Selling my holsters, sold the gun so I no longer need the holsters.

Factory Barrett MRAD .300 NM barrel with bolt head no magazine. 250 rounds fired shoots great, loves 230 Bergers with N565.

Factory Barrett MRAD 6.5 CM barrel with bolt head no magazine. 300 rounds fired factory loads only.

6.5 CM $875 shipped
.300 NM $825 shipped

The action is a Savage 110
The stock is a Bell and Carlson
I added AICS bottom metal and Mag
The barrel is a FAXON M24 Contour Blank 27" 1:10 Twist

First I zeroed the barrel in the lathe and cut the receiver threads, then chambered carefully. I then cut the muzzle for a brake 5/8 24. I had to seriously inlet the stock to free float this barrel.

Out at the range today, the rifle is shooting the federal fusion tipped 180gr over 91.5gr of N570 into a single hole, 7 shot group all can covered with a dime. Seems this one is good to go now. Very low recoil, like shooting a 22 250.

My data shows 91.5gr (Max safe published load) of N570 is around 64k pressure but I see NO SIGNS, running a 180gr pill at 3300fps should be serious medicine for the dear this year

Need a fde or tano mpvo no less than 10x on the top end. Let me know what you have available.

Selling two APA Fat Bastard Gen 3 muzzle brakes. They are the same model, black nitride, 5/8-24 threads with .30 cal diameter bore. Both are in excellent condition and no damage. Might not be completely clean of carbon, but easily taken care of. Price is $120 (each) shipped to you in the lower 48.

Wondering if running my brake had an effect on accuracy and also whether using a neck expander or not effected accuracy. My data set is very small, I understand that, but was wondering what the results might indicate... Results are 5 shots each at 100 yards.
Equipment:
Tac Ops XRAY-51 .308, ZCO 5-27 scope, Alpha brass, Berger 115 flat base target bullet, CCI small rifle primer, VV N-135, 44.0gr. 2.190 ogive, @3025 fps. SAC modular sizing die, 334 bushing, 80 degrees, overcast, no wind.
Results:
Left side is no neck expander with 4 port Hawkins brake and with no brake.
Right side is using a 306 neck expander with the same brake and then with no brake.....

Assuming all things being equal... Not using the neck expander with No Brake appears to be the way to go. At least with my equipment. 5 shots measuring 0.097".
Tiny data set, but interesting to me.

RCBS Chargemaster 98923
Like new Chargemaster in the original box with instruction manual. Has all the parts and includes a small straw outlet (brass) AND an Area 419 tray and cup. Powder cylinder still has the factory wrap on it.
$325 shipped to lower 48

Ohaus DU-O-Measure powder measure
Good condition Ohaus thrower. Will throw large (rifle) and pistol(small) charges by just rotating the drum. Includes a set of instructions from the internet.
$80 shipped to lower 48

RCBS Uniflow. Not sure what version. Includes both large and small drums and parts to throw rifle and pistol load. All parts in the photo only. Nothing missing that I am aware of. Instructions available from RCBS website.
$80 shipped to lower 48.

RCBS Little Dandy Powder Measure w/ No 13 rotor (new).
$40 Shipped to lower 48.

Only what is shown in the photos are included.
PPFF is the only EPayment or USPS MO.
NO Trades needed.
PM me if you are interested. I will not contact you from a post.

Selling a new unused desert tech 338 cal QD muzzle brake threaded 3/4x24. Took it off my SRS 338 lapua barrel. Would make a great 338 brake for any barrel. $100 shipped

Recently built myself a 6 dasher hunting rifle and I've got an odd cold bore flier. It always starts a half inch high for at least the first shot, sometimes the first two.

the action was already bedded from long ago but I had to redo the area around the recoil lug when I rebarreled it. Right now the lug is surrounded with bedding and a short portion about ¾" ahead of the lug.

My question is, should I relieve everything in front of and below the lug ?

I've done two other rifles the way I did this one and they shot well. No cold bore shift or anything put of the norm. Just this one giving me fits. Could be the cheap outlier barrel, but the barrel will group. Just dealing with this coldbore issue right now.

Sold a Lyman Case Trim Express. Asking $100 shipped. Includes pilots and power supply.

For sale is my lightly used Garmin Xero C1 Pro Chronograph. I used this device about 5-6 times.
I was issued another Xero at work, and so am selling this redundant one.

Includes box, device, tripod, USB-C cable.

Looking for $475 Shipped.

Arc m10 scope rings 1 inch tube 36 height
$100

$90.00 shipped lower 48
Zelle or check only


Nice condition, just cleaning out

Arc m10 scope rings 34mm tube 36 height
$100

Looking for a Spuhr mount, SP-3001, 30mm 1.18”.
Please pm with photos and asking price.

Will only deal with established members having positive feedback and full account status.

Customize your monocular with every option on the market from the largest inventory with NO LEAD TIME! Pictures and specs of every tube. Best prices guaranteed.

PVS-14 / AB Night Vision RVM-14 / Nocturn Industries Tanto (Black, FDE and ODG)

Call anytime if you have any questions
713-568-6823

Customize your night vision binocular setup with highly discounted accessories for a complete turnkey package with NO LEAD time!

12 Binocular Options + 3 Optic Options + 100s of L3Harris Technologies, Elbit Systems and Photonis Tube Options (specs and picture posted!) means 1000s of Possible Night Vision Builds.

AB Night Vision RNVG (Black, FDE and OD Green)
AB Night Vision RNVG - Articulating (Black and FDE)
AB Night Vision RPNVG - Panning
ACTinBlack DTNVS
Act in Black DTNVS Manual Gain
Low Light Innovations MH-1
Nocturn Industries Katana (Black, FDE and OD Green)
Nocturn Industries Katana Rugged (Black, FDE and OD Green)
Nocturn Industries Manticore Rugged (Black, FDE and OD Green)
Nocturn Industries Daisho (Black, FDE and OD Green)
Dual PVS-14 on Noisefighters M1 Panobridge
Dual Nocturn Industries Tantos on Noisefighter M1 Panobridge (Black, FDE and OD Green)

New in box never fired, LRP S3 4-25x50 in Mil.

Asking $1600 shipping included.

WTS Razor Gen 3 - EBR-7D - MRAD - used but like new condition (see photos)

SOLD

5x5 precision MDT elite grip

$45

Redding premier 3 die set, $sold shipped

Make an offer, trades welcome

Title says it all, I would like to buy a TRIARC 15 Inch M-LOK Attached ARCA Rail.

Selling my desert tech SRS A2 chassis with monopod. Never been shot, excellent condition. Can be whatever caliber you want, just need a bolt, barrel, and mag. The A2 is adaptable to longer handguards and top picatinny rails. The trigger is far better than normal and breaks at 1lb 12oz. I’ll throw in an atlas cal bipod with it. $2850 shipped for the chassis and bipod

Sig SAUER cross rifle chambered in 6.5 Creedmoor. 400 rounds on the barrel. 18” barrel. $1200

Trades I’m interested in
Remington 700 SA chassis either the
MDT HNT 26 w/ folding stock or
XLR Element magnesium chassis w/ folding stock