I saw that trigger tech is coming out with a tikka trigger announced at Shot Show. Does anyone have info on it? Single or 2 stage? Pull weight range????

Looking to spend $300-$500 for a matched receiver set for a precision build. Okay with both forged and billet.

I've run tension screws in the past, they're fine, but I'm looking for a bit more solid lockup.

I've looked at centurion and JP for forged. Rainier for billett. Haven't looked at much beyond this.

What are your recommended matched sets? What has solid lockup? Please specify if it was forged or billett.

Hi All - If budget/money was not a constraint, what is the rifle you would build for PRS matches? What action, stock/chassis, barrel length, twist rate, caliber, total weight, trigger etc you would choose?

Also, if possible also please share a bit about your experience shooting PRS matches.

Like new ATN X Sight 4K Pro 5-20. Comes with everything as it did new PLUS the external battery pack and cheek piece. $500 shipped or might trade on a descent FFP scope, bipod, or???

I am in need of a digital powder dispenser since my 2nd Intellidroper has just died. Been using them for several years, they just aren't built for longevity. Also, the second one would throw a heavy charge about every 8-10 charges. Without spending " supertrickler or autotrickler" money, who do you like. I have looked at the RCBS match master but that's pretty spendy itself. I guess this leaves Hornady, Lyman or RCBS chargemaster (or whatever the cheaper one is called now). What do you like?

This is a Kreiger 6GT done by Joe Walls
26” MTU profile
5/8x24 threaded
1:7:5 twist
1000k rounds on it. Plenty of life left

I have not shot this barrel. I purchased last week for more than I am asking. Only selling because I wound up with two matching barreled actions.

$300 shipped via PayPal F&F, Venmo, or Zelle

Rem 700 trued LONG action from northland shooter supply. Bolt fluted and threaded at LRI, mcgowen 28" 1:8 barrel with area 419 brake, xlr evolution chassis, tt special curved shoe trigger, don't have a magazine as it came with a standard case magazine(will come with) has right at 300 rounds on it. Will come with 49 or 50 pcs of adg brass from this rifle. NF 40MOA rail
$1500 shipped

Looking for a 16.5” AI AT/AX small tenon (27mm) in .308 or 6.5 creed.

Needs to be 5/8-24 muzzle thread

Used is fine if you know the round count.

I have 250 pieces of alpha 6br brass sized down to 22br. It has been fired 4 times. 88eldm’s at 2950fps. It has not been ran over pressured or even near. I also have a Forster 22br sizing die that has been honed to .2450” to match the alpha brass necks. Would like to sell them together. Brass is $0.50 each, so $125 and the die is $50.00 for a total of $175. I’ll pay shipping. PayPal F&F preferred

For sale are two ats tuners. Knew they are 200 bucks plus shipping and taxes. 150 a piece shipped and insured

Brand new ReachIR LRF rangefinding monocular in stock ready to ship!

DM for unbeatable prices.

The FULL ReachIR Product Line:

AGM ReachIR LRF 25-384

AGM ReachIR LRF 35-640

AGM ReachIR LRF 50-640

Login to view embedded media
Later, Zac

So not only does it target them and organizes violence against dealers and owners... it has a "Molotov Cocktail" icon to encourage arson and attacks.

Tesla owners were the darlings of the left until just a few weeks ago. Saving the planet and all that...

But someone took away their Twitter... and now is cutting their funding. So the answer? No... don't come up with better ideas or better political messages... nope, turn into domestic terrorists.

Bondi and Patel have said Tesla attackers will be treated as domestic terrorists. So let's see these idiot start to go to jail and if they cause injuries or deaths, they can ride the needle.

They are unhinged and unleashed! And life means nothing to them because they now think Tesla Owners are committing genocide...

Heads on a swivel, folks. They won't stop with Tesla owners! And when their molotov bombings don't work out.... they'll go after something new. With just as much violence. Churches? Elks clubs? Schools (as usual). Your restaurants that serve that meat (which is murder, after all). These folks are unhinged. And are being turned loose on America.

Sirhr

Osprey .45 supressor New in box. ON a form four in Ohio so.......... Ohio residents only

$500.

Dayton, OHIO

I once shot a half dozen rounds from a buddy’s bolt gun with a popular can from 10 years ago. I think it was a Gen1 RPR. I was blown away with the amount of suppression and have been pining for one ever since. Beyond that I have zero experience firing suppressed. A few months ago, I put out an inquiry for suggestions, and thank you for the responses :

https://www.snipershide.com/shootin...k-pressure-30cal-can-so-many-choices.7244768/

I went with the new HUXWRX 36ti in the hopes of getting it my on M76 and M49, optimistic that the newer flow-through design would behave well on them as well as other semi milsurps. This was an interesting experience. I had three hosts to revolve through today. I shot five round groups before and after and observed peculiar (to me), inconsistent results between rifles:


RPR in .308

• This is a sub MOA gun when I do my part with the ammo it likes (168gr FGM)
• When suppressed it’s PoI shifted 3.5” down x 1.5” left
• Report was a fairly sharp, loud snap but does not ring the ears

RAR in 7.62x39

• This is a 1.25” gun with best performing ammo, so far being Rommy surplus :-/
• PoI shift was 2.5” straight up with no drift in windage
• Report was a pleasant sharp snap

LAR8 Elite Operator (basically Rock River’s AR10 pattern from 10 years ago)

• I fired a string with it’s Vortex flash hider and got about 2+” group using XM80 Lake City, 150gr “ball”
• I then fired a string, bare-muzzle (w/o the Smith Ent, “Vortex”) and got abou 1.5” group (THAT was a surprise)
• Next, I fired five rounds with the 36ti and got the same 1.5” group with literally NO PoI shift (huh?)
• Report was quite a loud crack+POW that would almost ring my ear.
• Perhaps not hearing damaging loud BUT not nearly the amount of suppression as the .308 bolt gun. Is this to be expected?

All in all, I was pleased with the performance on the two bolt guns. From what I’ve read I believe a traditional baffled can would be even quieter on bolt guns. Yes?


Takeaway/questions:

• Is it typical for such a PoI shift with vs. w/o the can.
  • Strange that the .308 RPR would shift down and to the left whereas the x39 RAR would shift straight up.
• While I need to do further testing it’s also interesting/revealing that after all these years the Vortex flash hider unbeknownst to me, may have been hindering accuracy on the LAR8
  • Why no PoI shift on the AR10 ?
• AND why I this semi-auto vs. the bolt guns so much louder. Typical? Moving parts and places for gasses/sound to escape?

Thank you for taking to time to review this and offer any contributive insights.

Moving out of long distance shooting and selling a few items. This Kowa TSN-66A w/Zoom Eyepiece is amazing and has been out maybe 10 times. It's in excellent condition with no marks, nicks, or dings that I can see. Comes with the factory box, arca rail installed, transportation cover for the unit, and factory manual. First, I’ll take it gets it at $2150 shipped to your door CONUS.

Tried to remove one of the spacers in the butt pad - screws wouldn’t bottom out subsequently.

Are there shorter screws available for this?

Does anyone make a cover for an ARCA rail to make it more comfortable to grip? If you have a rail on the bottom of the rifle it can be annoying to hold. I’m thinking something like the rubberized covers you can put on Pic rails that can be pulled off quickly if you want to use the rail but otherwise can be used for a more comfortable experience.

Thanks

Looking to buy a used APA 1/2x28 .224/6mm muzzle brake for my AR match rifle.

Throwing around the idea of selling this rig. Absolutely love it though so it’s for sale but not on sale. Just testing the waters for right now.

My understanding is this rifle was built by Dallas for Jake (owner) at unknown munitions and he then sold it for whatever reason to another guy (who was a lefty but bought this?) and I bought it from that guy. It’s not perfect, it has some scratches and the stock has some sharpie(?) on it I’m not entirely sure why, it didn’t bother me and I liked the naked carbon but if the stock was cerakoted it’d hide all the impurities. I fielded it in Oregon and Wyoming last year and shot only 30ish rounds through it since I bought it because I got some of the loads Jake developed for it but I can’t duplicate it because I don’t have some of the components and refuse to pay gunbroker prices.

According to Jake’s handloads it shoots 225eldm’s at 2875fps with 91gr of n570, Petersen brass, fed 215m’s, seated at 3.590 oal

300 Norma specs
- Defiance Anti-X long action lapua .750 bolt
- 18” carbon 6 magnum contour, extended 1.25 tenon
- AG composites alpine hunter, 2 flush cups on left side, 1 sling swivel on bottom rear of stock
- triggertech special single stage
- Hawkins m5 dbm bottom metal
- accurate aics cip mag 5rd
- salmon river solutions ti pro 5 port self timing brake
- unknown munitions short hunter rail (arca and picatinny)

$3900 firm

*pm any questions please*
**optic not included**
***dies (hornady match bushing die set, sac bushing, and brass (Petersen 1x and unfired, 100 pieces total) available with rifle for additional money if desired***

Looking for a NF RAP-i A688 in like new condition. Must be willing to take a phone call / video chat to make sure you actual have it and don't just want me for my body.

Surefire Wrist Light 2211

300 lumens of hands free light

Li-Ion battery

3 brightness levels

300, 60, 15 lumens

300- 1 hour
60- 4 hours
15- 13 hours

Used little, good condition

$140 shipped

I recently bought a Seekins SP10 in 6mm Creedmoor that I plan to use in PRS gas gun and other competitions. Naturally I'd like to use as aerodynamic of bullet as possible and I have an assortment to try and see what the gun likes. The good news is that so far it shoots everything pretty well. The bad is that it won't feed Berger 109s. The ogive is long enough that the meplat hits below the bottom of the chamber before the feed ramps kick the bullet up enough for it to run into the chamber like it normally would. The gun feeds 108 ELDMs with no issue but the ogive profile on those is quite different from the 109s. I presume I will have the same feeding issue with 110 SMKs and most of the 115 class bullets as well.

I have been using PMAGs. Would a different mag make a difference or is this a case of AR10s aren't designed to shoot super sleek 6mm bullets? Is there anything else that I can try within reason? The gun shoots the 108s just fine and they will work for what I need so I'm not up a creek but I would like to at least have the option to use some of these other bullets.

Stock is new, unused, has not been installed.

$200 now $190 shipped.