Accuracy International Picture Thread

[carbonbased]

It wasn't a prefit. Custom job done by JR Firearms in the UK.


I've got an injured hand at the moment so controlling the rear bag has quite uncomfortable.. was still sub MOA at 900yds but nothing to shout about.

At 100yds it was .2 -.3 MOA groups all day... prior to my injury...

Don't wear wedding rings folks.. that's all I'll say as the rest is quite graphic

Ah, degloving? I have not the pleasure of experiencing that.

I wish you a speedy recovery.

 

[JayjayUK]

Ah, degloving? I have not the pleasure of experiencing that.

I wish you a speedy recovery.

Yes indeed. Fortunately they saved my finger on the night and just needed everything stitching back together.

3 weeks later the wound has healed but still swollen like a balloon.. so trying to get back out shooting but after about 5 minutes of adjusting a bag with just my forefinger and thumb it was getting a bit sore

 

[Rhed]

Comparing the s&b to tt (5x25), I'd take the TT for sure. But with the s&b 6x36 I was using yesterday on the TRG, I'd probably pick that over the TT 5x25. My old eyes need some higher magnification

Thanks..

 

[xxflyingturtlexx]

Nice paint! But that grip is giving off serious “banana in the tailpipe” vibes

I hate mdt and am open to suggestions on 90 degree grips

 

[Charger442]

I hate mdt and am open to suggestions on 90 degree grips

does it need to be 90 degrees? because this grip on an AR is the GOAT of grips and should be excellent on that chassis also.

ERGO FLAT TOP TACTICAL DELUXE GRIP – SUREGRIP® - ERGO Grips

The palm filling Tactical Deluxe Grip with aggressive texture. The top has been made flat so it will fit onto chassis system stocks that take AR-15 type grips. Although this grip will fit on an AR-15 type rifle the back of the grip does not lay flush with the back of the receiver (check out the...

www.ergogrips.net

id run it long before you grip that actually looks acute.

 

[Part Timer]

I hate mdt and am open to suggestions on 90 degree grips

Here’s an option for you. MK Machining

 

[PSS 308]

Wish I could find cheek peace screws from Accuracy international very difficult to locate

 

[PSS 308]

 

[sidetoss20]

Wish I could find cheek peace screws from Accuracy international very difficult to locate

If you don’t need the AI-specific ones, these worked for my legacy R700 AICS (and I suspect would work on the other thumbhole variants of factory AI guns but not sure): https://a.co/d/9xuRrBl

 

[PSS 308]

Looking for some Accuracy, international cheek piece screws not much luck

 

[PSS 308]

If you don’t need the AI-specific ones, these worked for my legacy R700 AICS (and I suspect would work on the other thumbhole variants of factory AI guns but not sure): https://a.co/d/9xuRrBl

I kind of wanted to get the AI ones

 

[carbonbased]

I kind of wanted to get the AI ones

I sympathize. If you give up, these are nice. Not as cool, but nice:

Upgrade in cheek piece for Accuracy International Stocks

I know I saw somewhere, a pad to put on the cheek piece to make it more "tacky" than the stock one. Anyone know what I am thinking of? Thanks in advance.

www.snipershide.com

If you want the 25mm long non-AI ones I have and you’re in North America, dm me your address and I’ll send you them for free. They’re a little too long for my tastes (see link) but they’ll tide you over.

 

[CANAVAR]

Looking for some Accuracy, international cheek piece screws not much luck

Accuracy International - Cheekpiece Thumbscrew (Single) - 20333

Genuine Accuracy International Cheekpiece Thumbscrews. Price shown is per thumbscrew not a pair. * Please note these no longer include AI logo. ** Not suitable for new AT-X.

www.sportingservices.co.uk

 

[CANAVAR]

Accuracy International - Cheekpiece Thumbscrew (Single) - 20333

Genuine Accuracy International Cheekpiece Thumbscrews. Price shown is per thumbscrew not a pair. * Please note these no longer include AI logo. ** Not suitable for new AT-X.

www.sportingservices.co.uk

These are available too. I've ordered from them several times and no issues.

Sporting Services - Cheekpiece Thumbscrews (Pair)

Accuracy International compatible Cheekpiece Thumbscrews. Price shown is for a pair. * Not suitable for AT-X.

www.sportingservices.co.uk

 

[JayjayUK]

I hate mdt and am open to suggestions on 90 degree grips

The new Vision Grip is supposedly very good from speaking to a couple of the Vision Pro team.

 

[ta1on]

Guys where can I find weights that fits the AXSR chassis ?

 

[SpeedDrop]

Guys where can I find weights that fits the AXSR chassis ?

Win-Tac weights that are specific for AXSR Keyslot are available at EO & Mile High

 

[ta1on]

Win-Tac weights that are specific for AXSR Keyslot are available at EO & Mile High

Thanks

 

[hafejd30]

Has anyone with an ATX played with the action screw torque?

 

[xxflyingturtlexx]

Has anyone with an ATX played with the action screw torque?

I plan on taking mine apart if i can find directions because the rear left screw was loosish and i never touched it before. I saw my proof barrel a tiny amount tilted to the left torqued to spec and went over all the bolts, that is when i found out one of the action screws was not torqued. It needs deep cleaning so i plan on taking it apart.

 

[xxflyingturtlexx]

The new Vision Grip is supposedly very good from speaking to a couple of the Vision Pro team.

You know i forgot about that

 

[Huskydriver]

View attachment 8442025

That Remington is about as soy as that bed spread.... #notanAI

 

[diggler1833]

They Remington is about as soy as that bed spread.... #notanAI

Beat me to it. Was about to post a Caitlin Jenner photo...

 

[diggler1833]

Has anyone with an ATX played with the action screw torque?

I think they do a pretty good job of adjusting themselves when you least want them to....

*has not happened to me*

**yet**

 

[hic28]

Guys where can I find weights that fits the AXSR chassis ?

Sawtooth/dependabuilt also makes some.

Www.sawtoothrifles.com

 

[xxflyingturtlexx]

I was dm’ing Husky but here it is apart somewhat:

Remove barrel (not mandatory, makes it easier if you have a long handguard/nv bridge)
Remove rear chassis bolt.
Remove front chassis bolt
Remove the bolt behind the mag release
Remove the (whatever you call the hinge/sling thingy)

Rail/chassis comes off

Remove 2 trigger screws
Then remove the 4 action screws the action comes off

 

[hafejd30]

I was dm’ing Husky but here it is apart somewhat:

View attachment 8442450

Remove barrel (not mandatory, makes it easier if you have a long handguard/nv bridge)
Remove rear chassis bolt.
Remove front chassis bolt
Remove the bolt behind the mag release
Remove the (whatever you call the hinge/sling thingy)

Rail/chassis comes off

Remove 2 trigger screws
Then remove the 4 action screws the action comes off

I just took mine apart and torqued it. The rear screws almost felt like they were glued in. Damn near gave up I was afraid to strip them. Torqued the action screws to 35 inch lbs per the manual

The screw behind the mag latch is just for the mag latch. Didn’t have to be removed to remove the action.

Also the sling stud/catch for the folder thing…ya you can remove or install that anytime. Doesn’t connect anything internal. Just that catch itself. It’s really easy to strip the head on….ask how I know In my defense it definitely was not in there at 8 in lbs

 

[xxflyingturtlexx]

I just took mine apart and torqued it. The rear screws almost felt like they were glued in. Damn near gave up I was afraid to strip them. Torqued the action screws to 35 inch lbs per the manual

The screw behind the mag latch is just for the mag latch. Didn’t have to be removed to remove the action.

Also the sling stud/catch for the folder thing…ya you can remove or install that anytime. Doesn’t connect anything internal. Just that catch itself. It’s really easy to strip the head on….ask how I know
View attachment 8442501View attachment 8442497

The rear ones were really tight, and made good noise breaking loose. Front ones were hand tight.

I completely reversed that hinge thingy because it gets in the way of my hand and i don't rest my thumb on it. It is a mixture of parts from non hinge and hinge screws. Left side is the sling mount, right is flat bolt head.

 

[hafejd30]

The rear ones were really tight, and made good noise breaking loose. Front ones were hand tight.

Same thing on mine. I torqued them all even to 35 in lbs. Maybe it’ll shoot like crap now idk. But at least if I need to strip down for any reason I know what I’ll return the torque to

 

[xxflyingturtlexx]

You should be alright; now you know all buttoned up per spec-ish

 

[Tim Brush]

Running the 308 AT at the last PRS UK match, this seems to be my ‘go to’ combination currently

 

[JohnDeereGuy1996]

I was dm’ing Husky but here it is apart somewhat:

View attachment 8442450

Remove barrel (not mandatory, makes it easier if you have a long handguard/nv bridge)
Remove rear chassis bolt.
Remove front chassis bolt
Remove the bolt behind the mag release
Remove the (whatever you call the hinge/sling thingy)

Rail/chassis comes off

Remove 2 trigger screws
Then remove the 4 action screws the action comes off

How did you do that paint pattern? I really dig that.

 

[ThatHKMarksman]

First time painting a rifle. Pretty happy with it. I'll need more practice in the future. Rifle is being prepped for an upcoming course.

 

[xxflyingturtlexx]

 

[BurtG]

#myAIhasmokillsthanyours

 

[xxflyingturtlexx]

View attachment 8444798#myAIhasmokillsthanyours

 

[hafejd30]

 

[xxflyingturtlexx]

View attachment 8445105

Jealous

 

[BurtG]

Don’t worry about the deer !


Those weeds ! Those weeds ! They gonna take the whole crop.

 

[hafejd30]

Don’t worry about the deer !


Those weeds ! Those weeds ! They gonna take the whole crop.

View attachment 8445129

I have nothing to do with the weeds or the corn haha

I’m just a trigger puller

I figured a deersniper would understand

 

[carbonbased]

I have nothing to do with the weeds or the corn haha

I’m just a trigger puller

I figured a deersniper would understand

Captain, a new message is coming through the comms!

JEDI U MUST SHOOT THE WEEDS

 

[PrecisionRifleGuy]

This past weekend was our monthly club match at Precision Rifle Queensland in sunny Australia. As always I was shooting my AT-X. This month had the 6 Creedmoor barrel spun on. Unfortunately, the wheels fell off for me in the last two stages and I ended up with 6th overall. When I got home and inspected the rifle, I realised the action was loose in the chassis. That would explain why the last two stages I couldn't hit much. It might be time to bond the action like my old AX.

 

[jff_stvns]

This past weekend was our monthly club match at Precision Rifle Queensland in sunny Australia. As always I was shooting my AT-X. This month had the 6 Creedmoor barrel spun on. Unfortunately, the wheels fell off for me in the last two stages and I ended up with 6th overall. When I got home and inspected the rifle, I realised the action was loose in the chassis. That would explain why the last two stages I couldn't hit much. It might be time to bond the action like my old AX.

View attachment 8445359

Did you ever double check the torque when you first got the rifle ? Just curious.

 

[PrecisionRifleGuy]

Did you ever double check the torque when you first got the rifle ? Just curious.

Yeah. I pulled it all down and torqued it all. The AI dealer here in Australia cerekoted it for me too.

 

[hafejd30]

Would a touch of blue loctite on the action screws be beneficial?

 

[M8541Reaper]

No judgement, but genuinely curious…

Is it not common practice to torque everything down, pops witness marks on every bolt head, and check em before, during, and after each match/range trip?

 

[hafejd30]

No judgement, but genuinely curious…

Is it not common practice to torque everything down, pops witness marks on every bolt head, and check em before, during, and after each match/range trip?

With the ATX checking torque is much more involved then a standard chassis as you have to take it apart each time

 

[carbonbased]

EPOXY MASTER RACE

 

[Shoots 700's]

EPOXY MASTER RACE

Why I just bought a AXSA

 

[BEJ762]

“Action and action screws loosing up? Hahahahahaha!!!!” said AIAW.