Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
Watch Out for Scammers!
We've now added a color code for all accounts. Orange accounts are new members, Blue are full members, and Green are Supporters. If you get a message about a sale from an orange account, make sure you pay attention before sending any money!
What are your cleaning methods for the barrel.Maybe check barrel crown for damage.Also if you are using different loads for SR vs LR it can take 10-12 round for barrel to settle.I once had a 2 inch shift in inpact when switching ammo RL-15 vs AA 2520 .
That seem like a lot of growth for one firing.I have not been a fan of Federal Brass for reloading.I like Lapua and Lake City LR Brass . I do not think that that the length of the case is causing you extraction issues .Factory chambers are usually long in the throat to keep pressure down.If the...
I have seen different powders shift point of impact left or right.For example when I was shooting my Ar-15 .The load with AA2520 would shoot 3 minutes to right compared to Reloader -15 Loads with the same bullet 77SMK. Regards Mike
I would sort by Head Stamp and then by weight.But if you are shooting 200-600 yards I do not think you will see a big difference in group size by sorting by weight.Sorting by volume is probably the best method.But that is some times is done by Bench Rest Crowd and Long Range shooters.It is...
I would pull bullet and remove powder.Then remove primer carefully,Most likely you will find the anvil missing from the primer.You could also check some of your primers from that lot check for defects .(Missing anvil ,lack of priming compound or incorrect size on primer cup. ) Regards Mike
I would recommend using 77SMK bullet for a 1-7 twist .For an AR-15 I would use LC Brass .Make sure you bump the shoulders at least .002 .Make sure the Primers are seated all the way. For the AR I would recommend Wolf SRM Primers ,CCI Mil Spec ,CCI 450 Or Federal Primers designed for use in an...
Varget and Rl-15 should be fine to use .I think that the H-380 will be to slow to use .My load with 175 SMK are 43.2 with RL-15 in LC-LR Brass .For Varget I used 44 Grains in a LC-LR Case .This was the load I used for 1000 yards .If you are shooting less that that you may be able to back the...
For the M1-A Platform try to stick to IMR 4895 and IMR 4064 .I would also suggest to stay in the Bullet weight range of 150-175 grains .The M1-A gas System and Operating Rod was designed around a specific pressure curve.If you can not find the IMR powders try to stay close to their burn rates...
I have had good luck with Varget and the 178 A-Max.If I recall correctly I think I jumped them 25 thousands.I was using Lapua Brass and just under 43 grains of Varget.Start lower and work up load for your rifle.If you can not find Varget try some IMR 4064.IMR 4064 shoots great as well.My 4064...
For my WOA Upper is use 24.2 RL-15 with 77Grain SMK and Lake City Case.For a primer I use Wolf Small Rifle Mag.In my rifle it will shoot around 1/2 MOA.23.2 of IMR 8208 works well also. Regards,Mike r
If your bullets were loose or moving easy after they were seated . You did not have enough neck tension.If you are using a bushing die you will need to use a different size bushing to get the proper next tension.If it is a regular die you may have to use a different die or use a different...
The M1-A/M14 is very tough on the Brass during the extraction process.(Brass stretches a lot ).If shot out of a tight chambered NM M1-A you may get one or two more firings .But the general consensus with with most Service rifle shooters is to toss after 3-4 firings.Its not worth the risk...
I think your load may be a little to hot.Here is the loading data for this powder.You may want to pull the bullets and redo your charge weight.Not trying to be a know it all.I just do not want someone to get hurt or damage their rifle. Regards,Mike 168 SIERRA HPBT MK 38.1 2,487 42.3 2,705...