• Get 25% Off Access To Frank's Online Training

    Use code FRIDAY25 and SATURDAY25 to get 25% off access to Frank’s online training. Want a better deal? Subscribe to get 50% off.

    Get Access Subscribe

Accuracy International Picture Thread

#23,801
My AXSR 37 XC barrel is finally up and running after a 2 year wait.. almost 1 year waiting on the Bartlein modBB blank, shipped 2 blanks halfway across the country only to have them sit at a smiths for a year, ended up having them shipped back to me.. $150 wasted in shipping cost 😡…..

Than hand delivered my blank to Greg at SPR aka Bugholes along with my JGS custom 37XC CEB reamer. SPR crew knocked this barrel out of the park. 4 week turn around time.. Huge shout out to Greg/Russ @ Bugholes..
IMG_9076.jpeg
IMG_9063.jpeg
IMG_9062.jpeg
 
  • Like
Reactions: Huskydriver, Part Timer, Terry Cross and 9 others
#23,802
Nik H said:
First time firing a new barrel. I didn't see any grooves in the bullet when I cycled them before firing.

But great suggestions, TY.
Click to expand...

All my AI 30 cal barrels HATE Hornady bullets. I was popping primers at 2550 fps with 308 178 BTHP rounds. I even pulled down FGMM 175 rounds which shot at 2700 just fine and put the 178 in making sure to not touch the lands. It was still overpressure by a massive amount.

I have no idea why, but it is consistent across guns, barrels from both Bartlein and LW, and across OAL variances, charges, and case type.

The ONLY thing it could be is the bullet. I have seen this in 30-06 with Hornady 208s as well.
 
  • Like
Reactions: Terry Cross and Nik H
#23,803
MK20 said:
All my AI 30 cal barrels HATE Hornady bullets. I was popping primers at 2550 fps with 308 178 BTHP rounds. I even pulled down FGMM 175 rounds which shot at 2700 just fine and put the 178 in making sure to not touch the lands. It was still overpressure by a massive amount.

I have no idea why, but it is consistent across guns, barrels from both Bartlein and LW, and across OAL variances, charges, and case type.

The ONLY thing it could be is the bullet. I have seen this in 30-06 with Hornady 208s as well.
Click to expand...
Your experience with the 308 cartridge is something that I also experienced but forgot about. I used those 178 BTHP rounds when I got my 308 barrel for the AXMC. It was a couple of years ago, but I remember the same thing happened. I never used that cartridge again.

I am going to check 20 other randomly selected rounds from this case to see if it was isolated to this box. The Bergers should show up in a week or so.
 
#23,805
Aerem said:
How are you enjoying that maztech (2k or 15k?)? I am on the fence between getting a Tango or Maztech 2k. I am not sure I am ready to drop another 5k+ on the 15k just yet.
Click to expand...

Was my first weekend out with it (15k) and it exceeded my expectations. Zeroing super fast. Ranging was instant out to 750.

The only glaring miss, which I knew going in, is the cord and remote. The cord needs a 90 degree connector out of the unit for those of us with larger turrets.

Buddy of mine got the 2k and FWIW he's a bit disappointed with the speed of the unit.
 
  • Like
Reactions: Aerem
#23,806
chrome said:
Was my first weekend out with it (15k) and it exceeded my expectations. Zeroing super fast. Ranging was instant out to 750.

The only glaring miss, which I knew going in, is the cord and remote. The cord needs a 90 degree connector out of the unit for those of us with larger turrets.

Buddy of mine got the 2k and FWIW he's a bit disappointed with the speed of the unit.
Click to expand...
Thanks for the feedback. From what I've seen the 15k looks like an absolute beast. I can't justify the 15k at the moment given that I am an east coast shooter with 600 yards to play with unless I travel for a match. Even at a match that's going to be ~1200-1400 yards max. I'll probably go Tango, seems to be better than the Maztech 2k, for ~1800 yards and in, at least from a speed perspective.
 
#23,807
Aerem said:
Thanks for the feedback. From what I've seen the 15k looks like an absolute beast. I can't justify the 15k at the moment given that I am an east coast shooter with 600 yards to play with unless I travel for a match. Even at a match that's going to be ~1200-1400 yards max. I'll probably go Tango, seems to be better than the Maztech 2k, for ~1800 yards and in, at least from a speed perspective.
Click to expand...

Can't argue with that logic either, highly probable you'll be very happy with the tango.
 
#23,812
BCX said:
My AXSR 37 XC barrel is finally up and running after a 2 year wait.. almost 1 year waiting on the Bartlein modBB blank, shipped 2 blanks halfway across the country only to have them sit at a smiths for a year, ended up having them shipped back to me.. $150 wasted in shipping cost 😡…..

Than hand delivered my blank to Greg at SPR aka Bugholes along with my JGS custom 37XC CEB reamer. SPR crew knocked this barrel out of the park. 4 week turn around time.. Huge shout out to Greg/Russ @ Bugholes.. View attachment 8745351View attachment 8745352View attachment 8745353
Click to expand...
32’’ barrel ? 1-8 twist? 1.350’’ shank HV contour, I presume.
 
Last edited:
#23,813
Finished 33” plus 4.5 inch brake, it’s a 1.350 shank 1-7.5 modBB modified HV w a muzzle diameter of 1.1, it’s about max diameter you can use on a AXSR… I just ordered 2 more Bart 375 blanks yesterday but I’m changing up the contour a bit for a little more clearance at the forend while still allowing for a spiral flute.
 
  • Like
Reactions: Silvan and Nik H
#23,819
CStroud said:
Looks like MC LE are now available for civilian purchase!

ETA: Hopefully this means the other LE models will be as well, but I have a feeling this is just to get rid of "old" stock.
Click to expand...
The only thing I would be concerned about is replacements, like bolts and firing pins. A lot of that stuff for the MC is like a YEAR out or more if you want one. Unlikely you'd need parts, but its something to consider.

If i didn't blow a ton of money on other stuff lately id probably get one just because the LE version is "Cool". Dark Earth looks like it sold out fast, and that would've been my pick. Good thing it sold out fast lol..
 
  • Like
Reactions: CStroud
#23,821
BCX said:
Finished 33” plus 4.5 inch brake, it’s a 1.350 shank 1-7.5 modBB modified HV w a muzzle diameter of 1.1, it’s about max diameter you can use on a AXSR… I just ordered 2 more Bart 375 blanks yesterday but I’m changing up the contour a bit for a little more clearance at the forend while still allowing for a spiral flute.
Click to expand...

So mine is a 36" , 1.350 for 6" then tapered to 1.1 at the muzzle. I went ahead and ordered 2 more 37" blanks from Schneider Barrels last week that are their blackline custom contour which is 1.350 for 6.5" then tapered to 1.2" at the muzzle.

I thought you could get a 1.350 straight in there can't you? What is making you want more clearance than a muzzle diameter of 1.1 isn't accommodating?
 
#23,823
Bacarrat said:
What parts are hard to get for the MC? Bolts aren't that bad. I waited for a WM bolt, but they look to be available right now. Firing pin assemblies are easy enough to swap over, even then you can buy a extra one pretty easily.
Click to expand...

I'm almost 9 months into waiting for a #27781 1.6mm SFP 338L AXMC bolt body. There were a couple in stock at Euro in December of 2024 and I snoozed a couple days before ordering; a week later when I went to order they were out of stock. I have one backordered, but at this point I've accepted AI might discontinue it. Mile High no longer has that part number listed on their website, a few months ago the page for it was still there but showed out of stock.
 
#23,824
Roadrace33 said:
So mine is a 36" , 1.350 for 6" then tapered to 1.1 at the muzzle. I went ahead and ordered 2 more 37" blanks from Schneider Barrels last week that are their blackline custom contour which is 1.350 for 6.5" then tapered to 1.2" at the muzzle.

I thought you could get a 1.350 straight in there can't you? What is making you want more clearance than a muzzle diameter of 1.1 isn't accommodating?
Click to expand...
I have a 34” 33XC that was 1.35 x 5 then a straight taper to 1.1 at the muzzle and with a little bit of load on the handguard it would touch. It measured about 1.28 where it would touch so I had it re-contoured to 1.2 to give ample clearance.

My factory handguard was a tighter fit than the M-Lok version so I swapped those as well.
 
#23,825
ReturnFire said:
I have a 34” 33XC that was 1.35 x 5 then a straight taper to 1.1 at the muzzle and with a little bit of load on the handguard it would touch. It measured about 1.28 where it would touch so I had it re-contoured to 1.2 to give ample clearance.

My factory handguard was a tighter fit than the M-Lok version so I swapped those as well.
Click to expand...
HMM, i wonder if i should see if they have a slightly lighter taper or do you think this will work? I imagine it is close.
 

Attachments

  • IMG_1535.jpeg
    IMG_1535.jpeg
    360.3 KB · Views: 26
#23,826
Kiba said:
I'm almost 9 months into waiting for a #27781 1.6mm SFP 338L AXMC bolt body. There were a couple in stock at Euro in December of 2024 and I snoozed a couple days before ordering; a week later when I went to order they were out of stock. I have one backordered, but at this point I've accepted AI might discontinue it. Mile High no longer has that part number listed on their website, a few months ago the page for it was still there but showed out of stock.
Click to expand...
9 months isn't too bad. I found a WM bolt after 2 years of somewhat looking. NikH waited 4 years for his left hand bolt. You can always get a LFP bolt and have it redone for a SFP. While we can bitch and cry about parts availability, there are worst platforms to get parts for(Knights). You have to remember the lowly civilian is last on their priority. That goes with a lot of stuff in the shooting arena.
 
#23,827
Roadrace33 said:
HMM, i wonder if i should see if they have a slightly lighter taper or do you think this will work? I imagine it is close.
Click to expand...
I’d go lighter but that’s just my opinion. I had to have Fritz cut mine down in order for it not to touch. This was how it looked before it was re-contoured.
 

Attachments

  • IMG_6345.jpeg
    IMG_6345.jpeg
    1.1 MB · Views: 54
  • IMG_6344.jpeg
    IMG_6344.jpeg
    1 MB · Views: 53
  • Like
Reactions: BCX and Part Timer
#23,828
ReturnFire said:
I’d go lighter but that’s just my opinion. I had to have Fritz cut mine down in order for it not to touch. This was how it looked before it was re-contoured.
Click to expand...
Ahh ya that is tight. Ill see what they have for a step below, or else ill have fritz re contour it. My current 37xc barrel came from bugholes as 1.450, and he made it work.
 
#23,829
Roadrace33 said:
So mine is a 36" , 1.350 for 6" then tapered to 1.1 at the muzzle. I went ahead and ordered 2 more 37" blanks from Schneider Barrels last week that are their blackline custom contour which is 1.350 for 6.5" then tapered to 1.2" at the muzzle.

I thought you could get a 1.350 straight in there can't you? What is making you want more clearance than a muzzle diameter of 1.1 isn't accommodating?
Click to expand...
I don’t believe you can get a straight 1.350 contour in a AXSR forend. Someone here correct me if I’m wrong. 1.250 at the muzzle end of the forend is the largest I have tried.
 
#23,830
  • Like
Reactions: Nik H
#23,831
BCX said:
I don’t believe you can get a straight 1.350 contour in a AXSR forend. Someone here correct me if I’m wrong. 1.250 at the muzzle end of the forend is the largest I have tried.
Click to expand...
Kopfjager1 said:
I recommend going 1.19" @ 28" with 1.350"x5" shank to be below 1.250" at the end of the forend (for a straight taper).

Or with a 1.350"x3" shank: 1.17" @28".
Click to expand...
Technically 1.27" will fit at the end of the forend (16"), but I would still aim for 1.25", which would be 1.16" at the muzzle for a 37" barrel, 6" shank.
 
  • Like
Reactions: BCX
#23,834
I mean I’m not going to be rucking up any mountains, purely benchrest, but this thing is ridiculously awkwardly long 😂 chopping the barrel is definitely going to be considered. Gonna shoot it, see how it is first. Who knows.

In all honesty I bought it with the intentions of grabbing an AX ELR in the future. But it’ll sit on the SR for the time being.

The one pic is a comparison to the TBAC 338 Ultra G2.
 

Attachments

  • IMG_3802.jpeg
    IMG_3802.jpeg
    187.8 KB · Views: 127
  • IMG_3808.jpeg
    IMG_3808.jpeg
    187.1 KB · Views: 128
  • IMG_3807.jpeg
    IMG_3807.jpeg
    202.4 KB · Views: 105
  • IMG_3811.jpeg
    IMG_3811.jpeg
    166.5 KB · Views: 104
  • IMG_3809.jpeg
    IMG_3809.jpeg
    210.7 KB · Views: 123
  • Haha
  • Wow
  • Like
Reactions: kthomas, leftyk82, JonKleman and 10 others
#23,835
Roadrace33 said:
I mean I’m not going to be rucking up any mountains, purely benchrest, but this thing is ridiculously awkwardly long 😂 chopping the barrel is definitely going to be considered. Gonna shoot it, see how it is first. Who knows.

In all honesty I bought it with the intentions of grabbing an AX ELR in the future. But it’ll sit on the SR for the time being.

The one pic is a comparison to the TBAC 338 Ultra G2.
Click to expand...
Good god. I guess you don’t have to dial if your barrel and suppressor are so long they are halfway to the target.

That’s definitely got to slow down your ADS speed. No quick scopes for you.

That’s seriously sick though. I’d love to hear what it sounds like shooting a 37XC, so I can live vicariously through you.
 
#23,838
Watch_this71 said:
Why do I hear 70's porn music when I look at that last pic?
Click to expand...
Dude this house was built in the 70’s, I literally just got rid of the GREEN shag carpet last fall 😂

Whole house had shag carpet. Bathrooms too.

80’s hair bands are all that plays in the basement…
 
Last edited:
  • Haha
  • Love
  • Like
Reactions: Aerem, Huskydriver and Watch_this71
#23,839
Roadrace33 said:
I mean I’m not going to be rucking up any mountains, purely benchrest, but this thing is ridiculously awkwardly long 😂 chopping the barrel is definitely going to be considered. Gonna shoot it, see how it is first. Who knows.

In all honesty I bought it with the intentions of grabbing an AX ELR in the future. But it’ll sit on the SR for the time being.

The one pic is a comparison to the TBAC 338 Ultra G2.
Click to expand...
Tac ops can hook you up with a case

A 97” drag bag should work
 
  • Haha
  • Like
Reactions: TheJeanyus, taliv, Roadrace33 and 3 others
#23,842
DKN83 said:
View attachment 8747191
🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣

"Fellow hide members during a competition 2025 using their AIs after they ran out of ammo"
View attachment 8747192
Click to expand...
You think I'd get any funny looks if i show up to the next PRS match and whip this thing out? I might have to just bring it and try and keep a straight face during sign in. Ill have to load it up on my 53' stepdeck, it isn't gonna fit in the fucking denali. Boy i hope there are no standing positions...
 
  • Haha
Reactions: kthomas, TheJeanyus, Nik H and 2 others
#23,843
Roadrace33 said:
You think I'd get any funny looks if i show up to the next PRS match and whip this thing out? I might have to just bring it and try and keep a straight face during sign in. Ill have to load it up on my 53' stepdeck, it isn't gonna fit in the fucking denali. Boy i hope there are no standing positions...
Click to expand...
You need to show up with it on a trailer and strapped down.
 
  • Like
Reactions: Roadrace33
#23,845
Roadrace33 said:
You think I'd get any funny looks if i show up to the next PRS match and whip this thing out? I might have to just bring it and try and keep a straight face during sign in. Ill have to load it up on my 53' stepdeck, it isn't gonna fit in the fucking denali. Boy i hope there are no standing positions...
Click to expand...
Yeah I think that barrel length negates the precision aspect, just turns into close quarters.
 
You must log in or register to reply here.

Similar threads

Mj30wilson900
Accuracy international aics retrofit
Replies
4
Views
299
Kiba
K
Raptorman2014
Firearms New Accuracy International AXSR FDE 300 PRC
Replies
4
Views
887
Raptorman2014
Raptorman2014
austino775
The AI Arctic Warfare Picture Thread
Replies
266
Views
22K
IK6243
IK6243
R
Accuracy international 2.0 legacy stock pricing?
Replies
10
Views
828
Duckhunter666
Duckhunter666
J
SOLD Accuracy International AT-X Gen 3 New
Replies
5
Views
1K
Prize9678
P
Top Bottom
Back
Home
Forums
Merch
Alerts