Search results

I need to make a piece of bar stock into an octagon basiclly. I have always programmed stuff like this by laying out the toolpath in mastercam and then add the 4th axis indexing by hand in the post process editor. I have had enough with the work around and I can't figure out how to do it in...

Getting ready to pull the trigger on one of these stocks for my tikka. Anybody got one that I can hold and see in person before I drop dime. I am located in midland. Thanks

I have a great employment opportunity. It is in the firearm industry and money is a bump over my current dead end non firearm industry position. The down side is I will be driving and be on the road approx 3 nights a week. I was not in the military and have never had a job that required this...

I have a 308 redding s type bushing die. I also bought a 290 ti coated bushing for it so I can use it for my 260. I run 7-08 win brass in and it comes out .286 od on the neck. With the ID being .257". I measured my bushing and it is .286" anybody else ever get undersized bushings? Also since...

I just started shooting prone, before this it has always been bench work. First time to 200 prone and these are my 2 problems. My setup is trg 22 308 20", vortex razor, atlas bipod, reloads that shoot 1/2 moa. 1) After the shot the gun jumps left. I continued to shift my body left to the...

I have a buddy that just bought a TL1 and is looking for chuck options. I know there are a few guys on here running these. What is the verdict? I am assuming the TBAS only adjust in the A and B axis while the X and Y axis you still use the chuck. Is this correct? Also how is the chuck...

Anybody have a source on a set on long T3 action screws? I put a trg trigger in my T3 and the trigger rubbed on the trigger guard. Made a couple washers and put them between the stock and trigger guard and trigger works great. Now I only have a turn and a half on my action screws. Gun is 223 so...

Anybody use one of these? I want to put my atlas on my t3 varmint. Good, bad? Any alternatives?

I tore my dies apart today to clean. My expander balls all have brass ribs on them. I clean them when I get them and lightly coat with imperial wax. Why is the brass still sticking? Scrubbed with OOOO steel wool and it knocked most off but it will still catch your thumb nail. Dies are redding...

I have access to shot peening media from work. Anybody ever tumble with this? Seems like it would not leave the residue dust the "organic" media leaves. Good idea or bad?

Not sure if this should go here or in the suppressors section but since we are talking about threading the gun lets try here. I have two trg 22s. One in factory 20" 308 threaded 18x1mm. The other is going to be rebarreled in 260 once I get my barrel back from rock. I don't know what I should...

I have a 08 GMC sierra w/ 4.8L. Orginal battery. Truck starts fine even in cold weather but radio clock resets every morning. Voltage at battery when runing is 14.65, off after running 12.65 and after sitting all night with temps in the teens before starting 11.60. Any idea? Not a huge...

Opening morning on public land, got there 2 hours early to stake my claim, didn't have any problems though. 20 minutes into legal light a yearling come running out at 20 yds, followed by a doe. The doe turns and runs right at the me and the stump I was sitting on and misses me by 3 yds!! This...

I am going to make me a 10/22 w/ pic rail and a couple other adjustments. I only have 1 problem (well at least that we need to discuss here.) How do you drill the hole for the guide rod at the rear of the receiver? Could drill it through from the backside and then plug it but that would be...

I am looking for the inlet pattern for seekins aics 700 sa bottom metal. I have seen the pattern on here before but I cant find in. Anybody know where to get it?

Anybody have any experience? I saw something scary today from someone using them. load was 4227 w/53 gr bt.

I am looking to paint one of my trgs in 4 color Flecturn. I want to use black, dark and light grey and white. Has any body done anything like these color before? Want to see if I like it before I take the leap.

Since the ax 338 is now in production is the aw 338 still being produced? Saw a post approx a year ago from tom Irwin that sounds like yes but had plans to phase them out without any date listed. Thanks

Looking at a 8400 advanced tactical. How is the quality of these? Don't see too may around. Cdi makes bottom metal I think for them. Lately I have seen several issues with kimber handguns that is quite disheartening but wondering if their rifles are suffering the same fate? Thanks.

Getting ready to paint my trg with duracoat. Going to try 4 color flec. What prep should be done on the stock as far as adding some tooth for the paint? 400 grit sand paper? Courses, finer? Will acetone harm the stock as a degreaser? I like the factory parkerized finish, but can I degrease...