Recent content by Numn

Re: Fully Diss. Assy. 308 Suppressor??? Another Shark recomendation...great product combined with great customer service. The most versitile can I own due to integrated thread adapters. Huge advantage of the modular design is that in the event of a baffle strike if the outer tube is not...

Re: DOA Tactical Shooting Benches They have supplied benches at SHOT Media Day for the past couple of years...quality bench. Well made, sturdy top that's relatively light, takes about a minutes to setup and is simple to adjust for different users. The top and seat easily swivel which is...

Re: Benchmade Auto Knives Another +1 for Blade HQ. I'm fortunate that they are only about an hour from me so I shop there in person. Knowledgeable staff and a lot of Benchmade in stock.

Re: TRG-22 or AIAE It really depends on which fits you best...they are significantly different. Both good but regarding ergos are very different. Personally I prefer the AI ergos; however, I like the TRG trigger better.

Re: S&B 5-25 New MTC locking turrets issue/questio I received my locking turret S&B about two weeks ago and initial adjustment was simple. Between a 30 moa rail and 18 moa mount the scope was within 0.3 mil out of the box so initial adjustment was minimal. I engaged the turret lock ring to...

Re: Velocity vs Barrel length on TRG <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: jbell</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Numn</div><div class="ubbcode-body">I just so happen to have side...

Re: Velocity vs Barrel length on TRG I just so happen to have side by side velocity data (10-shot strings) for both 20" and 26" TRG's with the following load: 175 SMK 2.865 OAL (.020 jump) 44.4 gr Varget Lapua Case GM210M Primer 78 degrees 20": AVG 2579 fps, SD 10.7 26": AVG 2656 fps, SD 11.1

Re: Maximun Cheek spacer height for TRG TRG-42 in 338LM with 10mm spacer...bolt can not be removed, but as stated earlier, it's easily resolved in about 10 seconds with an allen wrench.

Re: Ballistic FTE and DA problem I also could not get DA to work on my device...change the settings and reboot...no change. I finally deleted Ballistic FTE and re-installed. After installation I went straight to settings, changed to DA then rebooted. It's a miracle, DA now works. Don't...

Re: Apex kit <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: shoot4fun</div><div class="ubbcode-body">I have a M&P45 coming soon. I think an Apex ket is in my future. I just got a M&P40 Pro 5" and the factory trigger on it is better than any M&P I've had to date...

Re: TRG suppessor w/18x1 or use adapter +1 David builds a great can and with the added versatility of a very clean thread adapter it's a no brainer.

Re: I.O.T.A (Indoor Optical Training Aid) Received mine yesterday. What a great training tool, works as advertised. Initially I tested on a NF F1 and combination will focus max power at about 11 ft. Thank you Chuck.

Re: Form 4 wait time Looks like mine ran similar to others. Shark can on a Form 4: Check mailed Aug 19th Pending Sept 19th Approved Dec 7th

Re: Atlas Bipod spigot for Sako?? I'm sure Kasey will chime in here but last time I emailed him was around mid October and the TRG spigots were at least a couple months out. So, no you didn't miss them.

Re: Large data deviation with Ballistic FTE I have found Ballistic FTE to be very accurate, especially when using the JBM computer. If your BC and MV were input correctly I would double check the zero and current atmosphere settings. Occasionally I have had strange results with the 'Pressure...