• Get 30% off the first 3 months with code HIDE30

    Offer valid until 9/23! If you have an annual subscription on Sniper's Hide, subscribe below and you'll be refunded the difference.

    Subscribe

  • Having trouble using the site?

    Contact support

Group Buys Aftermarket AI "Obsession" Chassis - Group Buy

#451
@samb300, 2 questoins:

1. what are the odds of another run in the next 6 months?
2. What pants are your rocking with built in kneepads? I need some of those for my beat up knees during matches and maybe to get promoted at work, lol
 
#452
So I just noticed last night that I never swapped the male catch for the stock on the left side of my AT and when I went to install it found that the corresponding screw head did not clear the comp trigger. I had to file off a little bit of it. Anyone else have that issue?
 
#453
verdugo60 said:
@samb300, 2 questoins:

1. what are the odds of another run in the next 6 months?
2. What pants are your rocking with built in kneepads? I need some of those for my beat up knees during matches and maybe to get promoted at work, lol
Click to expand...
I'm working with a shop to potentially make some for the European market, with the possibility of importing some of them direct into the US, rather than having another large batch made here. That seems to be moving fast, so stand by for more information. If I get another batch made here instead it would for sure be 4-6 months to complete once I issue a PO.

I use inexpensive 5.11 Tactical pants that have an internal knee pad pocket for neoprene pads. They work well and are cheap, but don't breathe well during hot/humid months, and don't repel water. I bought a pair of much nicer UF Pro pants, but with the exact same waist and inseam as the 5.11 they fit me like skinny jeans in the waist and thigh area haha.
 
  • Like
Reactions: impactaddict, *Tavman* and verdugo60
#454
EmanP said:
So I just noticed last night that I never swapped the male catch for the stock on the left side of my AT and when I went to install it found that the corresponding screw head did not clear the comp trigger. I had to file off a little bit of it. Anyone else have that issue?
Click to expand...
The kit comes with the correct replacement screw for the AT male stock catch.
 
  • Like
Reactions: EmanP
#456
samb300 said:
I'm working with a shop to potentially make some for the European market, with the possibility of importing some of them direct into the US, rather than having another large batch made here. That seems to be moving fast, so stand by for more information. If I get another batch made here instead it would for sure be 4-6 months to complete once I issue a PO.

I use inexpensive 5.11 Tactical pants that have an internal knee pad pocket for neoprene pads. They work well and are cheap, but don't breathe well during hot/humid months, and don't repel water. I bought a pair of much nicer UF Pro pants, but with the exact same waist and inseam as the 5.11 they fit me like skinny jeans in the waist and thigh area haha.
Click to expand...

Thanks for the pants info, I like how 511's fit but don't need tactical skinny jeans, lol

So the shop is in Europe? Feel free to PM if you're not ready to put info out yet, thanks dude, you're the man! Gotta get one of your thumbrests for my AI AT LE model!
 
#457
So anyone got a lead on some green grip panels?
1602554428606.png
 
#464
Uhh so, I've only messed around with my newly cured gun around the house, but is anyone else experiencing this thing being like a step change more stable over the AI AT? This is my first season shooting PRS but having the balance not on the magwell is amazing
 
  • Like
Reactions: samb300
#465
Takashi said:
Uhh so, I've only messed around with my newly cured gun around the house, but is anyone else experiencing this thing being like a step change more stable over the AI AT? This is my first season shooting PRS but having the balance not on the magwell is amazing
Click to expand...
Yup! Tune the balance point to be 3-4" in front of the mag well, and it will ride a heavy bag like nobody's business. Combine that with the forend being an inch closer to the barrel than the AT, and it makes it significantly more stable.
 
#469
dbransco said:
It’s been too long, but finally got home and got the AT put together. Still waiting for epoxy to cure, but should sight in/get some groups tomorrow. Thanks Sam! Great design and great package you put together!! Can’t wait to get in some matches.
View attachment 7447556
View attachment 7447561
View attachment 7447558
Click to expand...
Looks so clean, I love it!

How do you like the RRS scope mount? They look so sleek, I’m really thinking about one for my next optic instead of a Spuhr.
 
#473
reubenski said:
My AO chassis has really grown on me. I haven't been able to shoot it much bc I was Antelope hunting, then traveling for work for a couple of weeks, then caught COVID while traveling. But hopefully I'm better next week and can shoot it more. At least I've had time to process and load about 1500rds of 308W brass.
Click to expand...
Yeah, I was afraid of that... 🤨
 
#474
reubenski said:
My AO chassis has really grown on me. I haven't been able to shoot it much bc I was Antelope hunting, then traveling for work for a couple of weeks, then caught COVID while traveling. But hopefully I'm better next week and can shoot it more. At least I've had time to process and load about 1500rds of 308W brass.
Click to expand...

Haha, well 1500 should get you through for a while. Good start. Hope you feel better soon!
 
  • Like
Reactions: reubenski
#480
If anyone is on the fence about the chassis, don’t hesitate if Sam re-runs. Pictures are a bit deceiving and the chassis can look out of proportion, but DBransco was gracious enough to let me look at his rifle and believe me when I say that everything looks like a fine sports car.
No doubt that I have to try and get the chassis!
 
  • Like
Reactions: Rory_Fritz, RS14 and samb300
#487
J-Ham said:
So much for being 1 of 40, haha! Seriously though, that's awesome Sam... I'm super happy for you!
Click to expand...
Thanks! Yeah, sorry to decrease the rarity and collectibility of your chassis haha. This one will actually be slightly different, so there will likely still only be 40 of the exact design of the first run. I'm working on getting some to the European market more easily than if I had them made here, and the benefit will be having more made for the US market as well.
 
  • Like
Reactions: RS14, bb505, J-Ham and 1 other person
You must log in or register to reply here.

Similar threads

A
SOLD WTS: AI AXSA modified for competition in Vision Chassis
Replies
1
Views
344
afd77
A
L
Accessories AO vision AI Chassis
Replies
3
Views
615
Landon
L
L
LPM PR-Comp Chassis
Replies
0
Views
136
Lange's Precision Machine
L
reximus
SOLD Accuracy International "AT" in 6mm GT
Replies
20
Views
2K
reximus
reximus
AXMC
Accessories *UNICORN* First run AO chassis kit for AI AT PRICE DROP 8/31
Replies
49
Views
5K
AXMC
AXMC
Top Bottom
Back
Home
Forums
Merch
Alerts