Transitioning my "competition" gun to a hunting stock so I actually use the rifle.

I never ended up shooting competition and the gun was purely for load development on the bench.
That said, it does have some scuffing where the magazine inlet is on both front a rear inside magwell, nothing crazy, otherwise flawless condition

Comes with:
- MDT exterior weights (6)
- MDT Elite vertical grip
- MDT extra round holder
- MDT buttstock weight

$800 shipped (no original box)

22 Fat Rat with 90 SMK, 22 Fat Rat with 95 SMK, 6 Dasher with 105 Hybrid

Precision AR upper built on a Seekins SP3R upper. It's in a wildcat called 22 Fat Rat, which is basically an Ackley'd 22 ARC. It 's designed to mimic 6 Dasher ballistics in an AR-15 Platform. Muzzle threaded 5/8-24. Rifle +2 gas system. 329 Rounds on the barrel. Also have a boltgun barrel threaded for an Impact 737R and modified mag, if interested. Build for PRS gas gun, but can no longer compete due to a back injury.

-Seekins IRMT Upper
-Seekins IRMT 15" Handguard
-JP Enhanced bolt carrier group
-26" PacNor 6.5T 3 groove stainless barrel
-SLR 0.936 gas block
-Just under 300 formed cases (from Lapua 6.5 Grendel)
-JGS Reamer
-PTG Go and No-GO gauges
-Impact 6mm Muzzle Brake
-Whidden 6mm Fat Rat die set with 2 intermediate forming bushings (need a 0.251 final bushing)
-Modified Lee seating and Factory Crimp dies
-Whidden shoulder gauge
-Modified case for Hornady bullet comparator
-Brownell's bore guide
-One 17rd. E-Lander 6.5 Grendel Magazine
-Spare Rifle +2 gas tube
-JoeBob bolt saver

27.5gr. of H4895 gets 88 ELD-M up to 2945 fps.
28gr. of H4895 gets 88 ELD-M up to 2990 fps.
Fireforming load is 25gr. of H4895 @ 2673 fps.

$1900 shipped

Would consider the following trades;
-Dillon RL-1100 or CP2000 set-up for 223/5.56
-Glock 21 Gen5 MOS
-USP45 Tactical
-Eotech XPS3
-Seekins MCSR 10" M-LOK Handguard
-Wilcox NV mounts
-Streamlight TLR-VIR II
-TBAC Take Down 22 Suppressor 100% certificate

Q Plan-B mount for the AAC Tirant. Used once. Decided to go a different route. $90 shipped




-RCBS steel 25 ACP dies. $40 shipped
-Dillon XL650/750 7.62x39 conversion 21117 (includes 6.5 Grendel casefeed adapter) $110 shipped
-Swage It - Small Primer Only for Dillon XL650 $90 shipped
-72 50AE cases $25 shipped
-147 5.7x28 cases $35 shipped
-Hornady bullet puller collet #9 $15 shipped





Custom AR-15 Handguard. Project goal was to create a handguard that would allow up to a 1.8" suppressor to be tucked under it. Sling QD holes were also added. Needs to be re-finished. Mounts to a BAR compatible mount (included). Has some minor marks from the chick that should get hidden with a light bead blasting and cerakoting.

$65 shipped




-1/2-28 22 cal. muzzle brake $75 shipped
-JMAC Dead Air Wolfman 5/8-24 mount/brake $60 shipped
-Shockwave Blade Pistol Brace $35 shipped
-CMMG 4.5" 22LR AR-15 barrel $100 shipped




-Texas 1836 Glock 43x brown leather OWB holster and mag pouch $65 shipped
-Glock 43x kydex IWB holster and mag pouch $65 shipped
-Gen2 Sheild Arms G43x/G48 15 round magazine $35 shipped
-Griffin Armament 1/2-28 threaded G48 barrel $80 shipped
-Trijicon G43x/G48 HD XR orange night sights $100 shipped
-G17 night sights (came on used pistol - Believe they are Trijicon) $50 shipped
-Impact +1 S&W Bodyguard mag extensions (3) $20 shipped
-Vickers Extended Slide Stop for G43x/G48 $20 shipped
-Vickers Magazine Catch for Gen4/5 G17, 34, etc... $12 shipped
-Vickers Magazine Catch for Gen4 G20, 29, etc... $12 shipped




Tacsol .22LR conversion for G17/34. Runs well with recommended ammo. Five 10 round mags, four 15 round mags. Some still in packages. Spare parts.

$450 shipped

Would consider the following trades;
-Glock 21 Gen5 MOS
-USP45 Tactical
-Eotech XPS3
-Seekins MCSR 10" M-LOK Handguard
-Wilcox NV mounts
-Streamlight TLR-VIR II
-TBAC Take Down 22 Suppressor 100% certificate




MPA picatinni mount for Harris bipod. $60 shipped




6.5x47L barrels. Were on Surgeon actions. Both have +2500 rounds on them. $50 + shipping each


For brass, buyer pays shipping on whatever flat rate box they fit in. Will combine with other things.

125+ pieces of once fired Hornady 300 PRC brass. Fired from AI Bolt Rifle

70.00 shipped to lower 48
Lower price

For sale impact 737R action. 90 degree throw, cut for AICS mags, 308 bolt face, comes with new firing pin and spring that are installed. 2 extra firing pins, 1 new, 1 used. 1 new firing pin spring. Extractor claw and plunger and springs were replaced this year so there fairly new. You will get the old ones as spares. Also will receive a new bolt stop kit that was never installed.

1375 dropped to 1350 OBO

shipped to your FFL
PayPal friends or family or you pay the fees or venmo. If you have any questions at all or want more pictures let's me know.

Selling a very nice Kahles k525i. Scope is like new and glass is in perfect condition. Have the factory original box and it will also come with Tenebraex scope caps. ***SOLD*** shipped, no trades. Thanks.

I bought a Leupold HD MkII 5 7x35. Mounted it on a Remy action, 20 moa rail Sighted it in, did nicely, but when I checked I only have about 15.5 mils elevation. I called Leupy and the guy said thats just the way it is. I ordered a 40 moa rail, but it shows 5.83 additional mils. Other than getting a higher moa rail (not easy to find) what can I do to avoid needing to do a hold to reach past a mile?

So I recently picked up a Garmin Tactix 8 as I wanted to have an AB capable watch to connect to my AB Quantum app. In testing the two, I am getting two wildly different holds for the same profile and similar conditions set between the two. Anyone ever encounter this that might be able to provide some advice on what I am doing wrong?

Used hellfire brake, in very good condition. Less than 250 rounds on it. 30 cal, 5/8x24

$140 shipped

MDT PRS-Short single pull ckye pod gen 2 $525 shipped

Complete upper build list:
BCM upper mueller forged mark, does have BCM cut above gas tube hole in face or receiver.
BCM MCMR 8" handguard
BCM tube and gas block
BCM 9'' 300 blk barrel
BCM single side short latch charging handle
BCM qd
Tool craft BCG
$650 shipped (other accessories in pic not included)


If picked up local will give whatever ammo i still have left 60-100 ammo inc subs. Will make a deal on some 30 round mags as well. Located East texas.

I am evaluating ammo choices this off season. This season I shot SK LR. It did ok but the ES is wide and it’s running around 1120.

I’m debating going back to Eley because it was 1100 or less.

What does SK LR do out of your rifles?

This was out of an ACE 1:16

SPUHR 5001 35mm scope tube, 1.181” height and 0 Mil.

$SOLD Shipped

Trades Welcome

PayPal Accepted

Selling this guy for $100 $85 $80 shipped. Comes with one spacer.
PP, Venmo, or USPS MO.

Top to bottom, left to right:

UTG 3-9X32 AO MIL-DOT $100 $80
Vortex Crossfire II Scout 2-7X32 Duplex Sold
Vortex Crossfire II 1-4X24 Duplex $130 $100
Vortex Spitfire 1X Prism DRT (MOA) $100 $80 Sold
Bushnell Pistol Dot $80 $70
Konus Pistol Dot 4MOA $60 $50
Swampfox Kingslayer Pistol Dot 3MOA Sold
Vortex Venom 1-6 AR-BDC3 MOA Reticle $200 $180 Sold


All prices are shipped.
PP, Venmo, or USPS MO.

So I just started PRS a couple of months ago. I was fixated on how people went from stage to stage collecting their data during pre stage. I was also fascinated with their setups. A couple weeks ago I decided to put together my own spotting setup. Looking at what everyone has I noticed that some people had ready made tac tables and some had home made or 3d printed ones. I had some experience building camera rigs and decided I can use some parts like a cheese plate to build the platform. Now this is just the first iteration and since its modular I can add or subtract parts as I go. I can also do a sliding plate underneath the main platform in case I need more room or If I decided to add a spotting scope. I also 3d Printed a weather vane for the kestrel If I decided to get live wind data. But for now I see myself using the windicator just to see where the wind is blowing. if there are any ideas as to what else I should add or what would be more practical, I'm all ears. Afterall, you guys are the experts. i just love to tinker.

Selling my Accuracy International AXSA in Elite Sand. I've owned it for several years, but the rifle is still in fantastic shape. It includes the rifle and the following items:

6.5mm Creedmoor 24" 1:8" 5/8"-24 Elite Sand Proof Research Barrel - pictured on rifle ~100rds on it
6mm Creedmoor 26" 1:7.25" 5/8"-24 Elite Sand Bartlein Barrel ~800rds on it
3x Elite Sand 10rd Magazines
MLOK handguard with ARCA rail in Elite Sand
KeySlot handguard in Elite Sand
Thunderbeast CB Muzzle Brake

$5500 shipped and insured to your FFL
Not looking for trades

Is RKB Armory still buying rifle scopes I have sent them a couple of emails with no response.

Portland Oregon — A 26-year-old bartender at a downtown sports bar was arrested Saturday night after what police described as a “tip jar tantrum” during a packed football game.

According to witnesses, Jessica Miller had been pouring drinks nonstop for nearly an hour when a group of fans ran up a $300 tab but left only $2 in change on the bar. Miller allegedly snatched the bills, held them in the air, and shouted, “That’s not a tip—that’s a slap in the face!”

Patrons say she then unplugged the jukebox, silenced the game, and began pacing the bar while chanting, “Twenty percent or go home!” The scene escalated when she started pouring shots of well whiskey onto the floor, declaring them “sacrifices to underpaid staff everywhere.”

Police say Miller refused to unlock the bar cooler until “every customer pledged loyalty to tipping culture.”

Some regulars hailed her as “the voice of service workers everywhere,” while others said she had turned “happy hour” into “handcuffs hour.”


She seems nice.

Trijicon RM06 in new shape never been mounted and not a mark on it
comes with AD co witness AR mount and Glock mounting plates
$350 shipped
Aimpoint Pro in great shape some slight wear on the mount and bat knobs from safe storage otherwise everything else is clean and has no issues
$310 shipped

Does anyone know who manufactured the bottom metal for the removable mag version of the m24a2 and which magazines it will take ?
I assume the screw size on the mars rail was 840?

Knights RAS rail
P&S bottom
Comes with a bunch of grip panels VFG and case
It's clean and not beat up
$200 shipped

Post up some of your favorite movie one liners.


I'll get the ball rolling.

Login to view embedded media

I saw an "All Ackey" thread, but nothing specific to just the 223AI.

Fire Forming load
LC Brass - 1x fired and prepped to FF
CCI 450
IMR8208XBR @ 24.0gn
Berger 80.5gn seated at 2.485" COAL
22" 7 twist Rock Creek #4
Defiance Deviant
Jon Beanland built
5x @ 100yds measured 0.2455" CTC