Both F's 3-24x42 and 52
I will be running Varget with 75/80gr Amaxs ,should end up in the 25/26gr range with it .M77
What powder and charge are you running with which bullet?
Those with the 6.5 CM barrel, have you found most factory offerings shot well?
Factory 140 elds shoot ridiculously well in mine , first group was clover from the barrel .Those with the 6.5 CM barrel, have you found most factory offerings shot well?
Looks fun! What is the height of your scope mount and does your scope have a 56mm objective? I want to get my scope down low like that.Finally got my 223 barrel back from my Smith and took it out for the day .
Such an awesome Calibre for the SRS virtually no recoil , can't wait to develop some loads for it .
big thanks to SAC for the parts ,
Had the barrel made locally in Aus .
24" Lothar stainless fluted 1:8 throated long for 80's .
0.89" at the muzzle slightly heavier than the factory profile . Showing heaps of promise already
View attachment 7252657
Looks fun! What is the height of your scope mount and does your scope have a 56mm objective? I want to get my scope down low like that.
I wishThat mag looks very nice - do SAC do those mags for other calibres?
SP-4802It's a spuhr 4802 - 1.44" I believe .
44 moa /13mil
You can kiss running a front cap goodbye though. Kind wish I had 1.5"
Not sure wtf I was thinking it's been 5 years since I bought it and looked at the specs againSP-4802
13 MIL/44,4 MOA
Height: 38 mm/1.5”
Length: 121 mm/4.76”
Weight: 254 g/9.0 oz
I have the same mount for my TT525P and I noticed I have the cheekpiece at the lowest setting and sometimes still press my face against it.
Apparantly it's been good enough to last 5 years ?Not sure wtf I was thinking it's been 5 years since I bought it and looked at the specs again
You’re going to love it.Finally sent Fred a bunch of money this morning! I’ll be playing this game shortly.
That's good news. With the march is that a 52mm objective? How much clearance roughly would you say there is between the forearm and the objective? 3/16" maybe 1/4"Yes, ran the 1.375" 30mm NF unimount for a short while with a March 3-24x. The mount was fine; I thought it might be too low but it wasn't.
Is that the top of a silo?
Gotta get up high to get to 1500 lolIs that the top of a silo?
Have not mounted it up yet. Vudu has a really tight eyebox fwiwdeersniper how does the VUDU stack up compared to a Steiner?
Getting ready to jump into a DT SRS A2 covert-
My main question is, should I start with a factory barrel, or with a setup from someone like SAC or ES Tactical? Any advantages to either?
I plan on beginning with a 6.5 CM, followed by a 223 in the future.
I have one factory barrel, two SAC barrels, two ES Tactical barrels and one from TS Customs.Getting ready to jump into a DT SRS A2 covert-
My main question is, should I start with a factory barrel, or with a setup from someone like SAC or ES Tactical? Any advantages to either?
I plan on beginning with a 6.5 CM, followed by a 223 in the future.
Buddy's running a 7 saum, feeds great, and it's a hammerIs anyone running a 6.5 SAUM in an SRS? How does it shoot/feed?
I too am interested in feedback on proof barrels in the srs'sAnyone had luck with Proof Research? Those carbon fiber barrels have me intrigued.
I have two. One is a 300 prc done by SAC. The other is a 6.5 creed by ES tactical.I too am interested in feedback on proof barrels in the srs's
Mine is a tack driver! Gerring 3310 with 130 gr.Is anyone running a 6.5 SAUM in an SRS? How does it shoot/feed?
Buddy's running a 7 saum, feeds great, and it's a hammer
Mine is a tack driver! Gerring 3310 with 130 gr.
I bent the lips on a mag and it runs fine