Search results

Search the forum Search Articles
  1. T

    Gunsmithing Model seven

    Re: Model seven <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: dontstrokeme</div><div class="ubbcode-body">Can a Model 7 use M700 ADL trigger guards? If I were to order a Manners inlet topside for a Model 7, forward bottom hole drilled for Model 7, and rear two...
  2. T

    Serious trouble with AR-15 **UPDATE**

    Re: Serious trouble with AR-15 <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Mikee Booshay</div><div class="ubbcode-body">the rifle can ( but normally won't)fire out of battery ie the bolt not fully locked.</div></div> The firing pin won't stick out the bolt...
  3. T

    who make a pistol AR lower.....

    Re: who make a pistol AR lower..... Stripped lowers are transferred as "other" and can be built as a rifle or pistol if it's never been built as a rifle.
  4. T

    Gunsmithing front sight on flattop ar can be seen in my scope

    Re: front sight on flattop ar can be seen in my scope If you focus on the target and not the front sight you won't even notice it. You might want to shoot it a few times before you get to cutting the front sight off.
  5. T

    Gas block installation

    Re: Gas block installation The best way to keep it from moving is to pin it like a front sight.
  6. T

    Noveske AR-10

    Re: Noveske AR-10 Armalite barrels will fit in the DPMS receiver. The threads limit the interchange of barrel nuts and handguards with proprietary barrel nuts but have nothing to do with the barrel extension fitting into the receiver. Headspace and the length of the lugs may be an issue, as...
  7. T

    Armalite barrel w/ DPMS upper?

    Re: Armalite barrel w/ DPMS upper? There is a significant difference in the buffers and springs used. The gas port should be different because of this. I would use the Armalite barrel, BCG, buffer, spring, and buffer tube (if carbine, rifle is the same).
  8. T

    Gunsmithing Threading a barrel without can

    Re: Threading a barrel without can Use a gunsmith that knows something about tolerances and can thread to 2A/3A and gauge it. I want my next can/brake/flash hider to fit, if I want it tighter I'll bring the can and ask for it tight. Not threading to 2A/3A if the customer asks means one of...
  9. T

    Hunting & Fishing Please Watch.Helihunting New Zealand. Help Stop It

    Re: Please Watch.Helihunting New Zealand. Help Sto <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Kurt</div><div class="ubbcode-body">if you have no seasons and hunt year round sounds like you have no idea what game management is. </div></div> That may be...
  10. T

    Gunsmithing Custom AR-10 Lower and m110 magazines

    Re: Custom AR-10 Lower and m110 magazines The AR-10 upper has a shelf to limit the seating depth of the AR-10 mag. The shelf does not allow SR-25 mags to seat even if the lower is for the SR-25 mags.
  11. T

    Gunsmithing Who makes the Rem 6.8 light tactical rifle stock

    Re: Who makes the Rem 6.8 light tactical rifle stock The light varmint and 6.8 tactical had fluted magnum contour barrels I believe, not sporter and had a nice balance.
  12. T

    Gunsmithing Who makes the Rem 6.8 light tactical rifle stock

    Re: Who makes the Rem 6.8 light tactical rifle stock <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Pointblank4445</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: TMK</div><div class="ubbcode-body">I...
  13. T

    KABOOM !

    Re: KABOOM ! High primers or debris on the bolt face are not firing OOB they are slamfires OOB. Just because the hammer drops does not mean firing OOB is possible. Pull your BCG and hold the firing pin forward, then push the bolt to the rear, the firing pin will not protrude from the bolt...
  14. T

    Gunsmithing Who makes the Rem 6.8 light tactical rifle stock

    Re: Who makes the Rem 6.8 light tactical rifle stock I think it was a B&C, never seen an R3 pad on a HS.
  15. T

    AR-10 buffer

    Re: AR-10 buffer The DPMS LR uses a shorter buffer than the AR-15.
  16. T

    KABOOM !

    Re: KABOOM ! <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: ASM1</div><div class="ubbcode-body">one that fired what looks like it was out of battery over 1/4" </div></div> The AR cannot "fire" OOB. Only a slam fire caused by an improperly seated primer or debris...
  17. T

    300 Whisper is here

    Re: 300 Whisper is here Load up some cheap supersonic loads if you want to shoot it while waiting on the silencer. A rifle .30 cal silencer works very well. It's also the way to go if you have a .308 to use it on and the weight is not an issue.
  18. T

    First AR!! Got some questions

    Re: First AR!! Got some questions I'm talking about the taped on cheek pad on the stock. If you get a rail for the top or bottom it will bolt through the holes in the handguard. If you want it on the side you will have to drill a hole for the bolt.
  19. T

    First AR!! Got some questions

    Re: First AR!! Got some questions A bit of rail like this? http://www.gggaz.com/index.php?id=165&parents=38,44 I would reconsider the stock mod, with proper shooting position your cheek should be nowhere near that cheek pad. The carry handle is a notch to the rear of where it should be. If...
  20. T

    AAC BLACKOUT rifle - should we do .260 Rem?

    Re: AAC BLACKOUT rifle - should we do .260 Rem? .260, threaded muzzle, and DBM for me. I say the cheapest stock with an aluminum bedding block, HS or B&C. The high end stock buyers want a stock just how they want it, never going to make them all happy. None of the other options are deal...
Top Bottom
Back
Home
Forums
Merch
Alerts