Hand loads 22 ARC



62 Eld VT, has anyone had issues getting this bullet to produce good groups?

AR platform 16”

Faxon 6.5 Grendel BCG

Quality barrel

The rifle in question will shoot the following sub Moa.

• 53 Gr Vmax 2900-3400 fps all good
• 73 Gr Berger BT Target 2750-2900 fps
• 75 Gr Eld M. 2800-2900 fps

The rifle will not shoot the 62 Gr Eld VT

I have attempted 3 primer types. Cases are a mix of Hornady 22 arc. Hornady 6.5 grendel converted.



Powders used in various charge weights

• CFE223 - worst groups
• Varget
• N135
• H135

Going through the gun room, I've got lots of extra stuff to get rid of...

Triggers:

1) Geissele SSA (Super Semi-Automatic) Trigger, SOLD

Comes with a Larue Trigger Action Chassis (mock trigger housing) a magpul grip and standard safety

(https://geissele.com/super-semi-automatic-ssar-trigger.html)

2) Geissele Super V Trigger, $135 (Basically the predecessor to the Super 3 Gun Trigger), SOLD

Comes with a Larue Trigger Action Chassis (mock trigger housing) and a generic grip

3) LMT (or LMT clone - not sure), 2 stage curved, (See pictures), $85.00

(Looks exactly like this: https://www.primaryarms.com/lmt-axle-s-a-euro-two-stage-ar-trigger-group)

Larue Trigger Action Chassis (mock trigger housing), and a Timney Ambi safety.

Triggers 1 & 2 are SOLD.

3 Unknown trigger (LMT (or LMT clone - not sure)), 2 stage, curved, probably 2lbs and 4.5lbs

Chambered for the .327 Federal magnum which was meant to push some .357 mag level numbers but adding a 6th round in a j-frame.
Also shoots 32 H&R magnum as well as 32 S&W long and short ammo.
3" + the "power port" comp to help with the full-blooded .327 loads. Discontinued and rare.

This particular specimen has had some work done by Dave Lauck of D&L Sport

barrel trued to frame
black nitride refinish
Orange tritium HD front and square notch rear sights (installed 2024)
Carry trigger job with full-power spring


Comes with Lok grip G10 grips. and Dark Star Gear holster.
160 rounds of Fed .327 mag HydraShok
20 rounds of Fed 32H&R mag hollow point


Asking $1990 shipped for the pistol, ammo, holster as shown
Pistol must go to FFL via UPS air
Discreet paypal, Zelle, or cashier's check (no interest in trades at this time)

I have a few mostly new MPX parts here since I sent mine to be SD converted.

Lancer 14” carbon handguard like new - $225

OEM 16” handguard - $180

Not pictured - 16” factory barrel with TTI brake, shoots very well. Just the barrel no gas block assembly -$300

the short barrel and 8" midwest handguard are gone

Aftermarket M-LOK siderails for Gen 1 and 2 JAEs. These allow for the use of M-LOK attachments as opposed to the original rails that only allow use of the proprietary attachments.

$sold shipped.

I have a set of chargemasters I'd like to move on. $350 shipped for the pair. Has the insert on the powder dispenser nozzle.

Brand new. I bid on 2 on eBay and end up winning both and I don’t need 2.

$600 shipped to your door in the USA.

Pm call or text me. 815-878-8255

PP F&F. Will UPS it out the same business day.

Got an older T3 lite 6.5x55 I gifted to my Dad 15+ years ago. Dad has bought a bunch of rifles since, he used it for 5 years or so, probably has 1000 rounds through it. He bought all the grandkids t3x 6.5 Creeds, but decided to give this one to one of my kids.
Problem is my son relates sound to recoil. He'll shoot my suppressed 6.5 Creed all day, but his brothers unsuppressed 6.5 he says kicks horribly.

Was going to have it threaded 5/8-24 for a can. Started thinking about it, wondering if anyone here has had any experience. Worried the hammer forged barrel might go to hell accuracy wise.

So would you roll the dice and thread it? Or should I just suck it up and pay the $800 for a re-barrel. I think there was a guy in Bozeman area doing pre-fits but I can't remember who it was.

I joined a few months ago. Lifelong Hunter and gun enthusiast. I am new to the suppressor and Thermal / night vision game and am hooked on both now. Mainly here to read, learn and research. I love the site. RTR

Payment via discreet Paypal FnF or Venmo. Shipped via USPS priority.

Surefire MB68AR Muzzle Brake. Overall in decent shape but does have some dings from use. Threaded in 5/8x24. $200 shipped.

Just picked up this awesome AXSR chassis for my Impact BA. I've learned to expect fitment issues with these trigger hangers so here's my question:

The chassis has a "magazine stop" if that's what it is called. I removed it because the front of the trigger hanger interferes with it. My single stack mags feed flawlessly - no issues at all. However, without the "mag stop", a little upward pressure on the mags place the feed lips in front of the bolt and it cannot forward travel. Not a big issue, but I am asking if AW double stack mags and their different feed lip geometry would allow the bolt to pass over?

I've had some custom builds where upward mag pressure touches but does not impede forward motion of the bolt, and one or two that did, so this is not new to me. I had AW mags a long time ago, but my 6.5cm rounds kept springing out into the dirt so I switched to single stack ever since.

WTS NEAR 34mm Alphamount
$200 $175 shipped SOLD

If paying by check, it must clear before shipping. I have PayPal and Venmo ,you cover fee if you choose secure PayPal.

Very Hard to find and long Discontinued Spuhr SP-4016 CantiLever Scope Mount. 34mm Rings and 1.50" Height and 0 MOA Cant. Perfect for Offset AR15 or AR10 Platforms.


$400 Shipped.

***Reduced to $375 Shipped TYD***

F/S MDT Ckye-Pod gen2 single pull standard . Near new condition. BTC clamp.

$500 obo shipped CONUS.

I’m selling my KRG W3 and looking for a chassis that checks certain boxes. My goal is to have a chassis under 2.25lb to shoot NRL Hunter lite division but can be weighted down to ~7lb for PRS and 22LR competition.

My barreled action, trigger, scope, etc weight in at 9lb 5.2oz so pair that with an MDT mountain bipod I’ll be at around 9lb 10.8oz.

My current plan is the XLR element with smokes carbon fiber buttstock. I’ve also looked at the new MDT LSS gen 3 but am not sure I can get the total chassis weight under 2.25lb. The modularity is intriguing though. I’d like MPA but even the Lite is too heavy. Vision makes a hybrid which seems very similar to the element but doesn’t have the ability to add internal weights. Unltradyne is the same issue, no internal weights. Any other suggestions?

Will need rubbers on the side of the clamp replaced. Great shape otherwise. Moved to a tactable. 40+shipping

Selling a Halo XRF for a friend. Operates as it should. Was his main scope for 1 season and backup for 2 seasons. He is an NVISION dealer and the scope will be sold as a demo with full warranty. Comes with a bobro mount.

Selling an old scope that I had on a 22 AR. It’s a Cabelas LR scope 4-16x44. 30 mm tube MOA turrets and reticle. SFP reticle. I use MRAD now so no need.

Mounted in a Cabela’s single piece cantilever mount. No trades unless you have a Vortex Diamondback scope with MRAD, would be plus cash in my end.

$200/obo, buyer pays shipping

Up for sale is my like new, 1994 Leupold Mark 4 M1-10X with premier reticle conversion done sometime in the early 2000’s. This is an extremely hard to find optic, not even taking into account the like new in box part of it. Box isn’t in the greatest shape but it’s there.

$1500 shipped
PayPal F&F, Venmo F&F only.

Brand new in the baggie.

I'll cover shipping & shipment insurance.

No trades. PayPal, Venmo, and Zelle will be accepted as payment methods. Friends and Family or the buyer must pay all fees for a 'Goods and Services' transaction.

The first "I'll take it" in this thread gets the item stated.

$30

Ended up with a 50% off any FDN-17X or FDN-25X scope. I picked up used a straight 10X which I was really wanting instead off of the forums. So this is catch and release. Good until 10/25, 250$
Z

SOLD

$425, shipped within USA. No international shipping.

RRS Anvil 30 Arc head as described here: Anvil-30 & Two Vets conversion bowl as described here: Conversion Bowl

First posted "I'll take it" in this thread trumps any PMs. Venmo or certified check please. Thanks for looking and please let me know if you have any questions.

/Steve

​

Has anyone used either the bell & carlson or hr precision M50 style stocks for the howa mini?

I'm wondering if either of them have the thick and weird palm swell that the traditional remington 700 pattern ones did.

Proof Research barrel for RimX
21.25”

$420 +

PPFF, Venmo Gift, Zelle