Selling a lightly used NF 7-35 F1 mil xt. Scopes in perfect condition I think I had a couple rounds fired with this mounted. Mount is a spuhr qdp-4602 6mil/20moa. Been sitting inside the safe looking for a new home
3000 shipped insured scope
3350 shipped insured scope with mount

So @WillHugh and I sent out 223AI barreled actions to get turned down to 18" and profiled for OCM5/AEM5 suppressors. The goal was to build intermediate range, low recoil, bolt guns that bridged the gap between Mk12 gas guns and 6.5CM capabilities. If velocities of 2850fps with 80gr ELDs are achieved, the guns are transonic to 750-800 yards and supersonic past 1000.

The 223AI of mine was cut down from 24" to 18". I was running 25.6gr of Varget in Winchester brass behind Hornady 80gr ELDM and 80gr Amax. Velocity prior to the cut was 2950fps and it shot clovers at 100 yards.

Got the barreled actions back yesterday although my Manners TF3A is still with the gunsmith being inleted for a Badger EFR, so I put it in a spare Manners EH2. I did learn that I needed to dremel out the front of the Accurate metal mags to get clearance for the 80gr Amax bullets whereas the plastic MDTs have always had room.

The range trips today was promising! The rifle shot around 1/2 MOA, with 2 of the 5-shot groups a clover leaf around under .4" at 100 yards. Velocity averaged 2803fps at 87'F. The surprise for me was how high the SD was at 17. The translates to an ES of 57fps, or about 0.5 mils at 1000 yards. At 500 yards, this load is about 2.7mils of elevation and about 9.7 mils at 1000 yards.

Since I have about 60 rounds left, I plan to shoot the rest and then try some StaBall Match was had great results in my Mk12 and my Dad's .223 bolt gun. I am hoping the SD can tighten up to high single digits with velocity in the high 2800s.

Will has his rifle setup in a sweet Manners T5 and unlike me, his OCM5 isn't in NFA jail, so the rifle looks amazing.

These promise to be relatively lightweight and fun guns, looking forward to stretching them over the summer and during some night shoots.

-Zermatt TL3 AW cut action, accepts AICS mags as well. (McMillan tan H-Series Cerakote done by a certified applicator)
-Proof Research carbon fiber 6.5 Creedmoor 22" barrel (sendero, 1:8 twist) 120 rounds on it, came direct from Proof. 5/8x24 threads @ muzzle.
-Hawkins Precision M5 dbm (McMillan tan Cerakote)

Would like to sell the barreled action, a self timing brake, and the bottom metal (without trigger) for 2150.

Thanks for looking!

Fuck the fourth amendment and all private property rights !!!!

Login to view embedded media
I love the part where the rest of the thugs stop the bad apple from stealing private property and assaulting a lady with no warrant or evidence, o wait that did t happen cause orders and pension and what ever war on drugs shit they are peddling these days .

Login to view embedded media
I’ve never seen Warren Buffet out and out lie before and he’s not very good at it……..

Guy sent me this message on an old WTB add I had up. Buyers beware. Joined 27 min before sending me this message.

@killopp098877

Hello, I have 1 brand new Foundation Centurions Black inlet for Impact SA 737. I have never even put bottom metal in them.

Each stock will come with

1 lightly used Hawkins bottom metal M5 DBM SA
1 lightly used Foundation Full length ARCA rail
1 new brass weight set.

Price includes shipping Via FedEx ground.

Both Sold

No trades offers please.

Magnetospeed V3
Latest firmware

$275tyd

Marlin 1895 GS in 45/70. JM stamped, unfired. At the time of puchase in 2002, I had another 1895 that I shot and didn't really enjoy, so this one got no love. Fast forward almost 20 years with a renewed interest, I took it out of the box with the intention of using it, but never got past working the lever quite a bit. Apparently, another rifle got jealous because I sat it back in gen pop and found out it got in a fight with another rifle. It came out on the losing end with a few bumps and scratches on the stock, the other rifle unscathed. So much for sheltered kids growing up to be tough. Anyway, it now thinks it knows everything, is grown up, and wants to leave home, so here we are. $1300 shipped.

Happy with 107s so these bad boys can go. 1 box LIMIT. $319 shipped flat rate; insurance optional. Firm, no trades. Paypal ff or Zelle.

First Thing: Pentagon leaks linked to young gun enthusiast ...​

The Guardian
https://www.theguardian.com › us-news › apr › first-t...



6 minutes ago — The man responsible for the leak of hundreds of classified Pentagon documents is reported to be a young, racist gun enthusiast who worked on a ...

Hello,

I have 2 LR .308's I built with Aero Precision lowers and uppers.
The 18" has a custom Bartlein barrel and the 16" has a Wilson combat Recon barrel.

No matter what the configuration, the JP bcg ALWAYS jams.

Conversely, Whenever I use my Aero Precision bcg, no matter what the spring/ weight configuration, it runs flawlessly.
- both rifles run FLAWLESSLY with the Aero Precision bcg in any spring/ gas/ buffer/ magazine/ ammo configuration.

For example, if I put a regular buffer spring with a 3.4 oz buffer weight in both rifles, both rifles run flawlessly with the Aero Precision bolt... however, both rifles will jam with the JP enterprises fmos bcg (empty casing above new round that won't feed).

If I put Springco Orange buffer spring in both rifles with 5.1 buffer weight, again, the Aero Precision bcg runs flawlessly, but when I put the JP enterprises fmos bcg in, they both fail to cycle.
It's not a gas issue.
It's not a barrel or custom build issue.
If it were, then the rifles wouldn't feed perfectly with the Aero Precision bcg.

I always test each set up on each rifle with the same springs/ ammo/ mags etc to isolate the bcg variable- so, the only variable in each comparison is the bcg: Aero Precision bcg vs the JP Enterprises bcg_ (high pressure bolt)... everything else is the same.... the JP enterprises fmos bcg always fails to cycle... the Aero Precision bcg always produces 100% reliable feeds..
Something must be wrong with the JP enterprises fmos bcg/ high pressure bolt.
I've emailed JP Enterprises twice.... haven't heard back yet... I've wasted thousands chasing this issue thinking it must've been something I did wrong with my build... but, apparently, that's not the case.
What do yall think?

I’m interested in a light weight 22.
I would love to build a vudoo with a carbon barrel and HNT 26 stock, but a $4k rifle isn’t in the cards at the moment.

I have a 40% off Nightforce certificate I'm selling for $450. Good through 10/14/23. Paypal or Venmo. A picture will be emailed to you after purchase and shipped to you with tracking.

Gen 1 ATX cerakote in a black multicam pattern

Folding hinge, full enclosed forend, dependabuilt bag rider

6mm Dasher barrel in I believe stealth gray cerakote.

Chambered by Fritz @ black canyon customs with an alpha legacy reamer, 27” long 7.5tw 5/8x24 muzzle threads. Have approx 800-850 rounds down the barrel of a mild 31gr load of Varget and 105 hybrids. Getting 2880fps with 105’s. Ton of life left in this thing.

AX mag with HRD kit
Standard 308 AX mag

Wiebad cheek pad (never used)

Newer comp trigger set low at AI

Minor wear on the ARCA rail from match use. Has been run in matches but never abused in match settings (ie slammed into props, dropped, etc)

For the whole thing (minus optic and bipod and SR brake) I’m asking 6000 5500 and split shipping and insurance from my ffl to yours. I will entertain reasonable offers. This thing hammers, just have the bug to try something else again.

@BurtG no I will not take 2400 for it

Any questions please PM me. I’ll get the dust off before it ships. I don’t know why the photos are upside down but you get the idea.

Trades with cash on your end:
Impact SA AW cut action (308 bolt face)
Foundation centurion in black cut for an impact
Tangent 3-15M or P with a Gen3Xr
Maybe something else?

Original owner. Like new. I believe it is the LW17 model with QD.

$220 shipped conus. PayPal friends and family

First, “I’ll take it” posted here gets it. PMs don’t count. Questions welcome. No trades please.

Used in great condition. Only flaw is a nick on the tube shown in pic.
comes with box, manual, unused lens cloth and adjustment tool
SOLD shipped conus. Cashiers check, personal check (will clear both before shipping) or we can discuss electronic payment via PM.
insurance On the buyer

BBC reporter says he's seen a rise in hate speech since Musk aquired Twitter. Musk asks for one example. Reporter can't come up with one. Musk then calls him a liar in a Live interview.

I bet Chris Wallace won't interview him.

And I've seen less hate speech on Twitter after Musk took over and flushed the rabid anti-Trump/anti-conservative employees. But when one hears the term 'hate speech' and those that use it, it only applies to and is synonymous with conservatives.

Steve Van Zandt just this week called for the complete extermination of all GOP voters. But of course, coming from a NJ Biden sucking communist, thats not 'hate speech.'

Login to view embedded media

Would love feedback on this:

I am building my SHTF AR-15 (gathering all the parts rn before I have Cobalt Kinetics assemble (I really like their receivers and handguard setup and the fact that they are willing to work with me on a custom setup).

I have a Noveske AR-10 so I like heavy precision, but I don’t want the AR-15 to be DMR like that, more RECCE
I decided “let’s go with something more robust/fancy than their typical Rosco barrels they use (I’m kind of a gucci snob at times…)

So I decided to look at the barrel marketplace: hmm what’s the most expensive barrel I wonder? Well proof carbon fiber barrels came up on Primary Arms as the most expensive
I thought, well those look interesting, but so expensive … oh wait a 14.5” 1:8 twist 223 Wylde Carbon Fiber barrel On Sale for $699??

Now as an American, I am a sucker for sales/discounts like a fly is a sucker for a turd

As a SHTF rifle, I’m fine with spending money if it’s the BEST choice.

I have not seen a lot of Proof Carbon Fiber 223 Wylde barrels reviewed/discussed, so I want y’all’s opinions. I assume I haven’t seen a lot of reviews due to the price point more than any performance issue, but at $700 (instead of $900) it fell into a price point that I could stretch to, if it’s the best

It’s on backorder, so I could cancel and pivot, but it just seems like a great option
Would be running like 73gr eld-m or 55 gr v-max to start from Hornady is my thinking
Need to do more research there

Have a primary arms PLXC 1-8 on backorder as well, will be in a Scalarworks

RECCE is the goal
Defining RECCE as “light, precise, able to do battle” idk if that’s the actual definition

Do you guys think this would be a sick setup? Will this give me a precision weapon capable of battle?

Hey AI fans,

Kind of in a dilemma. I see plus’s and negs for both the AX and AT-X and can’t quite decide which route to go.

I think cost will be about equal once I add some weights and a bridge so price isn’t really a concern.

AIAX in .308 delivery around November…

AT-X in 6.5cm available now

I’ve kind of always wanted an AX but never did it and now the AT-X has come out too…


This rifle won’t be used for matches. Just me shooting in some wooded areas, clear cuts around BC and some ranges. Tripod and prone.

Having a tough time deciding

For the more experienced people here,What do you take in consideration for when picking out a scope,red dot,prism,lpvo etc. Features,weight,reticle,warranty,brand,where it’s made?

Catch and release of this beauty but with the addition of the Aimpoint Acro P-2 & Acro IOS Plate.

She has not been fired by myself.

Sold and purchased off of 1911 Addicts.

Add below:

SOLD - As New Nighthawk Custom -- Agent 2 -- Stainless...​

What a carry package here, this Brennon High built Agent II Commander had just 200 rounds fired before the original owner sent it back to the mothership for IOS installation, and refinish of the matte Stainless surface prep on this gun. Gun is unfired since its return. Gun is the complete...
www.1911addicts.com

No trades...will come with handgun, Aimpoint Acro & Acro IOS plate, original paperwork from purchase, two test fire sheets and original build sheet for IOS cut etc.

$5000 shipped FFL to FFL from AZ.

Wire Venmo or Apple Pay acceptable methods of payment.

Sorry gents, no trades as I have another HFB OG blade to secure.

Rob from AZ