Remington 700 Triggertech Special. Used for a few hundred rounds. Comes with everything as from the factory (Allen key, patch, manual, etc).


$125 shipped. PayPal FF. No trades.

Does anyone know the torque spec on the A-0119 Bubble level? I can't find it on the website and it didn't come with any instructions.

For some reason, I can’t wrap my head around this question if the shooters at 1000 yards using the first vocal plane mil reticle and the spotter is at 500 yards with a fixed mil reticle spotter.Can the spotter still call mil change? For some reason I feel like he should, but the difference in distance makes me question that.

Leofoto SA-324C, MA40 Ballhead, LSC-50 Arca Clamp, Coletac Tripod legs (Gen 1 with the straps not the cord lock) and rock caddy.

This has been on a few hunts and used at the range/in my garage. Has handling marks and some wear marks. Works 100%. Decided I want to go with something a bit lighter and a fluid head. $360 shipped for everything.

Only trade would be for a peak 44 Teton tripod.

Surgeon PSR rifle wth 20 inch barrel. Done by Wade Stutteville. This is an unfired beautiful rifle that doesnt need to sit any longer. Surgeon 1581 XL action, McMillan A5 stock, Surgeon XL DBM, 2 CIP length mags, triggertech diamond single stage trigger. Barrel has PSR brake with thread protector.

$4000 shipped. Bipod, suppressor, and scope not included. No trades, besides SRSA2 barrels/accessories or HK stuff.

Looking for a carbon barrel in 6.5CM for my Zeus QC before I order new. Preferably low round count and length in 20”-22” but open to what comes across my paths.

Thanks.

@iosononik gave a feeble attempt to get me. Good initiative, bad judgement.

So i decided to go down the route of 6arc and have the kgm r556 heavy duty use suppressor, has any one used 5.56 dedicated suppressors on their 6 arcs and if so, did you see deviations in it? Also, if it’s applicable should I just get a 30 cal?

Selling a used Nightforce NXS 5.5-22x50. This one is second focal plane and has the NP-R2 benchrest reticle. Dial is in .25 MOA graduations. Scope is in overall pretty good condition with only a few of small blemishes. Glass looks clear, however if you look on the right hand-side (2 o'clock) there is a small piece of debris. Its only visible at low magnification. The glass looks perfect to me, so I dont know if its something within the scope or if it just needs a deep cleaning. Comes with an AI scope picatinny mount (not sure of the cant or height dimensions as it came on a rifle I purchased). DM me with any questions.

Asking $SOLD shipped. Can accept payment via Zelle.

Open to Trades + cash deals. Trades include KAC stuff, AI stuff.

How do the 44mm compare to the 55mm ball heads or is there a better head to pick for prs/nrl? Thanks

Looking for KRG Bravo Enclosed forend for TikkaT3 short action.

Please let me know what you have.

Looking to sell this new CA762SSAL/RE, mounted but never fired. Brand new minus shims. Getting harder to find, asking $500 shipped. Thanks!

Athlon Midas Tac 5-25x56 (#213082) rifle scope. 34mm tube, FFP, with APRS6 reticle.

Asking $450 shipped.

CDI 501 MRMH 1/4” drive Inch Pound Torque Wrench (*Snap-On) 10-50 inch pounds

Like new condition, only used for fasteners on one rifle assembly action, scope, etc

Comes in plastic case

Great tool

$115 shipped

I have up for grabs 2 trijicon 5x50x56 tenmile scopes for sale one moa SOLD and one mil includes scope sunshade and scope caps, rings and level would be extra $1500 each shipped conus These are cross posted so time stamp wins

Anyone make one like this. Ideally able to be peeled off like the magpuls. Maybe we should petition magpul

Good condition other than a scratch on the turn knob I seen the picture. They were great $850 shipped

Vortex Radian ball head
Brand new - came with the tripod, I replaced it with a tac table.

$175 +
PPFF, Venmo Gift, Zelle

I have a Nightforce Ultramount (20moa Cant) on my AR10 that I am leveling my ATACR. nightforce calls for 100 in/lb on the mount bolts. With roughly 40 in/lb the mount and the upper are perfectly parallel with each other. But I noticed that once I torque to the full 100 in/lb nightforce calls out, the mount is no longer level to the upper. almost as if the mount torqued itself few degrees in one direction.

is this a common issue with scope mounts? Are some mounts more prone to this than others? Any suggestions on what can be done?

Unless I can figure out a solution, I guess im going to have to choice but to level the scope to the mount and not the rifle.

I have a question for those of you who use a turret magnifier. I see them mounted at 12 oclock in a lot of pictures. If you mounted one at 10 or 10:30 for a right handed shooter, would it work well to see the turret with your left eye without breaking position/lifting your head? I'm thinking about getting one, but I'm concerned the magnifier won't work since it would be at an angle in relation to the turret.

I have very limited central vision in my left eye from an injury, so right now I have to pick my head up off the comb to see the turret with my right eye. I'm hoping a magnifier+idts tape with colored markings will make it so I can see well enough with my left eye to adjust the turret without lifting my head up.

Hey gang. Looking for a new precision barrel for my original OBR. Found the threads on here with some great recommendations for shops and vendors, thanks for that.

Problem I’m having is best I can tell the OBR doesn’t use a DPMS style barrel extension, it’s proprietary to LaRue. Can I reuse the extension off the LaRue barrel? Never got that deep in the weeds before on one of these. Thanks in advance everyone. Really appreciate the help.

Leupold Mark 5 CF-440 Tripod Great shape

$400 Shipped

No need to wait, we have a Foundation Samson centurion grip stock inlet for Impact and Vudoo.
Message me here or order right away on the link.

Selling my Labradar with Bluetooth. Includes a trigger, arca plate, power supply cable and picatinny section with sight built in.

Asking Spf .

Like new Magpul PRS lite stock. I had it mounted, but ended up going a different route. $80