• Watch Out for Scammers!

    We've now added a color code for all accounts. Orange accounts are new members, Blue are full members, and Green are Supporters. If you get a message about a sale from an orange account, make sure you pay attention before sending any money!

Search results

Search the forum Search Articles
  1. 1

    reloading question

    Re: reloading question The sharpie will,do the trick. Should always trim for AR's. The decapping pin should not extend more than 3/8" beyond bottom of case.
  2. 1

    Rear lugged vs. non M1A?

    Re: Rear lugged vs. non M1A? Thanks for the update. Mine shoots 9,10 x ring with regular 147g. nothing special hand loads. I'm very happy.
  3. 1

    Are any AR-15 parts made in China?

    Re: Are any AR-15 parts made in China? China manufactured AR-15 parts, definitely.
  4. 1

    My M1A

    Re: My M1A Looks really good but I bet offhand is a handfull.
  5. 1

    Hornady Lock-N-Load bushing conversion

    Re: Hornady Lock-N-Load bushing conversion After adjustment LnL bushings seems to hold well in the progressive press as well as a single stage conversion.
  6. 1

    Federal Gold match in M1a

    Re: Federal Gold match in M1a I picked up on that Garand comment, can you help with how hot is hot? Can you recommended Garand specific reloading data sites of info?
  7. 1

    AR bolt pin ?

    Re: AR bolt pin ? It should not stick out on either side beyond the curve of the bolt. From time to time these seem to hang and if you pound, you bend and have to replace.
  8. 1

    Rear lugged vs. non M1A?

    Re: Rear lugged vs. non M1A? I am guessing you leave the receiver assembly in the stock and don't remove it ever, unless you have a problem?
  9. 1

    I need to know by tomorrow about a national match

    Re: I need to know by tomorrow about a national match Installed the Sadlak Airborne last night and it's a Perfect fit. Will give it a run through this weekend to determine how it holds up.
  10. 1

    Beretta BM-59

    Re: Beretta BM-59 Hum, that might be a fun project. What are the SARCO part kits going for?
  11. 1

    Beretta BM-59

    Re: Beretta BM-59 Why do I like things now, I didn't care about 25 years ago. These were around and available..
  12. 1

    I need to know by tomorrow about a national match

    Re: I need to know by tomorrow about a national match I just picked up a Sadlak Airborne, looks like you recommend it. Better in person than in pictures.
  13. 1

    Leave Rifle Cocked Or Not?

    Re: Leave Rifle Cocked Or Not? Same here, all calibers. Most admiring anything I have its finger off the trigger and definitely no cycling.
  14. 1

    Rear lugged vs. non M1A?

    Re: Rear lugged vs. non M1A? Can you describe skim bedding.. It that related to filling gaps created over time?
  15. 1

    Rear lugged vs. non M1A?

    Re: Rear lugged vs. non M1A? Battle rifle for now. Thank you for the help..
  16. 1

    Rear lugged vs. non M1A?

    Rear lugged vs. non M1A? Tried to search this subject, what's the benefit, what's the difference in appearance?
  17. 1

    Armalite Bolt carrier starting to split.

    Re: Armalite Bolt carrier starting to split. I will try to post a pic.
  18. 1

    Snake in the grass.. the poor man's version

    Re: Snake in the grass.. the poor man's version What mix ratio, paint to catalyst to any reducer? You need enough catalyst for it to set up and harden.
  19. 1

    Why was the bolt hard to close on 400 rounds?

    Re: Why was the bolt hard to close on 400 rounds? What about trimming the brass?
  20. 1

    Hornady Lock-N-Load Auto Charge.

    Re: Hornady Lock-N-Load Auto Charge. How do you know what actual weight you are receiving without checking it with another source?
Top Bottom
Back