• Watch Out for Scammers!

    We've now added a color code for all accounts. Orange accounts are new members, Blue are full members, and Green are Supporters. If you get a message about a sale from an orange account, make sure you pay attention before sending any money!

**6 Creedmoor**

29 grains seems to be doing better groups and believe it or not less recoil I know that might sound funny but .5 Les grains of powder I can actually tell less recoil I might even go down 28.5grains of h4350. 29 grain muzzle velocity is 2920 can't wait to try it out at the further distances might be able to get to three hundred yards. the weather is in the 40s in Ohio it was in the 9° range last week too cold for me. 29.0grns works great fore 115 dtacs last year.
 
New match rifle. I know, I know: it’s only 3 shots, but it still ain’t bad! 30 rds on the barrel. Not sure of the exact velocity but from everything I’ve read here it should be around 3k. 26” 7.7 twist barrel. GAP reamer (I think it’s .199 freebore).

Edit 1.1.20: Alpha SRP virgin brass, 41.5 H4350, CCI 450, 110 Atip, 2960fps, SD: 8. 2.241” bto. 65 rds down the barrel.

UPDATE 03.09.20: 263rds down the barrel. Velocity has settled in at 3055fps average over 10 shots with an SD: 4.4 on 1x fired brass. Still shooting lights out.
 

Attachments

  • 2B14783C-55D7-440B-BF6C-4B7877A3C848.png
    2B14783C-55D7-440B-BF6C-4B7877A3C848.png
    4.5 MB · Views: 173
Last edited:
  • Like
Reactions: rcorby2
Good reading
The article is pretty spot on, but left out some key details. I dumped 6mm creedmoor due to 2 things: barrel life and chasing the lands for accuracy. I never had "bad accuracy" with my barrel, but you have to constantly chase the lands with the round as it is kind of a barrel burner. For most I’m sure that doesn’t matter, but the round gets expensive when you factor in the cost of the barrel over 800-1200 rounds.
 
Just ordered a 6 Creed barrel for a coyote rifle. Is an 8 twist too fast for a 75 grain bullet at 6 Creed speeds? I'll probably shoot the factory 87 vmax ammo but just curious of other options.
 
Been running 41.5 grains of H4350 for a while with the 108’s. 41.5 has me slinging them @ 3130.

Backed it off a grain and shot two groups with 40.5. Just a tad bit slower (3050) but will save some brass/barrel life. 26” Proof Stainless.
2249AC1C-EF06-4103-9031-85188C8799D3.jpeg
 
I'm waiting patiently for my 6CM to be finished. Heavy Palma Krieger Barrel, cut down to 28". Building off a 700Rem action. Keystone Tactical Stock. Plan on 87gr and 105gr bullets. It will be fun finding the load that works for it. Maybe by the time its done it will be warm enough to go shoot. Weather has been all over the place here in Eastern Mt. Thanks for all the load info you all posted!!
 
  • Like
Reactions: Trapper1956
ADG brass, I skimmed the necks because they were a little too thick and hung up in my Whidden seater die.

Anyway, after forming all 100 pieces of new brass my final load in my 24” Brux is...
1X Fired ADG Brass
40.4 H4350
210M
105 Berger hybrid .020 jump
3110 FPS

My other load...
Hornady 6.5 creed brass necked down
42 H4350
210M
108 eldm .030 jump
3105 FPS
 
  • Like
Reactions: Lunchbox27
Hell yah it is! I'm running 40.6 with 108's and a suppressed 26" and I'm 3060fps
 
The ADG is about 30 grains heavier and holds about 5 grains less water than Hornady.
 
  • Like
Reactions: 47guy
Re: **6 Creedmoor**

how close is this cartridge to a 6 XC?

6 Creedmoor and 6XC are almost EXACTLY the same. Look at the reamer prints an it will be obvious to you. It is kind of a scam to call them two different cartridges.
-TH
 
Just starting to do load work on a Deviant action with an 8 twist Krieger barrel. Not sure on throat or freebore, since this was used when purchased. My question is for anyone that has done testing on Alpha large and small primer brass with 7-10 firings on the brass. Does there seem to be a difference on how tight the pockets stay, and how much difference have you noticed in velocities with similar bullet weights? I want accuracy over speed, but part of the reason for buying the 6 CM was to get more velocity over the 6BRA or Dasher that I use for competitions. I'm starting out testing both R17 and H4350 in both large and small primer brass. Small primers are CCI 450's and large are 210 Match. I have other primers to test, but this is where I'm starting.
 
Another question; in the process of ordering a reamer for a couple barrels. My plan is to set these barrels up for shooting 95-105 grain bullets. Most of the bullets will be hunting bullets, with occasional comps in hunter class target matches. What have you found is the best freebore for this weight of bullets? I will be mainly using Berger hunting vld's, with an occasional Swift Scirocco 90 grain thrown in.
 
A few months back when H4350 was hard to get I tested some really old IMR4831 in my 6 creed it shot great.
I went through the 2 pounds I had of the old powder then grabbed a few pounds of new production IMR4831 and it was
just as good.
Its a bit faster then the Hodgon equivalent and definitely worth a look as its always available.


42.7 IMR4831 (cira 1984)
105 hornady bthp
CCI 450
Lapua brass
24" RPR

Stats - Average 3028.17 fps
Stats - Highest 3034.53 fps
Stats - Lowest 3023.36 fps
Stats - Ext. Spread 11.17 fps
Stats - Std. Dev 4.48 fps

Shot ID V0 V10
1 3035 3006
2 3031 3009
3 3025 3006
4 3028 3008
5 3023 3004


42.8 IMR4831 (New Production)
105 hornady bthp
CCI 450
Lapua brass
24" RPR

Stats - Average 3016.9 fps
Stats - Highest 3027.7 fps
Stats - Lowest 3006.61 fps
Stats - Ext. Spread 21.09 fps
Stats - Std. Dev 6.63 fps

Shot ID V0 V10
1 3007 2985
2 3020 3000
3 3018 2996
4 3024 3005
5 3019 2997
6 3010 2990
7 3013 2994
8 3019 2999
9 3011 2992
10 3028 3009
 
A few months back when H4350 was hard to get I tested some really old IMR4831 in my 6 creed it shot great.
I went through the 2 pounds I had of the old powder then grabbed a few pounds of new production IMR4831 and it was
just as good.
Its a bit faster then the Hodgon equivalent and definitely worth a look as its always available.


42.7 IMR4831 (cira 1984)
105 hornady bthp
CCI 450
Lapua brass
24" RPR

Stats - Average 3028.17 fps
Stats - Highest 3034.53 fps
Stats - Lowest 3023.36 fps
Stats - Ext. Spread 11.17 fps
Stats - Std. Dev 4.48 fps

Shot ID V0 V10
1 3035 3006
2 3031 3009
3 3025 3006
4 3028 3008
5 3023 3004


42.8 IMR4831 (New Production)
105 hornady bthp
CCI 450
Lapua brass
24" RPR

Stats - Average 3016.9 fps
Stats - Highest 3027.7 fps
Stats - Lowest 3006.61 fps
Stats - Ext. Spread 21.09 fps
Stats - Std. Dev 6.63 fps

Shot ID V0 V10
1 3007 2985
2 3020 3000
3 3018 2996
4 3024 3005
5 3019 2997
6 3010 2990
7 3013 2994
8 3019 2999
9 3011 2992
10 3028 3009
Thanks, good to know there are options out there. It looks like that old lot was some good shit. I have several 8 lbers of H4350, since it gets used for my 1000 yard competition rifle. I'm testing the R17 just to see if there is a little more velocity with safe pressures.
Did you try any other primers besides the 450's? I figured with the small pockets, it would be best to see if a magnum primer gives me better ignition with the amount of powder that is used.
Cheers
 
I only use 450's for my small primer loads, they give me low SD numbers and have been 100% reliable so no reason to look for better.
 
  • Like
Reactions: MilSpecOkie
I have finally had a chance to do a bit of testing with R17 and H4350 with the Berger 105 hunting VLD. My reason for this bullet is that it will be a long range hunting load for red deer and pigs in New Zealand where I live for part of the year.
I found H4350 to be a better choice than R17 in my rifle from an accuracy standpoint. I finally remembered my labradar yesterday so I could get some velocity readings to go with accuracy tests. My barrel must be fairly slippery compared to some of the velocities I have seen here. I averaged 3125 with 40.7 grains in a 5 shot sequence, with an ES of 12 and SD of 6. 41 grains averaged 3128 with an ES of 24 and a SD of 13. No hard bolt lift, but one of the 450 primers blanked on me at 41 grains, so that is telling me that 40.7 is about it for this combo. Both loads are a little under .5 moa.
I'm going to play with neck tension a bit, and maybe some seating depths before calling it good. Cheers
 
Had a bit of a surprise using a different primer yesterday. Used Federal 205M to see if I could bring ES/SD down from the 450's. 40.8 grains of H4350 with Amax 105's (great hunting bullet) gave me 3065 average for 5 shot groups with an ES of 8 and a SD of 3. Group was @.5 for several groups. Found a problem with the firing pin piercing random primers going back to when the barreled action was purchased, and decided to send it off to Gre Tan for a bushing job. Know that won't be a problem when I get it back. Cheers
 
Here is my recent work up:

AI ASR
6MM Creedmoor
Proof carbon 24 inch pre-fit
41.00 RL16
Virgin Lapua SRP brass
CCI 450
Berger 105 Hybrid
COAL 2.806
98 degrees. 2500 FT.
3108 FPS Avg.
SD 4.2
ES 11
.57 MOA @ 108 yards. I backed up to 535 and got a first round dead center of the plate. Love this gun and this cartridge!
 

Attachments

  • 3E883715-B392-4713-B8B6-4109F7778A43.jpeg
    3E883715-B392-4713-B8B6-4109F7778A43.jpeg
    980.7 KB · Views: 180
  • 67BDA80D-84C2-489B-92D3-78DB432BE20D.jpeg
    67BDA80D-84C2-489B-92D3-78DB432BE20D.jpeg
    416.5 KB · Views: 188
  • 1A8552FB-E30D-4D20-92AB-E41199CC5DE4.jpeg
    1A8552FB-E30D-4D20-92AB-E41199CC5DE4.jpeg
    390.6 KB · Views: 180
  • 4CECE18E-633F-4191-BA35-942337EE40FD.jpeg
    4CECE18E-633F-4191-BA35-942337EE40FD.jpeg
    364.7 KB · Views: 172
Last edited:
Interesting follow up to my last post: I was able to obtain a box of factory loaded Berger brand 6mm Creedmoor which is loaded using the same components I use (Lapua brass and Berger 105 hybrid). Same day I shot 5 of them back to back with with my pet load of 41gn of RL16.

factory Berger seated to an avg coal or 2.745 inches.
my pet load i have moved to be seated at 2.780

factory Berger: 2896 FPS avg SD 7.2 ES 19. I only shot 5 of these.

Pet load of 41.0 RL16, virgin Lapua brass and Berger 105H: I did two shot strings. 10 rounds was avg 3092 FPS SD 7.7 ES 25. Then I did an 18 round string avg 3094 FPS SD 8.8 ES 31

air temps were 65 degrees 2500 ft elevation.30 degrees air temp cost me 14 FPS.

I guess in conclusion I’m surprised the factory Berger is 100FPS slower. I didn’t think 41 grains or RL16 was on the high side. Certainly no pressure signs and recoil is non-existent in the AI ASR. The barrel a carbon proof prefit which now has 218 rounds on it
 
Interesting follow up to my last post: I was able to obtain a box of factory loaded Berger brand 6mm Creedmoor which is loaded using the same components I use (Lapua brass and Berger 105 hybrid). Same day I shot 5 of them back to back with with my pet load of 41gn of RL16.

factory Berger seated to an avg coal or 2.745 inches.
my pet load i have moved to be seated at 2.780

factory Berger: 2896 FPS avg SD 7.2 ES 19. I only shot 5 of these.

Pet load of 41.0 RL16, virgin Lapua brass and Berger 105H: I did two shot strings. 10 rounds was avg 3092 FPS SD 7.7 ES 25. Then I did an 18 round string avg 3094 FPS SD 8.8 ES 31

air temps were 65 degrees 2500 ft elevation.30 degrees air temp cost me 14 FPS.

I guess in conclusion I’m surprised the factory Berger is 100FPS slower. I didn’t think 41 grains or RL16 was on the high side. Certainly no pressure signs and recoil is non-existent in the AI ASR. The barrel a carbon proof prefit which now has 218 rounds on it
I’m shooting 38.9 grains with a 112 match burner in ADG brass. I find rl-16 is fast. I get 2995 fps. I had it running real hot at 39.9 grains. It was pushing 3080 fps. But I also run into pressure sooner with ADG
 
Interesting follow up to my last post: I was able to obtain a box of factory loaded Berger brand 6mm Creedmoor which is loaded using the same components I use (Lapua brass and Berger 105 hybrid). Same day I shot 5 of them back to back with with my pet load of 41gn of RL16.

factory Berger seated to an avg coal or 2.745 inches.
my pet load i have moved to be seated at 2.780

factory Berger: 2896 FPS avg SD 7.2 ES 19. I only shot 5 of these.

Pet load of 41.0 RL16, virgin Lapua brass and Berger 105H: I did two shot strings. 10 rounds was avg 3092 FPS SD 7.7 ES 25. Then I did an 18 round string avg 3094 FPS SD 8.8 ES 31

air temps were 65 degrees 2500 ft elevation.30 degrees air temp cost me 14 FPS.

I guess in conclusion I’m surprised the factory Berger is 100FPS slower. I didn’t think 41 grains or RL16 was on the high side. Certainly no pressure signs and recoil is non-existent in the AI ASR. The barrel a carbon proof prefit which now has 218 rounds on it

I shot the Berger Ammo with the 105 hybrid out of a 20” tikka and got 2,900 also.
 
  • Like
Reactions: rcorby2
Anyone running Varget with the Sierra 110 SMK, Barnes 112 Gr or 115 DTAC’s?
I think Varget would hit pressure early with those heavies. If you have a low internal capacity case you might be okay?
 
I think Varget would hit pressure early with those heavies. If you have a low internal capacity case you might be okay?

I was thinking the same. There’s data for the 110 SMK’s with Varget, but nothing for the Barnes 112.
 

Attachments

  • 6C47294C-06A1-4B58-87C0-63118D00A190.png
    6C47294C-06A1-4B58-87C0-63118D00A190.png
    799.1 KB · Views: 162
If it’s all you got you try it. You’re giving up 100-150 FPS but accuracy trumps speed every time.
 
Last edited:
  • Like
Reactions: USMC#1
Anyone have any hard data (not bubba stories) about slowing down the speed of 6CM to preserve and extend accurate barrel life?
 
Chamber & twist question.
Looking to get a new 6 CM bbl.My choice of chambers are the 6 CM. and the "match" 6 CM chamber. With a Max range of 600 Yds. I don't see the need to shoot anything heavier than the 108 ELD's. Also my choices are either a 26" with a 1-8 T or a24" with a 1-7.5 T
I don't thing there would be much difference between the 24 & 26 " bbl'a as far as MV goes. And the 1-8 T would probably do better with the Hornady and Nosler 105's. This will be for "steel banging" only
 
Thanks. I think I started too low with the coated 115's
Remember, coated bullets take more powder to get the same speed. That friction reducing coated bullet won’t build as much pressure as a naked bullet.
 
Remember, coated bullets take more powder to get the same speed. That friction reducing coated bullet won’t build as much pressure as a naked bullet.

I knew that would be the case, just wasn't sure how much extra I would need to get where I should be
 
Chamber & twist question.
Looking to get a new 6 CM bbl.My choice of chambers are the 6 CM. and the "match" 6 CM chamber. With a Max range of 600 Yds. I don't see the need to shoot anything heavier than the 108 ELD's. Also my choices are either a 26" with a 1-8 T or a24" with a 1-7.5 T
I don't thing there would be much difference between the 24 & 26 " bbl'a as far as MV goes. And the 1-8 T would probably do better with the Hornady and Nosler 105's. This will be for "steel banging" only

The 6 Creed match chambers have less free bore than the standard chamber.

Hand loads or factory ammunition?

Barrel twist, unless you’re looking to run the heavies then the 1:7 or 1:7.5 is ideal if not 1:8 is fine.

Barrel length, You’ll loose anywhere from 25 to 70 FPS between the two, however, it could be more, and it could be less.

Just to bang steel? Take a pick, you’ll be happy with either.
 
i'm just getting into 6CM...have some 115 dtacs on order and will be spitting them through a Krieger 1/7.5. would anyone like to share data on powder...RL16 or H4831SC...I have both CCI BR4 and 450's and will be using lapua brass. TIA