change

$300 USD SHIPPED All items are NIB. Selling as a package. -Lee Precision Classic Cast Single Stage Press -Inline Fabrication Tall Ultra Mount W Quick Change Base -Inline Fabrication #17 Quick Change Plate -Inline Fabrication Case Ejector System W Side Bins (Bin Barriers Not Included) Payment...

Hi guys, I have a question about hand loading. Finally, after much labor, I have developed a hand load that gets a certain gas gun to hold 1/2 MOA. All of the load data and experimentation was done with Remington brass, but now much of that brass has passed it's useful lifespan. Now that...

Oil Change instructions for Women: 1) Pull into your nearest "15 Minute Oil change" when the mileage reaches 3000 miles since the last oil change. 2) Drink a cup of coffee 3) 15 minutes later, write a check and leave with a properly maintained vehicle. Money spent: Oil Change: $20.00 Coffee...

This is a long read but this is an ALL TIME CLASSIC! Jason Lu...(aka Smokin here on the Hide) man you are a great sport and if we didn't like you as much as we do ...we wouldn't screw with you like we do. The best thing about this was it wasn't planned at all. Jason B (aka 4thSeal) just...

I NEED 7mm Amaxs and can only find moly coated ones. Will these make a significant change from the standard bullet? Can the moly be removed? Thanks

I was wondering if I should bother changing the barrel on my 700p. I have fired under 200rds through it and it fires .5moa all day long and have had some better grouping using handloads. Currently I use m118lr and FGMM 175 factory ammo through it. I like the idea of being able to clean it...

I tried my hand at annealing yesterday and I think it turned out pretty good. I had some 6.5-284 brass that had been reloaded 7 times and I had started getting a few split necks so I figured what the heck, the cases weren't going to be any good anyway. Went to range today and I picked up 30 fps...

seems like the last time I loaded some rounds was March and I am just getting to shoot some distance again. Loads are 168gr Match 45.5gr Varget@2765. only get to shoot to 500yds. 100yds still 0, but walking out it was increased to 4.5 to 5 MOA less dial in today. Varget is supposed to be...

I got an AIAW and a looking at brownells fro a good barrel action block that I can just clamp in my bench vice. there are so many barrel vices listed that I dont really know what im looking for. Does anyone have hand good suggestions. My vice is standard 4". can I also use a set of brownells...

I have been shooting for a while now and finally upgraded my scope to a nightforce with 20 moa base and zeroed at 100 yds. With my old scope (nikon buckmaster 4.5-14)also zeroed at 100 yds, it took 8.5 moa to get to 500 yds. Now with my new setup it only took 6 moa. Around the same temp...

I was reviewing my log book and over the last three months and 500 rounds, my zero has moved 6.25 MOA right and 1.75 MOA up. Comparison was taken at the same shooting "range". Temp started at 49.5 degrees to last night of 80.5 degrees. Density altitude has moved from around 7100 to 7550 as it...

Alright everybody, just like the title says how do I change a barrel? I've been looking around and I can't find a tutorial or video or anything on the process of changing a barrel. Could somebody point me in the right direction. The rifle is a tikka if that helps. Thanks!

I will be changing a barrel in my AIAW. How do you change the barrel without leaving a shinny barrel holder mark on the barrel.

Is it normal to have defferent points of impact when shooting from sandbags and then going to a bipod? Jim

I've got a 7mmRM with a 26" and am thinking of cutting it down. I currently reload for this rifle with 65gr of RL22 behind 168gr VLDs. I'm thinking of cutting back to 20" and putting a can on it. Will I still be ok, or will I need to switch to a faster burning powder? I just don't want to end up...

How difficult is it to change a barrel on a tikka rifle?

A buddy of mine has a Leupold Mark 4 4.5-14x50 LR/T with .5 centimeter adjustments. My question is can we get a 1 centimeter turret put in this scope?

This weekend I was load testing and fired 50 rounds, 5 shots each, per .1 grain of powder. I came up with an odd result. All rounds were loaded in the same sitting from the same batch of once fired fully prepped brass, that was also prepped in the same sitting. All shooting was done in the...