Search results

Goodshooting.com good personal service if necessary

I shoot .260 Rem and use the Lapua Scenar 139. Mr Litz had listed G7 at 0.301. My Model 12 LRP Savage 26 inch barrel found actual G7 BC of 0.291. I shoot out to 800 yards and at 600 regularly with the 0.291 G7 and StrelokPro is on the money at 600 yards and average 2815 fps MV. Using standard...

Harbor Freight. Had to get coupling off ebay. Most painless step in my preparation.

I have been using Frankford Arsenal Platinum handtool. It is adjustable and is very consistent with what I consider to be good feedback on primer insertion. 50 - 100 primers no problem for the included tray. Would definitely hold more but just never have done more than 100...

This is from Redding site copy/paste; https://www.redding-reloading.com/online-catalog/118-type-s-bushing-dies Looking at their table 300 Win Mag is only listed under Category I. Various combinations of Type S full dies, Match sets, Competition sets etc... You would also need to know...

Loaded Accubond 150 gr with .308 Ruger Hawkeye, 22 inch, 1:10 Federal Brass 3TF Trim 2.008 Shoulder bumped back to 1.620 (.002) Neck Tension .002 COAL 2.800 H4895 42.5 gr (43.0 showed some flattening primer, no hard bolt lift, used final 42.5 gr) Chrono Avg 2710 fps, Spread 22, SD 9, 10 shot...

2nd the 155 Sierra TMK however my loads out of 24” barrel for 600 yd BR.

"At The Lands" yes but different application in your AR10 magazine situation for sure. Just basically saw 155 gr. Sierra TMK and responded without realizing totally different shooting application.

Model 10 FCP HS Precision .308, 24 inch : 155 gr. Sierra TMK over H4895 in Lapua brass. Originally shot at 0.010 jump. After about 1000 rounds chased lands and found ATL to be the best in my rifle. I have about 2200 down barrel now.

Been shooting with custom earplugs for years. Latest set I sent in earmold in myself (wife helped make them) and company did really good final product. https://www.earplugstore.com/westone-defendear-industrial-max.html

More than likely a normal bore guide would allow pass through. However I would want to help protect the camera end which includes the lamp from touching anything other than the Delrin bore guide which I think is about $20 if I remember correctly.

I use Lyman borescope. Throat area, lands and any possible carbon ring would be very obvious. I have used it for about a year now and very satisfied for checking especially to verify cleaning method before/after. Based on your primary purpose I would recommend without hesitation. I do use...

155 gr. Sierra TMK loaded with H4895 ATL in Lapua brass with GM210M primer @ 2923 fps. Savage Model 10 HB, 24" barrel.

Same site as link above for ej-123 the fx-120i is 500 alone and then you could add the auto throw or trickler later. They also have the bundled deal. My ej-123 does not drift off zero once warmed and I load to the kernel if I want in my H4350 (260 Rem) and H4895 (.308 Win). I weigh using the...

A&D EJ-123 reads to 0.02 grains, 0.001 grams, holds zero for days on end. It doesn't like your AC draft. Regularly listed for approximately 500 but the link takes to site from Canada for 300 American. Use mine with powder throw about 0.2 to 0.3 grains under and Dandy trickler. Not quite...

With my factory Savage 26" LRP I too thought 142 SMK would be the end all. Using H4350 (have not used Varget) I never could find any reasonable grouping with the 142 SMK at different nodes and bullet seating. I tried 140's and Berger Hybrid 140 all to the same results. A buddy suggested I try...

Savage 1:10 twist 24" barrel Lapua GM210M Primer H4895 44.8 gr Chrono 2923 f/s Sierra 155 TMK set ATL

These look really good. Thanks for sharing your hard work.

Neck turning your brass is not necessary to use the Redding FL Type-S bushing die. I can chronograph single digit SD's without ever neck turning. I am not aware of the reloader who turns necks with factory chambers but my wingspan of shooting knowledge is local. Custom chambers with "close"...

Loaded Lapua .308 brass with Sierra TMK 155 final assembly measured at 0.337. I have used a .335 bushing for 0.002 neck tension shooting in my Model 10 FCP HS Precision Savage approximately 2000 rounds. I don't use the expander ball but use the provided decapping pin retainer. I use a mandrel...