Brand New! Taken out of box for pictures. ARC Coup De Grace. SA , Right hand , .473" bolt face , Hourglass , 20 MOA , Red , Not Fluted , Pivoting.

$1,075 to your FFL from my FFL. $1,000 for face to face sale at my FFL or yours in the Boise, Idaho area.

Venmo , Zelle , USPS Money order or Paypal F&F

Has gone missing from Union Pacific...

• Remington 700 RR Prefix Action
• Blueprinted by LRI
• LRI Tactical Recoil Lug
• Base Screw Holes Opened to 8-40 by LRI
• Straight Fluted Bolt by LRI
• Bolt Handle Threaded by LRI
• Nightforce 20 MOA Scope Base
• Badger Ordnance Tactical Bolt Knob
• Proof 22" 8 Twist Barrel Chambered by LRI - 7 SAUM
• 5/8x24 Muzzle Thread w/ Thread Protector
• Metal Finish: Cerakote Elite Blackout
• Manners EH1A w/ Mini Chassis
  • Metallic Moola Pattern I think
  • Picatinny Rail Up Front
  • Another anchor point mid forearm (10-32) for mounting an arca rail. Works well with 8" Area419
  • Two flush cups on left side
• PTG Bottom Metal
• 10 Round WSM/SAUM Magazine

0 rounds down the tube. Too many hunting rifles. Can only claim so many are for my kids.. About ~$3700 to put it together.

$2750 Shipped Conus

Stainless TIKKA T3 w/ Picatinny Rail
Mountain Tactical Bolt Release (allows more bolt travel for longer rounds)
Yo Dave Trigger Spring
Straight Bolt Handle and LRI Bolt Knob
Carbone Six 9 Twist 18" barrel Threaded 5/8x24
.308 Winchester
Metal Finish: Cerakote Elite Tactical Blackout
Tikka Tactical Adjustable Stock
Mountain Tactical Aluminum Trigger Guard/DBM
3 Round Tikka Magazine

Approximately 125 Rounds through the rifle. Legitimate 1/2" MOA or less gun. Shot factory Hornady 178 grain ammo in one ragged hole as well as handloads, both jacketed and solids.

$1925 Shipped CONUS

He was only 58....no cause of death listed

These are a nice piece of gear to protect your kit!

Schmidt & Bender 5-25x56 PM II LP P4 fine reticle Mil CW DT/ST

I used this routinely when I was shooting PRS matches. Getting old now and into F class only. This has wear marks on the turrets but functions perfectly. It's been a safe queen for the last few years. Took it out and noticed a focus problem. Sent it in for repair and it had a new objective assembly put in. All checked out by S&B service center.

Includes Seekins low rings.

$2000 shipped

Login to view embedded media
Target is also pedal to the metal with grooming children.

It's only getting worse and I don't think it will play out like we hope.

I have a LNIB Bushnell XRS3 with G4P reticle. I bought it new from another member here. I mounted it but never took it out. Glass is good and has no issues. Asking $1100 shipped.

I also have a Bushnell Match Pro ED. This one was going to be used with a CZ 457 for production class but decided to go straight to open class so I don't need to stay under a certain budget for the scope. I purchased it this month when they were back in stock briefly. I figured someone might want it before I try to return it to Bushnell. It was never mounted and only taken out of the box to inspect it. SOLD

Walsh custom defense 120 round br/dasher/gt ammo holder retails 140

75 shipped conus

I have a .30 cal barrel that I bought about 10 years ago off another shooting website . I was told it's a Krieger barrel but there's no Krieger stamp on it.
One friend said it might be before they started putting their name on it.
Do you guys have any thoughts on who made the barrel? Any info would be appreciated.
Specs:
29" long
28 1/2" to the cut at the muzzle end
2 1/4" shank
1.270" at the breech
1.250" past the shank
.880" at the muzzle

298 308
5R
11
19590
C30

Someone shared: NAACP Arlington: tree equity is 'a matter of life and death'
https://wjla.com/news/local/naacp-a...rist-of-latter-day-saints-ecoaction-arlington

Rem 700 SA Right Hand MPA matrix polished finish, comes with enhanced night vision rail, along with the standard night, vision rail, the competition side rail kit, interior and external forend weights, dope card holder to round holder the extra grip, the extra thumb shelves and finger shelf along with the rear weight as well.

That is a solution for a problem that does not exist........... But it is perfect for It’s for call of duty LARPer


It also requires you to hold the rifle like a retard..........


If it’s Alexa enabled I’m in.......
"Alexa zoom to 6x" ..........










Login to view embedded media

I have about 1500 rounds of 6mm creedmoor brass, primarily Hornady. It is all once fired and boxed. Would anyone be interested in purchasing all of this brass for $150 shipped.

Air Force Major Brian Shul, Ret. died suddenly last night of a heart attack in Reno, Nevada he was 75. In 1973 toward the end of the Vietnam War, he was in a near-tragic plane crash that burnt most of his body. He courageously fought back and was able to fly the SR 71. He is well known for his story “speed check” prayers to his family. and to his many friends.

God speed.

So I have over 400 rounds on this barrel and I cannot find a load for it. Gave up on the 75 ELD and still not having any luck with Berger 85.5. I’ve found my velocity node and carefully weighed each load of varget to the kernel. I tested a bunch with the base of the bearing surface at the neck shoulder junction and had no luck. So today I tried Berger’s suggestion intervals and groups still look like shit. Pics below of .020, .030, .045, and .060 off the lands.

This barrel has a .100 freebore and at .020 off the bullet is barely in the case. Never had much trouble before finding a load but this thing is really frustrating me. I don’t know where to go next.

Remington s/a or clone, scorched earth, complete with steel Arca weights. NO clutch. Like new condition. I’ll get pics up tomorrow. There is a dab of bedding in the lug area only for the impact action. The bedding in the lug has been removed by my gunsmith.
$1400 shipped- No trades.

I am running the following:

• Aero Precision Upper/Lower
• Geisselle two stage trigger
• Omega Suppressor
• Hand loads 168gr Nosler Ballistic Tip
• 18" Proof Research CF Barrel
• JP Enterprise Silent Capture H2 for AR10
• Just installed an Superlative adjustable Gas Block that allows for gas bleed off

I was getting double taps often and double feed issues, changed out to a adjustable gas block, those are gone but still get random double taps.

Do I keep going on the bleed off clicks and hope it cures the double tap? Or, am I chasing a ghost??? Any thoughts???

Thanks much!

Is there anyone out there preheating barrels to combat cold bore flyers? I'm just curious. It sounds like more trouble than it's worth given how hot it must have to get.

Long time lurker, first time poster here. I'm absolutely stoked to share with you all that I've just managed to pick up an Accuracy International AE MK III (pristine condition, basically new), chambered in 260 Remington, all for a cool $4500. This is my first venture into the world of long range bolt action shooting, although I do have a CZ457 that's also en route to me (I guess it's just my lucky season!)

I'm quite familiar with short to medium range shooting, but I'm still getting my feet wet with long range precision. Therefore, I am humbly reaching out to this amazing community for advice. I have to admit, having such a sophisticated tool in my hands is a bit daunting, but also extremely exciting.

1. Preparation: What should be my first steps in terms of preparing the rifle for use? Any specific break-in process I should follow, or other maintenance/care tips specific to this model?
2. Optics: I haven't decided on optics yet, and could really use your input here. I'm aware it's a highly personal choice and often comes down to budget, but I'd appreciate any recommendations you might have. My budget is reasonably flexible, and I want something that will do justice to the capabilities of this rifle. I'd love to hear both your high-end and budget-friendly options.
3. Ammunition: I know that 260 Remington has a good reputation for long-range accuracy, but any particular brands, grain weight, or bullet type you prefer?
4. Accessories: Are there any essential accessories I should consider? Bipods, muzzle brakes, anything else?
5. Training/Practice: Any drills, training routines, or resources you'd recommend for a newcomer to long range shooting? I want to make sure I'm honing my skills in the right way.

I'm excited to embark on this journey with such a renowned piece of kit, and I'm eager to learn from all of you. Thanks in advance for your time and suggestions!

Have a sr25 ecc m110k1 under 200 Rounds fired
$12500 or trade to other sr25
6062806163 for more pics

Yesterday I shot a match in the rain. It was a wet and muddy soupy mess. When I stripped the gun afterwards I went to clean my lenses which were also a mess. The ocular lens came out fine, but my objective lens is ruined I think? It looks like I wore off some of the coating on the lens.

The scope is a Bushnell XRS3. I used the same SOP I use to clean all my optics: A lens bulb blower, a lens brush, and followed it with a spray solution from Vortex with a microfiber rag also made by Vortex.

Picture below shows what I’m left with now. I don’t want to play with it anymore and plan to call Bushnell tomorrow and see what they say.