338

Anyone have any good loads for RL25 and a 250 grn Scenar. I just got 2 lbs of it so I want to try it out

can a remy or savage long action be swapped over to a 338 lapua or does that take a special length action

Alright I am after a safety check. I plan on loading some solids in my 338 LM. I know that with solids you can basically get more with less, so to speak. So if I take load data for a bullet of similar weight and conventional construct then reduce the load by 10% will I be safe or am I off base?

Any one have any data on this cal ? Later Chris

Just looking for a little feedback on the N-170 powder for the .338LM and the 300gr SMK. I currently use RL-22 but the SD is around 15. Of the different VV powders I have tried they have been very consistent.

Could anyone recomend a good powder for 338 Lapua with 250 gn bullets. Maybe some load data too. Thanks

Can anyone tell me what size shell holder I need for the "new" .338 Norma mag case? I tried a #14 RCBS which I use on my .338 Lapua and it will not work. I called Redding and they said to use #14 and it doesn't work! Also called Sinclair they don't know either. Tom Sarver

Any suppliers have .338 Lapua 300gr bullets in stock?

Hey, I'm a brand newbie on here, so please be kind if my questions are stupid, or if they have been answered a million times already. I'm in my late forties and have been shooting/reloading since I was about 14. The biggest rifle I have owned is a 270 Win, but I have fired 99% of my rounds...

Got to handle my new 338 Lapua built by TMR/ JLR AKA R Bros Rifles. Very very nice! Pictures don't do it Justice. Phoenix action, Seekins bottom metal, mag, rail and lug. Jewell trigger, Manners T2A stock, Rock M-24 fluted 9.3 twist, Defensive Edge brake, desert digital camo. Enjoy A little...

I am building a 338 lapua on a AICS and Im new to the laupua, does anyone have any suggestions? Anything helps

Curious as to what is different between the .338WM and the .338 Lapua (if any). Looking at buying a .338 action for my next project rifle and i have found Howa to make .338WM IS this weatherby or winchester magnum? Are the cases different to the Lapua? any info appreciated.

I have a 9.5 twist krieger barrel on a surgeon xl action. I found a load that will shoot the 300 grainers pretty well it's imr 4350 but the velocity is only 2650 fps. I was wondering if any one else has any loads that are faster than this that will shoot 1/2 moa or better. Trying to find a load...

I was reading a post on longrangehunting and someone mentioned a 307gr. amax. Has anyone heard of this before?

Performing some tests on Noel's .338 Bullets: Finally got to the Range a week ago. L to R: 250 Scenar, 300 Scenar, 253 gr, 256 gr, 265 gr, 318 gr. ZA. Length(in calibers): 250 Scenar: 4.63 Cal 300 Scenar: 5.14 Cal 253 ZA: 5.4 Cal 256 ZA: 5.6 Cal 265 ZA: 5.9 Cal 318 ZA: 7.0 Cal Testing was...

I would like to get a ballistic compairison on the 338 edge and the lapua mag

Well it's finally done and as far as I know it's the first T-Wolf to have the honor of sitting in a Sentinel stock. .338 Lapua PGW Timberwolf Action KMW Sentinel Stock 28" Krieger 1-10 twist FTE Brake 40X Trigger Nightforce 5.5-22x56 NPR-1 and rings Have to wait for days off to give her a...

I am thinking about building the 338 Edge but I have a few question before I start. I will either be using a Savage or Remington 700 action for the project. My question is..Will the standard long action magazine be long enough to make this gun a repeater or will I have to make some mods to...

If you were going to build a 1 mile rifle is there an advantage of going with the Lapua mag over the Ultra mag? This rifle is for a as of now, non-hand loader. Aside from the fact that for that distance hand loading is a must, what would be the other advantages???

I just ordered my GAP .338 LM. Even though it will be 6-7 months before she's ready, I'm looking for reloading data for it. Where should I start? What is your opinion on bullet types/sizes? The barrel twist is 1-10. All suggestions would be appreciated.