Sticky this for 10mm Auto load data



I'm doing load development for my Gen4 Glock 40 MOS with RMR RM07 Gen2 with 200gr hard cast bullets from Montana Bullet Works... goal is bear loads.

I purchased .401 WFN-GC from them for bear loads and their WFN-PB practice bullet. Both are hard cast.

Had a lengthy conversation with their bullet guy and he said their WFN-GC has killed many bears and he would take it over a BB or Underwood any day. I'm not going to pretend I know what I'm talking about or exactly what he said because I don't remember 100% but he talked about their mixture vs high antimony. Either way, MBW comes highly recommended.

Today was my first day playing with loads. I loaded up 5ea 6.0-7.2gr in 0.2gr increments n350 with the 200gr Montana Bullet Works HC WFN practice bullet they sell. HiTek coated. Sig nickel brass and CCI LP. Stupid accurate at 10yd out of my factory Gen4 Glock 40 MOS with RMR RM07 Gen2. Don't have any speeds but I will tomorrow. They shot soft and the higher charges were probably in the 1025-1100 range.. zero leading issues. Nice and clean

Guy MBW told me to shoot my same load with the 200gr HC practice bullet and the WFN-GC.. he also said dont worry about trying to get them super fast. He said 1100-1150 is fine they will penetrate great at that speed. waiting for some longshot to arrive to load a good 1200fps bear load with those.

I did chrono the underwood 200gr HC round out of my gun and avg was 1200.. they also started leading the last 2" of my barrel

Also have a Bar-Sto match barrel being made for this Glock 40. Once it's ready they are gonna call me to send my pistol in to have the barrel custom fit. Mostly doing this for better case support over factory glock barrel.with hotter bear loads but I'll take the increased accuracy as well.

Here the Montana Bullet Works hardcast 200gr WFN-PB HiTek coated practice bullet

Login to view embedded media
Login to view embedded media
Login to view embedded media

Here the Montana Bullet Works hardcast dangerous game 200gr WFN-GC bullet I'll be loading to carry in the woods



Login to view embedded media
Login to view embedded media



Here my targets from yesterday with VV N350 and the 200gr WFN-PB @ 10YD



6.2GR


Login to view embedded media



6.4GR


Login to view embedded media



6.6GR


Login to view embedded media


And here is factory Underwood 200gr hardcast @ 10yd 1200fps on labradar




Login to view embedded media

Zeiss Sport Optics Giveaway

Every month is as, or more, exciting than the last. We are thrilled to have the new Zeiss Conquest HDX LRP 15x56 Binocular with MRAD Reticle for our giveaway on May 7th.

The ZEISS Conquest HDX LRP 15x56 is made to turn competitors into winners thanks to its MRAD Reticle. It is designed for precision rifle shooting, featuring a milliradian reticle for accurate target assessment, a reticle leveler adjustment, and dual diopter adjustments. With 15x magnification, 56mm objective lenses, and tripod compatibility, it provides bright, sharp images for competitive shooters.

Long-Range Precision (LRP) Designation
Tailored to enhance the performance of competitors in Precision Rifle Series (PRS) and National Rifle League (NRL) events.

Reticle Leveler
ZEISS has incorporated a lever at the top of the left ocular for easy and quick reticle leveling, allowing observers to accurately adjust and maintain a level reticle.

Integrated Milliradian Reticle
An advanced milliradian reticle etched onto the internal lens, helps shooters assess bullet impacts, lead moving targets, and make wind calls in competitions.

Reticle Design
The reticle features a 'T-style' and 'tree-style' design with a floating center dot, offering 10.0 MRAD of windage, 5.0 MRAD of drop, and precise MRAD increments for accurate adjustments and target evaluation

Dual Diopter Adjustments
The binoculars feature two locking diopter adjustments – one for sharpening the reticle and the other for achieving a focused view across the entire field of view.

Tripod Compatibility
The binocular has a ¼-20 tripod adapter port and includes an Arca-Swiss compatible adapter for stable viewing, especially at high magnification.

High Magnification and Brightness
With 15x magnification and 56mm objective lenses, these binoculars provide a large field of view and bright, high-quality images in any environment.

Rugged, Adjustable and Removable Eyecups
The adjustable, comfortable eyecups offer four positions and are removable for easy cleaning and replacement.

Specs:
Magnification 15 ×
Effective lens diameter 56 mm
Light transmission 90%
Exit pupil diameter 3.7 mm
Twilight factor 29.0
Field of view at 1,000 m (yds) 80 m (240 ft)
Subjective viewing angle 69° Ww
Close focusing distance 3.5 m (11.5 ft)
Diopter adjustment range − 4.0 | + 4.0 dpt
Exit pupil distance 18 mm
Pupil distance 54 – 74 mm
Lens type HD
Prism system Abbe-König

This Months Winner is Donald R. of LRH

Congratulations Donald

Remember to enter our May drawing for your chance to win the amazing newly released Zeiss Conquest HDX LRP 15x56 Binocular with MRAD Reticle

It is our pleasure to bring these drawings to you each month to show our appreciation for all the support that we receive. Just our way of saying thank you.

We would also like to take this opportunity to thank the monthly winners for posting reviews of the products they have won. The forum members value your opinions, as do we.
Please go to our web site www.cameralandny.com and Enter To Win. Past entries will not be in this drawing. To keep the drawing available to those that continue to have an interest, each contest winner will be drawn from entries for that contest period.

Are you our next winner?

What are you waiting for? Just go and sign up. There is no purchase required and we are not selling your info to anyone.

Brand New Hornady Iron Press Kit With Auto Prime ......This is the Full Kit not Just the Press ......Cheapest I've seen online is 650ish ........... sold Shipped .........

Hello All,

How are you torquing the #2 action screw? It looks to me that you'd have to use a ball end bit but, wouldn't that make the torque required to meet the spec higher?

Saying it another way, do ball end hex bits apply the same force to the screw for a given torque setting on the wrench as a regular bit?

Thanks for the replies!

I am selling a Remington 700 LA (Std bolt face), complete with bolt, bolt release, trigger, recoil lug, hardware, and bottom metal. This action was worked on by Score High Gunsmithing in Albuquerque, NM; however, I didn't have it done, so I can't say exactly what they did. The face of the receiver definitely looks like it has been trued, and the lugs have been lapped. They also pinned the recoil lug. Trigger breaks right at 2lbs.

Must ship to FFL from an individual. $550 shipped, PPFF preferred. I will also accept personal check or MO, but will hold item until clear and/or money in hand.

Seekins 34mm low rings

I have 2 sets for sale.
$100 shipped/insured each

Aimpoint Comp M5 in a Unity Fast Mount. Comes with front and rear clear caps. $700 + ship.View attachment IMG_2346.jpegView attachment IMG_2347.jpeg

I picked up an Armasight Sidekick 640 to play with, and it's got alot of neat features for a little unit.

They recently sent out a firmware update for the device, and it's actually stoopid easy to install. Seems to fix a few minor things... In my case, the B2 button would no longer power the unit down, although it worked fine the rest of the time. After the firmware update, everything is GTG.

The ONE thing that would be nice on the Sidekick would be having an Edge Detection / Outline mode. Especially, if the device is used with a PVS-14... which Armasight goes to great lengths to sell bridges and their own PVS-14 for...

Armasight! Why is there no Edge Detection mode on the Sidekick 640?

Hello gentlemen,
after my last shooting session I measured my cases and I find some differences on headspace.
I tested some charges and the headspace are differenti from the low load to the ho load but from 1.4710" to 1.4700"

So I've made a resetting on the Forster FL Bushing sizing die for a 2 thou down from the fired case headspace, assuming that the 1.4710" of the hi loaded case are the start point.

My scheduling are the following:
- Bump the shoulder without the bushing for obtain the 2 thou of headspace (only for One or two case as reference).
Check on the chamber, ok!
- insert the bushing and resize the neck.
Check on the chamber, ok!
The bolt fall down free.
- expand the neck with mandrel.
Check un the chamber, ko!
The bolt don't fall down free, need finger help.

The headspace of the resized case are 1.4690"

I think that the mandrel, when open the neck, open also the apical section of the shoulder and change is angle.

If I think wrong can help me to solve this issue?

Thanks

New, never fired Norma brass just been laying around for projects never done.

200 pieces of 300 WSM brass: $300 to your door

100 pieces of 7 SAUM brass: $150 to your door

Thanks!
Conrad

Selling a brand new Bartlein barrel, 1:9.5 twist ModBB, 38” finished. Barrel is currently sitting at Vestal’s. Spec sheet is attached.

Asking $950 shipped or trade for .338, .375 and .308 similar barrels.

I have one left. unfired KAC sr15 with the older E.3 bolt. this upper is new but did go to retro arms for pin and weld on the muzzle device. Cleanest P/W I've ever seen. $1500 paypal shipped.

I’m looking for a trijicon tenmile 3-18 ffp mil/mil

Login to view embedded media
As many of us know, most AR-10s are overgassed from the factory. The most controllable way to deal with that is an AGB, but not everyone is willing or able to install one. Enter the Bootleg adjustable BCG. They make them for AR-15s too, of course, but this is the DPMS pattern BCG. TLDW; it works well. My BCA-10 is so overgassed without it that it stovepipes, even with a flow through can. In fact, the rifle runs fine without a can and the BCG set to full suppressed.

Letting another spare stock go, Manners Pro Hunter w/mini chassis. You will need an M5 DBM. Inlet for R700 SA, barrel channel is proof Sendero. Color is Altus granite forged camo. Asking $900 shipped. Stock is in great shape, like new. Mounted a barreled action in it and only shot once. Been sitting in the safe since then.

Accept USPS money order or PayPal FF.

WTB: Trijicon Tenmile 3-18 MRAD

Looking to spend $850 -- Send me what you've got.

**I won't PM you first, anyone else doing so is a scammer** If you have issues PMing, comment here first.

Want to trade? I have a P229 Legion (non-OR) that I'll trade + cash to you.

Making a table for the wife lately and Saturday, I did what we are never supposed to do. No gloves on, I was pulling a 6' board through my table saw and I found the blade....

My safety glasses had dust all over them and I just couldn't see the blade that well I guess. my wife was helping catch the boards and watched me do it too and she also said that she didn't think I was that close to it. Yes, I kept working and got all of them ready to join because I'm a man.

Of course this is just one of many accidents. I once caught a metal chuck that came off my lathe with my freaking bear hand (just a reaction to save it from hitting my lathe bed)and had a steel splinter inside my palm for a few days before realizing why it kept hurting so bad. i got it out with a magnet.

Mashed off the end of my left thumb between gears or a flywheel and starter on a log splitter when I was 17, and I've cut myself many times.

So what are the coolest injuries yall have done? Must provide pics or it didn't happen!!!

table and finger for proof

Redding Type S Match 6.5 CM Dies

• Neck Bushing type Full Length Sizing Die
• Includes one neck bushing: please specify the NB diameter you want included
• Micrometer adjustable Seating die: includes VLD seating stem plus typical seating stem

$125.00 shipped CONUS
Zelle or PP/FF

Never really saw much use. Maybe has some slight ring marks, but they are hard to see. The Glass is excellent. No box but comes with sunshade and Vortex Defender caps. Purchased new by me.

$230 Shipped. PPFF preferred.

Like the title say mdt acc in great condition has front internal weights and buttstock weights and dampers. Also has a full length arca and two forend bridges. REM 700 pictured in mac bros evo2
$1250

I built an AR9 some years ago using a quarter circle 10 reciever, barrel, and jp bolt. I couldn’t get my favorite Larue MBT triggers to work so it ended up with a milspec from the spare parts bin.

I have put a few hundred rounds through it and it started to burst fire at the range so I pulled it apart and inspected the trigger but didn’t see any issues. I replaced with another milspec and same thing happened.

I see there are PCC specific triggers, is that because normal AR triggers don’t work? Is there something else I need to look into as to why it keeps burst firing?

I have built a handful of ARs without issue so I don’t believe it’s an assembly problem, but anything is possible.

Check out the dealer we have on these European spotters. Call me to order 504-565-0629

Selling Ruger M77/17 modified by Clark Custom Guns

I purchased this as a complete 17 WSM rifle then sent it to Clark Custom Guns and had it worked over/tuned it up with a custom fluted 21.5" barrel with 1/2-28 threads, tactical bolt knob, extended mag release, and a Boyds stock with an adjustable cheek piece that has been glass bedded. Does include a Weigand picatinny rail adapter (not shown). I will include the remaining 5 of boxes of Winchester 20 grain ammo.

Has a total of 200 rounds down the tube as of the target shown below. It has been sitting in the back of the safe and has spent more time being moved around in the safe than being used. After scratching the stock with a bolt from another gun in the gun safe, I decided it was time to get rid of a couple things. (Scratched both sides below the action, shown in pictures)

Scope with rings NOT included but will consider selling at additional cost... SHV in mils.

Shoots about 1 MOA at 100 yards with Winchester ammo and KG Made can. (only ammo I had on hand).

Price Dropped 09.23.24 to: $1,400.00

Radian Upper with handguard - $600 shipped


Trades: Baja Designs Onx6+ 30” Arc, Baja Designs Squadron Pros x 2 or 4

Have an IMI 308 galil AR with the box/cleaning kit/ manual and stuff. Always wanted an m40a1. GAP rifles are looking good. Curently have an m24 so an A1 should go good with it right? Stupid idea? What are galils brining nowadays?