• Watch Out for Scammers!

    We've now added a color code for all accounts. Orange accounts are new members, Blue are full members, and Green are Supporters. If you get a message about a sale from an orange account, make sure you pay attention before sending any money!

Search results

  1. F

    Gunsmithing Thread Adapters

    Who is making and selling custom thread adapters. Been off here for a while and do not remember the board members name.
  2. F

    Hunting & Fishing Public land Hog hunting Houston Texas

    Re: Public land Hog hunting Houston Texas Get a $48 permit from Texas Parks and Wildlife Office, not walmart, so you can get the WMA book that has all the locations and maps across Texas. A lot of places to hunt and read the rules for each location.
  3. F

    Hunting & Fishing Subsonic Meat Test (pic heavy)em

    Re: Subsonic Meat Test (pic heavy)em Good write up with pics. I use the Horn 220gr RN for AR 762x39, 308, and 300 Firball for hogs Most shots go for the head and second hog is at shoulder with good results. I have also used 200gr spitzer. I had posted pics of a 200gr exit on a hog. The...
  4. F

    Hunting & Fishing 458 Socom Sub-Sonic

    Re: 458 Socom Sub-Sonic Bulk Rem 405gr FP with 15gr Trail Boss @ 975fps. My 16" bolt gun likes Rem 405gr with 13.2 Unique @ 1025. I started with 510gr but these are less than half the price. Good for target and gets the job done on the pigs. The suppressor is my Form 1. Not as quiet as...
  5. F

    Hunting & Fishing 458 Socom Sub-Sonic

    I got these two tonight and saw a 300lb.+, but he eased back into the weeds before I could get close enough, He looked as big as some of the black cows when laying down.
  6. F

    Gunsmithing New parts washer, Need solvent advice

    Re: New parts washer, Need solvent advice Naptha is also used for parts cleaners. you may have to get it at fuel & oil distributors.
  7. F

    Gunsmithing AR-15 burst firing? Need Advice!

    Re: AR-15 burst firing? Need Advice! The cam action of the carier-bolt retracts the protrusion of the firing pin. Sounds like springs or a bad disconnector letting it bump fire vey easy.
  8. F

    Quickload

    Re: Quickload Well, thanks for the info, good or bad. I guess I will have to do trial and erra like I have done with some of my sub-sonic loads. I will start a little long and cut, till I have gone a little to far. Thanks Eddie
  9. F

    Quickload

    Could someone with Quickload or similar, run a load to find out bullet travel to burn all the powder. 458 Socom, 405gr FP, 13.2gr Unique. A 16" barrel is giving me 1025 vfs Suppressed. I am doing a barrel for my SBR and trying to figure a good length. Thanks.
  10. F

    Crooked brass in station 5 on my Hornady LNL AP

    Re: Crooked brass in station 5 on my Hornady LNL AP What case lube are you using to run the rifle brass progresive?
  11. F

    Feedback Good Guy List

    Re: Good Guy List 7.62Texan deliverd the new scope as agreed. So he is GTG Thanks
  12. F

    Gunsmithing End Mills

    Re: End Mills Something around a 9x36, power feed table and head, with coolant system prefered, do not need DRO. Thanks for the replies, Eddie
  13. F

    Gunsmithing End Mills

    Re: End Mills Thanks RAD, I am doing other searches.
  14. F

    Gunsmithing End Mills

    Re: End Mills I am looking for the WTS add that had 2 vertical Mill Machines. I don't remember if they were Bridgeport ect. Thanks
  15. F

    Gunsmithing Barrel Length for .30-06 1000 yd shooting

    Re: Barrel Length for .30-06 1000 yd shooting + 10 for honesty, it can happen , murphies law!!
  16. F

    Gunsmithing End Mills

    Who had the post with the 2 verticle mills for sale 3 or 4 months ago, I am not having any luck with the search? Thanks Eddie
  17. F

    Gunsmithing Silver Soldering Barrel Nut?

    Re: Silver Soldering Barrel Nut? Seems the torque sequence of the action to the stock can make some POI changes, as you have to remove stock to use your wrench.
  18. F

    Gunsmithing Chrome Lined Bore

    Re: Chrome Lined Bore jwSubMOA, are you refering to the brazed-on carbide tooling or carbide tool stock? Are you parting off a little long and machining back to measurment? I have 4 different types of tooling. For Chrome Moly and Stainless crowns, I like the HSS tool stock. ((( I have...
  19. F

    Gunsmithing Chrome Lined Bore

    Re: Chrome Lined Bore I have a tool post grinder and thought if I did not hear of any good ways I could use a cutting disk on it and a cone rock for dressing an angle on the bore or round rock for a square crown. What do you think? It would take a lot more time this way. Thanks for info.
  20. F

    Gunsmithing Chrome Lined Bore

    What is the best way to cut a chrome lined bore and not risk chipping? I have read they could be trouble!