Recent content by neutronics

  1. neutronics

    Why I don't go to gun shows

    Re: Why I don't go to gun shows About 10 years ago, when I first started getting serious about firearms I went to "the Costa Mesa show," which is more or less THE show to go to in Southern California. While in there, there was a guy with a sign over his table that said something to the...
  2. neutronics

    Gunsmithing Place to get good Steel

    Re: Place to get good Steel +1 for onlinemetals.com. Selection is so-so but the prices and delivery are good. I've had good luck buying cut-offs on eBay. Mostly bar stock in lengths less than a foot sold by the pound.
  3. neutronics

    Anybody use the Candlepower forums?

    Re: Anybody use the Candlepower forums? I've been a member there for a number of years and have seen it go through several different iterations. And you're right, it does seem to get a bit more confusing each time. I don't visit there too often any more because most of the posts are people...
  4. neutronics

    Rifle Scopes Mounting Help?

    Re: Mounting Help? Alternative to measuring everything you can clamp the rifle in a vise and point the crosshairs at a mark on the wall. Then start flipping and/or reversing the rings, remount the scope and see if the POA changes. If you only have a caliper you might want to have a smith...
  5. neutronics

    Osama Bin Laden Kyhber AKM *Range Target Photo*

    Re: Check out my Osama Bin Laden Kyhber AKM *Photos* Nice rig! I've always wanted an authentic AK like that. Unfortunately in Cali they are a little hard to come by. (And if you can find a dealer willing to transfer one to you they're $$$$.)
  6. neutronics

    Installing a Ops. Inc. Brake and collar?

    Re: Installing a Ops. Inc. Brake and collar? <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Blackops_2</div><div class="ubbcode-body">I'm getting close to ordering my BCM 18" MK 12 Mod 1 upper with the KAC RAS. Since noone has the Ops Inc. brake and collar in and...
  7. neutronics

    Rifle Scopes Mounting Help?

    Re: Mounting Help? It might be possible to get closer to true by rearranging your rings. Swap the front and rear, reverse the front and/or rear, etc. Do you have access to measurement tools or access to a friend that can check it out for you? I would think this is preferable to randomly...
  8. neutronics

    Gunsmithing Sand blasting with a smaller compressor?

    Re: Sand blasting with a smaller compressor? My blasting setup has a 60 gallon. It is adequate, but if you’re really hogging material or using a mild abrasive the compressor runs continuously. The pressure seems to hold up though, but the compressor tank gets hot enough to freak me out a...
  9. neutronics

    Gunsmithing VISE

    Re: VISE I have the Grizzly version and really like it. Prior to that I had a Harbor Freight drill press vise mounted to my bench. The mounting block allowed you to put the jaws parallel or perpendicular to the bench top. Super-duper handy, which is why I later switched to the Grizzly...
  10. neutronics

    Anybody played with a NovaTac light?

    Re: Anybody played with a NovaTac light? NovaTac is an "okay" product. The way they heatsink the LED is not very good though. Surefire's heatsinking is not very good either, but it's better than NovaTac. If you break or otherwise dispose of lights frequently this will be less of an issue...
  11. neutronics

    Gunsmithing Need help with a big Enfield project

    Re: Need help with a big Enfield project <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: DarKnight</div><div class="ubbcode-body">Update us on this project, Neut </div></div> No movement yet. I'm having a hard time tying it all together. I wouldn't mind doing...
  12. neutronics

    Gunsmithing Need help with a big Enfield project

    Re: Need help with a big Enfield project Hi guys, thanks for all the replies, I really appreciate it. It is a P17 Eddystone. Here are some pics. BTW it is chambered for .30-06 so far as I can tell; a .30-06 cartridge fits into the chamber and into the boltface (I did not close the bolt)...
  13. neutronics

    Gunsmithing Need help with a big Enfield project

    Didn't find anything on search; tried posting to my local smiths (at calguns.net) but no results!! Here's the situation. The gun belongs to my uncle, who is an old war-horse that served in Korea and Vietnam. He's in his 70s and feeling his mortality. He has an Enfield that's been a work in...
  14. neutronics

    Questions about my savage .308

    Re: Questions about my savage .308 Hard to say with such a short description. I have a 10FP also and never any issues with FGMM ammo. Had some Prvi Partizan rounds that didn't want to chamber however (bullet was already into the bore before bolt was closed). If you have the tools to...
  15. neutronics

    Suppressors XD45 with 200gr LSWC feed problems

    Re: XD45 with 200gr LSWC feed problems Make sure the bullet isn't touching the inside of the slide stop. Some of the Remington hollowpoints do on my XD45.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts