Selling my custom 300 PRC - $3k buyer pays shipping (or willing to meet within 3 hours of KC).

Barrel has about 700 rounds on it and is cleaned very regularly. About every 50 rounds.
I have dope out to 2911 yards (starting at 200y - 2100y and then to 2911) that I will be happy to provide.
I will also be happy to provide load data for Berger 245's and Hornady 250gr A-Tips.

I recently won a local ELR match with this rifle (King of KC). The rifle started to perform extremely well at long distance (2k+ yards) once I switched to 245gr Bergers from the 250gr A-Tip. Unfortunately for me, that was at the tail end of my ELR season. First round impacts at 1900 and 2100 yards in the last match I shot and somewhere between 20-30% hit ratio at 2911 in the couple matches prior to that. Probably higher if I was better at reading wind.

Current load has the 245gr Berger LRHT coming out at 2805fps average with an SD around 7-8. This load could likely be pushed further as I have encountered 0 pressure signs at this point but it works really well so I haven't bothered. Papers about .6 MOA with a 5 shot group from a cleaned and fouled barrel. It should be noted, this is with the suppressor on (SilencerCo Hybrid 46). If you intend to shoot this unsuppressed, you will need to verify/tune the load.

MPA BA Chassis (Tungsten)
Zermatt Origin Long Action
28" 1:8 right twist barrel, chambered by Straight Jacket Armory (4/15/24), cerakoted black to match action.
Trigger Tech Diamond 2 Stage
ERATAC 0-20 adjustable scope mount with 34mm rings (non-qd)
Accu-Tac HD-50 bipod (arca)
SilencerCo ASR muzzle break
Magpul PMAG 5 AC L magazine


I'd let go of all of the brass, bullets, dies with it for an additional $300. I'd also be willing to sell the following separate from the rifle for a slightly higher cost.
If you're local and interested in this stuff, I'll throw in like half a lb of Retumbo I have left and some Remington magnum primers.
220ish 250gr Hornady A-Tips
50ish 225gr Hornady ELD-M
120ish 215gr Berger Hybrid
60ish 245gr Berger LRHT

300ish pieces of Hornady brass
46 pieces of ADG brass

Hornady match sizing die (with bushing) and seating die


I don't really want to sell the glass as that's going on my PRS rifle but if you insist on taking it as a whole package, I'd do an additional $1k on the nose for the Athlon Cronus BTR Gen 2. In it's current configuration, the scope mount stays at 10mil which gives me 30mil of dialable in the scope with a 100 yard zero. You can then add the remaining 10mil of elevation in the mount for a total of 40mil of elevation before needing to hold over.

I would most likely continue ELR next season except my son wanted to start shooting PRS with me and I do not have the time/money to support 2 shooters in PRS and continue with ELR. I may be interested in production class 6gt bolt action rifles (eg GA PPR) as trade options, nothing custom though as I am looking to switch to production class in PRS next season.

I’m about to give up on getting a TBAC Magnus K RR, can’t find one anywhere. So, leaning towards an Abel Theorem or Theorem-S, possibly the Abel Biscuit. Looking for recommendations on the Theorem vs. Theorem S. Is it worth it to wait for the TBAC?

Suppressor will go on my MPA Matrix Pro, 6.6cm. I shoot mostly recreationally but will be shooting some PRS also.

Like new condition. I think I looked through them twice on the back deck. Never been in the field. $1300 $1200 $1000 shipped to your door. Not looking for any trades at this time. Thanks.

100 qty - 6.5mm 130 grain AR Hybrid OTM Tactical - sealed box
100 qty - 6.5mm 100 grain Match Grade Target Boattail - opened full box
$50 shipped to your door. Not splitting up and no trades. Thanks.

Sold

Like new trijicon Qloc 34mm mount, 1.06 height, $150 shipped

Like the title states, looking for a SAC Alpha Dasher sizer. New, used is fine too..
Lemme know if you have one ot if you know where to get one. SAC says about a month or more lead time as of right now. I bought a dasher barrel with alpha reamer specs and totally forgot to order the die set a while back, so I'm pretty f-ed once my brass is fireformed.

Thanks

I put this together to go on an elk hunt then needed a bit of emergency spinal surgery. I won't be using anytime soon. Zermatt Origin action, proof carbon fiber barrel 24, was altered from a tl3 to fit origin. Manners EH1 carbon fiber stock, triggertech diamond flat, hawkins bottom metal, with accurate mag. I can sell with or without leupold mark 5 TMR reticle with Arc rings. As it sits with scope and 4 rounds without bipod is 9.6 pounds (bathroom scale). Rifle only 3k, rifle with scope/rings/bipod 4700. Roughly 200 rounds on rifle. Questions please ask no trades. Comes with 30 rounds nosler loaded ammo 10 cases, 142 federal brass and Forrester dies. I can swap to a manners LRH stock for 200 more if you prefer that stock.

The Seekins PH3 was announced looks like a lot of nice features for the money.
Login to view embedded media

shipped FFL to FFL
Zelle (no comments) or check only (cash FTF reasonable distance)
21” Blaser barrel cut, crowned and threaded 5/8x24 with TBAC brake timed and torqued by Precision Rifle Works.
150 ish factory rounds fired using TBAC ultra 7” (can not included).
Federal factory ammo used exclusively 190 LRX @ 2850 FPS 1/2 moa rifle.
Area 419 Pic Rail mounted, great for my bipods and Tripods.
I used this setup to Kill lots of Elk 12-700 yds, deer, antelope, Alaskan moose, mountain goat (800 yds) and yes, my only Wolverine.

Moving lots more goods 6.5cm DT conversion, RRS acc, etc- soon to be posted, putting together $$ for a bunch of upgrades for my F350.

Looking for $250 Shipped.

Garmin Xero C1 chronograph. Asking $500 shipped CONUS. No scratches. No issues. Light use. *No trades.

This item is brand new, it's never left my house, I never attached anything to it. Absolutely brand new bought from Scheels during the spring time. I have too many tripods (5 and a 6th on the way), I have to sell some. This is the Fatboy tripod 2 section inverted legs. It will be shipped in the box it came in, scheels did not ship this in an outer box (if I can get one I will). It has a very well padded thick bag it comes in.


Asking $625 —> $600 shipped and insured

NO TRADES
PPFF preferably venmo Zelle check MO.

Aimpoint T2 in excellent condition (really this is in like new condition), MOUNT IS GONE and is not included...again the scalar works mount is not included. See pic of bottom, just one pinpoint mark in the undersurface where the mount mated, barely noticeable but I mention everything for full disclosure.

I mounted this red dot and NEVER shot it.... ever. It sat on one of my ARs which I really don't shoot b/c bolt guns are better ... I'm the original owner and bought it in 2023 so it's still under 10yr warranty. Original boxes and packaging included as shown. I can ship it as is, or disassemble it.
Cross listed on AR15.c0m

$700 -->$650 shipped and insured ...
NO TRADES AT ALL
PPFF or regular and you pay the fee, Venmo, Zelle ok as well or mailed check/money order.

I just purchased an AT-X in 308w last month and I'm looking for additional 10 round magazines.
I see MH and EO have two different versions of AW magazines.
Model # 6677 and 0726.
Which one is the correct magazine I should buy for the AT-X?
Thanks in advance.

Leupold Mark 4 ERT 6.5-20×50 M5A2 Enhanced Sniper Rifle Scope with TMR reticle. I sent this to Leupold a few months ago just to have them look it over. What you see is what you get (minus tac pillow)

$1550 shipped

Please click here to view and purchase.

**

**

At the range prior to my Tikka .223’s first shot, I’ve been removing the oil leftover from barrel cleaning. But I’ve been reading about how leaving this oil in the barrel may help prevent copper buildup from the first few shots, and that some shooters will run a patch with traces of graphite down the barrel prior to shooting in order to also prevent coppering. Has anybody observed increased copper buildup or long tern issues from a dry barrel as oppossed to an oiled one or one with a trace of graphite for the first few shots? Thanks

Hey Guys,

We have mentioned and shown off pictures in the past of our Integrated ARD scope caps, or what we are calling iARD's. Well, that is finally coming to fruition soon, and I'm giving you lovely folks on Snipers Hide a few weeks early access before these get announced on all the other platforms. We only have a couple brands live on the website currently, but inventory is essentially ready to rock for all the models of scopes that we currently have standard caps for. Current brands are NF, Zeiss, ZCO, and some Vortex coming shortly. If you want to try these out and don't see the brand/model you want, reach out to [email protected], and Darlene can help you out.


We don't ever release something and immediately discount it with a sale, but Snipers Hide members get 10% off every MKM and Audere brand product on our website with coupon code SH10.

Photo Cred: Sharp Shot Studios on IG




Let us know what you think. Thanks!

Brand new Nightforce Atacr 7-35 black - mil-xt

Box opened for pictures, never mounted.

$3300 shipped and insured.

Can someone explain the True Long Angle at work here ? .. Passing of the anti CBDC .
BECAUSE NOTHING seems to be ever Passed truly benefiting Public prosperity. Over the DC Beltway Party cartel acquiring control and Money.
.

2 boxes of 100ct Hornady 6mm 110gr Atips.

$145 $120 shipped conus. Payment Zelle, Venmo, PP F&F, or USPS money order.

Selling my EDC. Sells as shown. See the pics for details on the salt from actual carry and indoor training. Performs flawlessly. Comes with (4) 15 rounds + magazines. Will ship with OEM Glock case with all OEM materials and tools. *Serial # edited out on pic for privacy. It is there!
Only selling so I can fund a new scope for PRS.

FOR SALE:

GLOCK 19 GEN 5 with these upgrades done -

• BARREL: True Precision with threaded muzzle and protector. Stealth Gray PVD Color - Just under 300 rounds on this barrel and gun.
• NIGHT SIGHTS: Trijicon Bright & Tough Suppressor night sights. Installed by Maple Leaf Firearms of Celina, Texas.
• SLIDE: OEM slide cut for the 509T and Stonewashed Nitride treatment done by Maple Leaf Firearms. This is not Cerakote.
• SLIDE LOCK AND MAG RELEASE: Vickers Tactical
• OPTIC: Holoson 509T Gen 1 Red. Perfect glass. Perfect solar screen. Shows only wear from carry. Very clean. Will ship with the OEM box and all materials.
• GUIDE ROD: Centennial Arms Stainless Steel. 18 lb. weight.
• STIPLING: Custom done by Lew's Firearms. Central City, Louisiana.
• TRIGGER SHOE: Tyrant Tactical I.T.T.S.
• MAGWELL: DAWSON PRECISION. see pics for salt.
• MAG EXTENSIONS: (1) Dawson Precision Bottom Plate, (2) Taran Tactical +4/5's, (1) Glock +2. see pics for salt
• Will not ship in OEM packaging.
• *I am happy to provide additional pics or take a face-time call for proof of life or additional concerns.

SELLING PRICE: $900 obo shipped and insured.

Accepting PayPal FF(NO NOTES) or Zelle(NO NOTES). Paypal G&S buyer pays fees
Please feel free to make me an offer if you wish. The worse thing I can say is no.

Magazines will not ship to a banned state. No your own state laws!!

NOTE: All required legal steps will be followed. Will ship from my FFL to your FFL.
Will ship out first thing next biz day after my end of the FFL transfer is completed.
I must secure appropriate packaging from my local Pack-N-Ship and required legal steps to ship via carrier.

PM me first to avoid scammers. I will not PM you. No business in the thread.

I have an idea bouncing around in my head and wanted to get a few opinions.

My favorite rig is based on a 12.5" Criterion Hybrid barrel. Next to my "precision" rig, it's my most accurate setup. It almost seems like it goes on autopilot everytime I squeeze the trigger.

Anyway, I've never been wild about shooting suppressed, but last weekend, I got to shoot a rig with a Cobalt Kinetics suppressor on it and now, I can't get it out of my head.

What I want to do is get the direct thread model (it has an extra baffle in it), which is made of titanium and pin and weld it to my 12.5 to make 16".

Is this a mistake? When I shoot the barrel out, how ugly is it going to be removing the suppressor to put it on another barrel? I've pinned, welded and removed a lot of muzzle devices, but never a suppressor.

4 AI marked 300WM mags. Mk13 surplus mags, $45 shipped per or $40 per if you buy all 4.

Payment via PayPal F&F, Zelle, Venmo, USPS MO. SOLD