reloading

I'm loading 77gr SMKs to mag length (2.6") but I'm getting variations between 2.55" and 2.60". Is there anything I can do make this a more uniform process? Below is my process. 1. Tumble once fired brass (RP in this case) 2. Resize and deprime 3. Trim cases to length (Layman hand trimmer) 4...

Looking for the below. Powders: H1000 - Any Weight H4350 - Any Weight FED215M - Any Qty 6.5 creedmoor bullets - I prefer Hornady 140gr ELDM 300 Norma Mag - bullets and brass Located in CA. I will pay to ship.

I am looking to trade 8 pounds of alliant powder 23 for h4350, primers or let me know what you have. I am in Ohio near Cleveland

Just 30-06 loads I’m just getting into long range shooting and I was hoping for some help. I have a 24” barrel with a 1:10 twist. Just wanting to work up some good loads and was hoping to be pointed in the right direction. ie bullet grain and type, type of powder and primer. thanks in advance

$35 net to me plus shipping from 50613.

I have an unopened 8lbs keg of RL26 I want to trade for N565 in indiana. Purchased in October 2020 and has sat in my living room since. The only other thing I'd consider trading for is 450s. Not looking to sell.

Most of us have several stacks of carefully reloaded and labeled rifle ammo that we thought was the correct ammo to reload during a brief interlude of mindlessness. Now we find that we have several loadings for a same rifle with some feature (bullet weight, OAL, powder, muzzle velocity, etc.)...

Hi Everyone, I think this wheel I made might be useful if you also find it difficult to draw the correct combination of disk-holes for Lee Auto Disk setups. Here is the project LeeAutoDiskChart and generated results attached. It was using Lee published VMD to generate all possible powder charges...

I have accumulated a bunch of .223 brass I want to load for my SIL - mostly practice / plinking rather than precision loading. Its mixed brass and has a good bit of crimped brass in there. I've never dealt with crimped brass previously and want to see what the best option would be. I recently...

I have some 220 Swift RCBS dies I’m looking to sell. http://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=2&pub=5575378759&campid=5338273189&customid=&icep_item=402639762521&ipn=psmain&icep_vectorid=229466&kwid=902099&mtid=824&kw=lg&toolid=11111

This is my first time reloading Large Rifle Primers. Using Federals. Shot during powder charge tests. First round fired, next two didn’t! I then moved on to heavier powder charge and same damn thing. 2/6 cartridges fired. The ones that didn’t fire are severely caved in and obviously have a...

Just as title says I’m looking to buy a set of 22br type a full length die set u can contact me at (931) 310-1325 thanks

Hey guys, so I’m relatively new to reloading and have a couple questions. 1: 6.5 Creedmoor powder. Everyone is dealing with the powder/primer crisis, but I’ve been able to get my hands on 8lbs of H4350 which I plan on using in my 6mm Creed, but also have 8lbs of H380, 2 lbs of IMR 4350, and 8...

Hello guys! So I am new to reloading, I have been obtaining my reloading equipment and the supplies I can find to start reloading and so far I have managed to get the following items to start reloading with: ADG 6.5 creedmoor LRP brass Nosler RDF 140 grain .264 bullets Hornady ELD-M 130 grain...

Anyone else notice the prices jumped on the Hodgdon website or is it just me? What was once 26-30$ is now about 40$. I wonder if all these prices will drop again once everything starts to calm down or if they’ll remain the current fixed.

I’m new to reloading and I’m soon going to start reloading some .338 Lapua and I read about neck sizing and bumping the shoulders back. I know the neck sizing is done on a single die, but is there a die specifically for shoulder bump? Or is it bumped with a FL sizing die? I’m just lost on this.

Looking for pregressive press, dillon, Hornady, Lee. Looking to load 9mm. I have dies. Have for trade: GOLD triggertech two stage diamond, red single stage diamond, powder h4350, berger 7mm 195s, 338 eldm 285 gr, etc. Please let me know

Shot a little in a field around July and today I went back to pick up any brass that might be laying around. I’ve picked up about 50 cases so far. Some on top of the dirt, some half buried. They look a little dark, not that nice new brass color, no signs on corrosion on most of them. Any reason...

Needing some assistance with the recommended order to place my dies in my turret, by order of operations? I’ve got the Area 419 Zero Press w/ 9 turret spaces. Currently only reloading for a 6.5 Creedmoor. In possession #1 is my Mighty Armory decapping die. Here are the others that I have and...