Frank from Bartlein should be giving me a ring today. I think I’m just going with 19”. A member here offered to swap hand guards with me. The only problem for me is that his is black and mine is tan... so I gotta think about that.
Single handedly the best humble brag I've ever seen!
Anyone have one of these SKB cases from EuroOptic? I’ve looked high and low for what this circled compartment is cut for. Looks like a small pelican case or something, but no specs really match up. Euro’s stock image shows a bipod in there, but I don’t know why it’s shaped like a small case then.
Attachments
Haven't seen those at Euro. Like some of the other deployment cases, they contain a cut out for a small box to hold tools and such. That's likely what it was intended for.
Right. It just looks awfully specific to a certain case rather than just a square cut out. Here’s the pic that Euro shows.
It’s an extra spot for certain items in general I think that Bipod was too big to be left on the AI and still close the case and if the case could close it would leave the foam impressions on the top or could be just to have the other accessories that are stored that Bipod seems pretty big
Here's the kit from Remington with the case in a similar spot.
Take a look at @xXlojackXx picture. His bipod fits fine and if the butt stock can fold and fit in the case then the bipod certainly can.
Lol me either that’s why bullet gets the big bucks lolI never thought a case on its side like that. Back to searching with new dimensions
I thought it was the same as the comp trigger just the housing is a tad different to fit the axsr
Enjoy....
Accuracy International AXSR's are HERE!!
The adjustment procedure for the AXSR trigger is the same as for the comp trigger. It just won't go as low in total pull weight. The 308 bolts (and 300 WIN MAG) will be available in Q3. The limited edition ASR kits already have the 308 bolt. -Scott @Scott Seigmund any update on when the bolt...
www.snipershide.com
Accuracy International AXSR's are HERE!!
How about the magazines for short action cartridges....do those come out anytime soon or will it be in 2021?
www.snipershide.com
Enjoy....
Accuracy International AXSR's are HERE!!
The adjustment procedure for the AXSR trigger is the same as for the comp trigger. It just won't go as low in total pull weight. The 308 bolts (and 300 WIN MAG) will be available in Q3. The limited edition ASR kits already have the 308 bolt. -Scott @Scott Seigmund any update on when the bolt...
Accuracy International AXSR's are HERE!!
How about the magazines for short action cartridges....do those come out anytime soon or will it be in 2021?
thanks man. I wish they would have just put that it was adjustable in the owners manual but I gained some other knowledge as well considering I want a m-lok forend and my plan might not give well with MDT weights near the receiver end due to barrel OD and mlok screws touching the barrel.
@JB.IC @Huskydriver
So the triggers on the ASR/ AXSR is AI's vs the other comp trigger made by X-treme Shooting Products.
The housing on the AI trigger is a lot bigger. I tried messing with it a little as I prefer a heavier pull, but it didn't change much, so I kept it as is.
The ASR/ AXSR is held by roll pins. So not as easy to remove like what you see on older gen rifles with the 4mm screws. So maintenance on the trigger is more PITA as the trigger is held by roll pins vs 4mm screws in the older gen rifles. Also, you have to remove the action from the chassis to do so...
I like the reg AI triggers, but its prolly cause I'm used to it... MLOK is still gay... there's no need to buy weights if you just buy a heavier barrel
So the triggers on the ASR/ AXSR is AI's vs the other comp trigger made by X-treme Shooting Products.
The housing on the AI trigger is a lot bigger. I tried messing with it a little as I prefer a heavier pull, but it didn't change much, so I kept it as is.
The ASR/ AXSR is held by roll pins. So not as easy to remove like what you see on older gen rifles with the 4mm screws. So maintenance on the trigger is more PITA as the trigger is held by roll pins vs 4mm screws in the older gen rifles. Also, you have to remove the action from the chassis to do so...
I like the reg AI triggers, but its prolly cause I'm used to it... MLOK is still gay... there's no need to buy weights if you just buy a heavier barrel
I dunno what your missing other than they make both a fixed stock and a folder version of the AT
Guess I should of asked when I purchased it, I just assumed with the break in the stock it folded. First AI, 2012 AW.
You could find someone who did a Accuracy Obsession/AX stock swap if you wanted to make your AW a folder.
Like @tevan0707 said. It really shouldn’t be too big of a deal to make the swap if you want a folder.
either way you got a great rifle
Win tac is the company who chambers barrels for ai usa. If it's a factory ai barrel, it's a bartlein
Edit...And they friggin hammer @Frank Green ... Keep my hammers coming Frank
Unless it’s a AT, then it’s Lothar Walther. Only AX’s come with factory Bartliens
Here's my first AI but the not my last. Not new to precision rifles, constantly learning from the threads on the Hide. Had several custom builds and top end factory rifles. But I needed to scratch that AI itch. Sold several customs for the funds. Don't even miss them after
shooting the AI. Should have done it 20 yrs ago. I bought a AT .308 PB folder from EO last year. Just Awesome!!! Had admired the AW rifle for years. Found some AW skins thanks to another member. This thread is amazing, with fine rifles.
This was my first AI still regret getting rid of it.
It looks more like the Badger IMUNS since the EFR rides inside the stock, while the IMUNS sticks into the front spigot mount area AFAIK
i need to find one of those multi cam balaclava’s for shooting 200 yards. Super snipery
Looking to get a new barrel spun for doing distances beyond my current 6.5 creedmoor and 300 WM barrels (still debating 300 PRC vs 300 Norma -- any opinion on this would be appreciated, I have a full set of bolts). What's everyone going with these days? EO or Mile High? Both of these vendors don't have much stock listed online. Does a phone call change things or do I have to custom order?
