Recent content by crashandburn

  1. C

    Phoenix Custom Rifles 7 mag

    Re: Phoenix Custom Rifles 7 mag That is one clean rifle right there Brad! Great work as always. Gotta say I'm diggen the stock too, that color scheme looks RAD! If you're thinking of having a rifle built or looking to have a rifle built give the guys at PCR a shout. You can't go wrong.
  2. C

    Gunsmithing CDI v Badger M5

    Re: CDI v Badger M5 Badger! Wouldn't go with CDI unless I owned a rifle that only CDI made the DBM for.
  3. C

    Looking to Build a 18.5" rifle

    Re: Looking to Build a 18.5" rifle I have a New Trued remington M700 SA (SPS) , New Krieger 5R barrel 1:10 varminter which can be cut, crowned and threaded by Phoenix Custom Rifles. I have a Like New Trued Remington M700 SA (LTR) with a Krieger 1:12 tight bore in medium palma (similar to...
  4. C

    Looking to Build a 18.5" rifle

    Re: Looking to Build a 18.5" rifle PM sent. May have what you're looking for.
  5. C

    Gunsmithing need a smith to install pillars

    Re: need a smith to install pillars Keith Johns @ Phoenix Custom Rifles.
  6. C

    Gunsmithing conventional mill cutter speed for stock inletting

    Re: conventional mill cutter speed for stock inletting I used a 3/8 4 Flute Carbide End mill with an extended shank and ran it about 1000rpms (could go faster), worked fine. Just don't run your feed too fast. My 2 cents
  7. C

    Gunsmithing Reworking my Howa, NEWCDI DBM LEVER!

    Re: Reworking my Howa, UPDATED! Made myself a new lever for CDI DBM! check it out. Similar to the Surgeon style and can be used by either hand. It feels better and works better IMO. Befor! After! I repositioned the spring dimple on the lever to keep the spring horizontal, makes it feel...
  8. C

    Gunsmithing just some pictures from this weekend's shop time.

    Re: just some pictures from this weekend's shop time. Great pictures and damn good work sir. I enjoy seeing other people's methods and outcomes. Keep it up!
  9. C

    Gunsmithing Reworking my Howa, NEWCDI DBM LEVER!

    Re: Reworking my Howa, UPDATED! Thank you sir. I hope to have this one tested soon with a a good range report to follow.
  10. C

    Gunsmithing Ejection/Extraction Problem Rem 700, PTG bolt

    Re: Ejection/Extraction Problem Rem 700, PTG bolt I had the problem of the brass hitting my scope turret then going back in with a factory extractor. Keith lengthened my ejection port so the brass had a chance to get out sooner, haven't had that happen since.
  11. C

    to go 260 remington, or stick with 308

    Re: to go 260 remington, or stick with 308 GO 6.5 CREEDMOOR !
  12. C

    Gunsmithing Reworking my Howa, NEWCDI DBM LEVER!

    Re: Reworking my Howa, Remington and Mauser bottom metal design IMO. Its just a little thicker there. The DBM sits nice and flush, the action sits right where it should. If you dropped one end down it would tilt the DBM which seems level from end to end so it might mess with feeding. When you...
  13. C

    Gunsmithing Reworking my Howa, NEWCDI DBM LEVER!

    Re: Reworking my Howa, Remington and Mauser the Bottom metal sits flush and looks good all the way arounds but the trigger gaurd is a little too thick for my taste. With some minor machining it should feel and look great.
  14. C

    Gunsmithing Reworking my Howa, NEWCDI DBM LEVER!

    Re: Reworking my Howa, Remington and Mauser Here are some pictures show some of the differences in design. The surgeon, notice the angles machined at the top of the latch. The A.I, again notice the area above the lever. A.I has the chassis behin the mag well just slightly so the mag...
  15. C

    Gunsmithing Reworking my Howa, NEWCDI DBM LEVER!

    Re: Reworking my Howa, Remington and Mauser Keith I'd rather not drop the DBM deeper than flush, thats where it needs to be IMO. The gaurd just needs some minor material removed which should be no problemo. If I inlet deeper I have to redo the latch and everything els to get the fit it has...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts