction Act’s $7.5 billion investment in electric vehicle charging stations is “on track.” Because most construction will occur in the second half of the decade.

Co-host Joe Kernen asked, “[O]ur designs on electrification of the auto industry, have we recalibrated there? And I’ll just give you one item and you can — maybe you can explain why, but under the Inflation Reduction Act, 7.5 billion for building these charging stations. The latest information, eight have been built with the 7.5 billion that had been allocated. You’re supposed to get to 500,000 of these charging stations by 2030. What is really the problem with — do you — have you looked at that and figured out why?”

Buttigieg responded, “Oh yeah, that’s on track. So, we’re at about 190,000 publicly available charging stations in the U.S. That’s approximately double what the level was when President Biden came in. The issue, though, is that there are some gaps in the market, ones that are just not going to be built by the private sector that’s been building the construction of those chargers to date. That’s why the legislation provided for funding to do federally-supported chargers that are intended to be online before 2030. Now, the bulk of that construction will happen in ’27, ’28, quite a bit, actually, I expect by 2026. A handful, as you mentioned, are actually already up and running. But really what you’re going to see is more in the second half of this decade. And it’s really important to have those federally-supported chargers, because you have stretches of road or even just in the middle of our cities, apartment buildings, places in our economy where it just doesn’t yet pencil out for there to be the private sector profitably doing that. And even though about 80% of EV charging happens at home, the reality is that the new EV kind of landscape we’re working toward where the president’s goal is about half of sales to be EVs by the end of this decade requires us, by the end of this decade, to have a lot of charging apparatus that just isn’t there as we’re sitting here in 2024.”

Bought this off another member on here about 3 months ago. I’ve only put 2 rounds down the tube since I’ve had it. Previous owner stated 300rds. Scope I mounted was already on a previous 6.5 so the adjustment was minimal to get back to zero. Count is now approx 302 rds.

- Lone Peak Fuzion SA
- 24.5” Bartlein heavy palma 1/8 twist
- Chambered, cerakoted graphite black, cut & threaded 5/8x24 by LRI

There is a couple vise marks on the barrel as pictured. Otherwise excellent condition.

$1825 shipped to the lower 48. Your ffl must accept from an individual. PayPal or Venmo.

** 9/25 now open to trades. Mostly interested in a MK5 5-25x PR2 Mil, but will look at other offers**

I was looking into a different powder for my 308 load with 155 scenars. Currently using 47.5g Varget, CCI-200, R-P Brass, CBTO 2.216" or 2.835" COAL. This gives me .050" jump on a fairly new Tikka CTR 308 20" barrel. That load is compressed pretty good and yields 2840 avg and a 10 shot moa or less groiup at 100.

When I looked on Gordons, it looks like I'm not getting 100% burn in that short of tube. So I decided to give 8208xbr a shot. Have a lb of it and its starting to show back up. Loaded 44, 44.5, 45 & 45.3 (book max) and went shoot for pressure. Saw nothing. Primer looked fine, very easy bolt lift, no swipes or ejector marks. So loaded up a few just to see. Neither were near compressed loads, so I liked that.

45g 8208, 2.216" CBTO, .050" jump
45.3g 8208, 2.216" CBTO, .050" jump

What I noticed was the SD/ES were ridiculously low and velocities were up. It was +90* when I was shooting and humidity was like breathing pea soup. When I tested for pressure, I didn't see anything to speak of, but when I shot these 3 rounds each to get some velo numbers, I noticed a few things on the case head.



Of course, only 3 shots, but 45 was .617" and 45.3 was .412" at only 100 yard (I was limited by this range)

I did notice a slight ejector mark on 1 of each set. So should I back down to 44 / 44.5 and work back up to 45? I have .050" to play with. Do I seat longer to relieve case pressure but closer to lands will build pressure back up? Any thought yall have would be greatly appreciated.

I just installed a Criterion barrel cambered in 30-06 on my remmington 700. Checked head space with go and no go gauges MULTIPLE times even put a piece of scotch tape on back of the go gauge and bolt wouldn’t close. Take it off and it closes. Ejector was removed during all of this.

This is my concern I pulled out a box of factory federal fusion ammo 165 grain to check feeding and the first round fed in the chamber but the bolt was EXTREMELY hard to close. All other 19 rounds in the box fed fine and the bolt closed fine. No visual difference in the round that didn’t feed and even tried some Hornady match ammo and it fed fine and bolt closed fine.

Just scratch it up to a bad factory round?

Impulse bought this from a member here very recently.
Set it up and loaded 50 rounds and realized this is so much more equipment than I need.

I mainly load for 16” ar’s and hunting rifles. Going to stick with my cheap o rcbs.

Functions amazing, like new condition.

$1020 shipped

MDT Ckyepod in PRS length. I’m just getting out of the sport for a little bit. $400

For some reason, my money is on the Sheriff...

Wonder what the 'judge' was up to.

Then again, I could be wrong.

Sirhr

Hi everyone, i have always used the flaslight method, confirming later using house walls at a distance to make sure the reticles of the scopes of my hunting rifles were mounted straight to gravity.

Now i moved to a new house and i can place a plumb line 20 yards away when mounting the scope. I read on forums that a 100 yards plumb line is better. Why is that? As long as i can focus the rope at 20 yards (my NF has parallax adjustments), shouldn't the process be as accurate as hanging the rope at 100 yards?

Am i missing something?

Thanks!

Gets 80 to 120 years.
Login to view embedded media

Hey fellas. Below is a list of optics I've decided to part with. All used but in excellent condition. I am the original owner of all of them. I sold more than 50 of my 150 firearm collection while living an AZ. Most of these are the optics that were mounted on those firearms. Just a high end collector selling optics that I don't need anymore.

I don't have much feedback because I'm new here, but I did sell a couple of optics this week to a long time member and the transaction went seamless. @Duckhunter666

1. US OPTICS SN-8 1-8x27mm Digital Red with 2/10 MIL Zeroing Windage & Elevation Knobs with FFP C2 Reticle
$1100

2. US OPTICS SN-8 1-8x27mm Digital Red with 2/10 MIL Zeroing Windage & Elevation Knobs with FFP C2 Reticle
$1100

3. US OPTICS SN-8 1-8x27mm Digital Red with 2/10 MIL Zeroing Windage & Elevation Knobs with FFP C2 Reticle
$1100

4. US OPTICS SN-8 1-8x27mm Digital Red with 2/10 MIL Zeroing Windage & Elevation Knobs with FFP C2 Reticle
$1100

6. US OPTICS FDN 17X 3.2-17x50mm HD EREK Knob FFP MDMOA 34MM Illuminated Reticle
Parallax Adjustment
$1800

8. US OPTICS ST-10 10x37mm EREK Knob MOA Illuminated Reticle Parallax Adjustment
$1200

9. Swarovski Z6 3-18x50mm P HD SFP BT-Plex Reticle Ballistic Turret w/ Aluminum Swarovski Lens Covers
$1500

10. Swarovski Z6 3-18x50mm P HD SFP BT-Plex Reticle Ballistic Turret w/ Aluminum Swarovski Lens Covers
$1500

13. Nightforce NXS 5.5-22x56mm SFP NP-R2 Reticle
$1200

14. Nightforce NXS 5.5-22x56mm SFP MOA Reticle w/ Tenebraex KillFlash
$1200

17. Leupold VX-6 7-42x56mm SFP Side Focus CDS TMOA Plus Reticle
$1300

18.Leupold VX R 3-9x50mm SFP Illuminated Plex Reticle w/ Tenabraex KillFlash
$375

19. Leupold Mark 4 CQ/T 1-3x14mm Circle Dot Reticle 3MOA @ 3x, 9MOA @ 1x
$750

20. Leupold VX-3 1.5-5x20mm FFP CMR Illuminated 300 Blackout Reticle Suppressed/Unsuppressed w/ Leupold Flip Lens Covers
$450

21. Leupold Mark 4 Tactical HAMR 4x24mm Illuminated CMR2 Reticle w/ 7.5 MOA Delta Point Red Dot Sight
$900

22. Leupold Mark 4 1.5-5x20mm MR/T Special Purpose Illuminated Reticl
$900

23. ELCAN SpecterDR 1x/4x Illuminated CX5396 Reticle 100-600m .308/7.62 Carbine, 700-1000m 7.62 LMG w/ Trijicon RMO1 Red Dot Sight
$2000

24. Trijicon ACOG 6x48 .308/7.62M80 BDC 1200m Tritium/Fiber Optic Illuminated Reticle, Trijicon Bindon Aiming Concept, Waterproof 328m
$1800

25. Trijicon Accupoint 2.5-10x56mm MIL-Dot Reticle w/ Green Dot, Tritium/Fiber Optic Illuminated
$600

26. Trijicon Accupoint 1-4x24mm Green Triangle Post Reticle, Tritium/Fiber Optics Illuminated
$500

27. Zeiss Victory FL Diavari 6-24x56mm T FL, Illuminated Rapid-Z 1000 Reticle SFP
$1500

28. Zeiss Victory FL Diavari 4-16x50mm T FL, Rapid-Z 600 Reticle SFP
$1600

30. Meopta Meostar R2 2.5-15x56mm RD, Illuminated FFP 4K Reticle w/ Rubber Lens Covers
$1300

31. Meopta Meostar R1 3-12x56mm, FFP 4B Reticle w/ Rubber Lens Covers
$600

32. Meopta Meostar R1 3-12x56mm, FFP 4B Reticle w/ Rubber Lens Covers
$600

34. Bushnell Elite Tactical ERS 3.5-21x50mm, FFP G2 Reticle, Flat Dark Earth
$1500

36. Bushnell Elite Tactical ERS 3.5-21x50mm, FFP G2 Reticle
$1500

38. Burris Xtreme Tactical XTR II 1.5-8x28mm, FFP Illuminated Ballistic 5.56 Gen3 Reticle w/ Plastic Burris Flip Lens Covers
$700

39. Burris MTAC 1-4x24mm, SFP Illuminated Ballistic AR Reticle
$250

40. Steiner Military Tactical 1-4x24mm, SFP Rapid Dot 308 Illuminated Reticle
$900

41. Schmidt Bender 1.1-4x24 Zenith, FD7 SFP Reticle
$800

42. Leupold Mark 4 LR/T 4.5-14x50mm, Mil-Dot Reticle, w/ Barrett BORS System and Barrett Zero-Gap 30mm High Rigid Scope Rings
$1500

43. Aimpoint Hunter Red Dot H30L 2MOA in box
$600

44. Aimpoint Hunter Red Dot H34L 2MOA
$500

45. Aimpoint Hunter Red Dot H30L 2MOA
$500

46. Aimpoint Hunter Red Dot H30S 2MOA
$500

47. Nikon M-308 4-16x42mm, BDC Reticle
$250

49. Leupold VX-2 IER 1.5-4x28mm Scout, Duplex Reticle
$150

50. Premier Reticles Heritage 3-15x50mm Tactical w/ Illuminated Gen 2 Reticle
$1500

51. Vortex Viper HST 4-16x44mm, Dead Hold BDC MOA Reticle
$300

52. Carl Ziess 18-45x65mm Field Spotter
$1000

53. Leupold SX-2 Kenai 25-60x80mm HD Spotting Scope w/ 30x Eyepiece (Straight View)
$400

54. Bushnell Elite Tactical LMSS 8-40x60mm Zoom Spotting Scope
$700

55. KONUS USA Konuspot 20-60x80mm Angled Spotting Scope
$100

56. SWFA SS 1-6x24mm HD, FFP Illuminated Donut Circle Mil-Scale
$500

57. HI-LUX Optics CMR 1-4x24mm, Illuminated 223/308 BDC Reticle, New in box
$200

58. Nikon M-223 2.5-10x40mm Laser IRT Precision AR Optic, BDC 600 Reticle, New in box
$500

59. Barska Gladiator Zoom Binoculars w/ Tripod Adapter
$80

60. ATN Aries MK 390 Paladin Night Vision Compact Rifle Scope 4x90mm Illuminated Red Duplex Reticle w/ Integral Weaver Mount
$300

61. Leupold Dual Enhanced View D-EVO6x20mm CMR-W Reticle w/ Leupold Carbon Optic LCO REWd Dot Sight Package
$1500

65. Command Arms MSE AQC-1C Reflex Sight w/ Selectable Reticles and Picatinny Rail Mount
$300

66. Aimpoint 3x Magnifier w/ Larue Locking Lever Flip Mount
$600

Looking forward to providing more seamless transactions!

Alright,
let's see how fun this will be.