I have two ATS Competition Tuners. They are both the tapered model and in excellent condition. They will come with the pictured hardware.

I'm asking $125 shipped each.

midgetoramaXGunny Sergeant
Rating: 3.1/5 this site
864 posts this site
338 Norma Loads
10/20/2014 Last edited 10/21/2014 by midgetorama

---

I am shooting a 9.5 twist Bartlein that finishes at 26".

With a 300 grain SMK I am getting slight ejector marks with 85.0 grains of IMR 7828 SSC and a CCI250 with Norma brass. Velocity is only 2715 fps.

The best accuracy with this bullet, powder, primer combo is 82.5 grains at 2632 fps. Single digit ES.

I am seating the bullet with a 0.025" jump.

I was expecting better velocity. I may try Retumbo eventually.
Rate now:
midgetoramaXGunny Sergeant
Rating: 3.1/5 this site
864 posts this site
Re: 338 Norma Loads
10/23/2014

---

300 SMK
GM215M
88.5 gr H-1000
COAL 3.565"
2690 fps with 12 fps ES over 10 shots
~0.233 MOA at 300 yards
Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
10/29/2014 Last edited 11/03/2014 by xdeano

---

Thank you for getting with us at Berger Bullets. We are glad to forward our updated Berger Load Data for use with your .338 Norma Magnum.




Please do not hesitate to get back with us if we can be of further assistance for you.



Kind Regards,

Berger Bullets Technical Support Team

[email protected]

----------------------------------------------------------------------------------------------------------------------------
Hope this load info from Berger would help someone out.
Xdeano

Rate now:
waveslayerXGunny Sergeant
Rating: 3.2/5 this site
855 posts this site
Re: 338 Norma Loads
12/04/2014

---

300 SMK

3.60

Fed215

Retumbo 87.5

Velocity at 2712 SD=8

DTA, 22" .338 Norma Mag AI, a damn tack driver

Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
12/15/2014

---

For those of you shooting Cutting Edge Bullets.

.338 Norma Mag. 225 gr, Cutting Edge, MTH D62 SF

O. A.L: 3.681" = 93.50 mm Barrel: 28.0" = 711.2 mm

!!! - YOU MUST START 6 grains UNDER LISTED, and WORK UP - !!!
Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
12/15/2014

---

.338 Norma Mag. 252 gr, Cutting Edge, MTH D65

O.A.L: 3 .681" = 93.50 mm Barrel: 28.0" = 711.2 mm

! !! - YOU MUST START 6 grains UNDER LISTED, and WORK UP - !!!


Rate now:
Thrust911

XFirst Sergeant
Rating: 3.4/5 this site
2180 posts this site
Re: 338 Norma Loads
02/25/2015

---

Any more load info to share? Particularity the 300gr Hybrid on top of H-1000?
I'm interested in velocity people are seeing out of 26" to 27" tubes.
Rate now:
TheflyingpoleXCorporal
Rating: 3.1/5 this site
60 posts this site
Re: 338 Norma Loads
02/27/2015

---

Any one try US869. 1smalljohnson told me to give it a try. I've just started messing with it. The highest I went was 99 grains and if I remember correctly I was in the mid 2700s. This was with a Berger 300 out of a 26" barrel. I'll post more after this weekend hopefully.
Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
03/11/2015

---

Im pushing the 300 otms at 2785fps.
88.7grns h1000
Fed 215mag primer
In a 26" tube, suppressed.
It shoots very well at a mile.

Xdeano

---------------------------------------------
--- Thrust911 wrote:

Any more load info to share? Particularity the 300gr Hybrid on top of H-1000?
I'm interested in velocity people are seeing out of 26" to 27" tubes.

---------------------------------------------
Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
03/11/2015

---

I have a good buddy that is using us869 in his 300rum pushing 230s. Ive thought about it, but what he is running into is a lot of carbon buildup, carbon ring.

If a guy is looking for a powder, definitely give rl33 a shot. Ive ran some of it and it gives excellent velocities.

Xdeano

---------------------------------------------
--- Theflyingpole wrote:

Any one try US869. 1smalljohnson told me to give it a try. I've just started messing with it. The highest I went was 99 grains and if I remember correctly I was in the mid 2700s. This was with a Berger 300 out of a 26" barrel. I'll post more after this weekend hopefully.

---------------------------------------------
Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
03/11/2015

---

Here is some info on rl33.
97.7grns rl33
300grn berger otm.
215mag
2863fps 26" barrel
3.725" coal - single load.
Es 14.22
Sd 7.00
This gave me a 0.103" center to center group at 100yds.

I did a quick velocity check prior to loading for groups.
1. 95.0grn-2738fps
2. 96.0grn-2788
3. 97.0grn-2732 - velocity dip.
4. 98.0grn-2861
5. 99.0grn-2899 - hard bolt lift

I shot these 5 rounds at 300yds and the resulting group was 2".
Xdeano
Rate now:
BobLSwagger

XFirst Sergeant
Rating: 3.6/5 this site
1419 posts this site
Re: 338 Norma Loads
03/17/2015

---

How did you manage to fit that much powder in the case with that longgggg 300gr Berger?

Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
03/17/2015 Last edited 03/17/2015 by xdeano

---

It'll fit...

I know it seems like a lot, but the density of the RL33 is higher then say H1000 where you'd have a hell of a time with 90grns.

xdeano
Rate now:
BobLSwagger

XFirst Sergeant
Rating: 3.6/5 this site
1419 posts this site
Re: 338 Norma Loads
03/17/2015

---

Looks like I'm going to have to give the reloader 33 a shot in my .338 Warthog... (.338 NMAI). I'm currently running 93gr of Retumbo with Berger 300gr OTM's @ 2893fps out of a 28" Bartlein 1:9.3

Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
03/18/2015

---

Definitely worth the try. You'll see how dense the 33 is.

xdeano
Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
03/18/2015

---

I've got some data for you on the US869.
90.0 - 101.3grns US869
300grn bullet
@100.0grns = 2710fps

Now this is not my data so start low and work up. Same as usual.

xdeano
Rate now:
Eric608XPrivate
Rating: 0.0/5 this site
5 posts this site
Re: 338 Norma Loads
03/19/2015

---

Has anyone tried the Lapua 300 grain bullets?
Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
03/20/2015

---

Whats the question? They will work just fine.
Xdeano

---------------------------------------------
--- Eric608 wrote:

Has anyone tried the Lapua 300 grain bullets?

---------------------------------------------
Rate now:
BonczykXCorporal
Rating: 0.0/5 this site
50 posts this site
Re: 338 Norma Loads
03/24/2015

---

My 28" Lilja 1-10 got:



2825 with 90,6 grains Norma 217 behind a 300 Berger Hybrid. COL: 3.6393.

2694 with 88,0 grains Norma MRP2 behind a 300 Berger Hybrid. COL: 3.6393.

Rate now:
garandmanXFirst Sergeant
Rating: 3.0/5 this site
1499 posts this site
Re: 338 Norma Loads
04/23/2015 Last edited 04/23/2015 by garandman

---

89.0 gr of H-1000 with 300gr Berger OTM

3.602 Cartridge Length ... I'm a couple thousandths off the lands.

Averaging close to 2800 fps from 27" bbl.

5-shot groups were 1.125 @ 200 yards.

I managed one 3-shot group at 200y for 0.625" NOT sure I could reproduce it.



I'd strongly recommend Berger boolits across the board. My 6.5 CM loves them too. Super high ballistic coefficient on both calibers.



My Retumbo tests for 338NM were averaging 2715 fps.

Rate now:
gewehrXGunny Sergeant
Rating: 3.0/5 this site
828 posts this site
Re: 338 Norma Loads
06/28/2015

---

26" bartlein 10 twist,

300 berger, 3.656" oal, 85.0 grains IMR 7977, 2710 fps

Rate now:
NormaMagXPrivate
Rating: 0.0/5 this site
36 posts this site
Re: 338 Norma Loads
07/26/2015 Last edited 07/26/2015 by NormaMag

---

xdeano

Close to 2900 fps from a 338 Norma out of a 26" barrel?

How is brass life?

I`m building a 338 Norma with a 30" Pacnor 1-9 twist barrel and hoping for 2850 fps with good brass life.

Rate now:
xdeanoXFirst Sergeant
Rating: 3.1/5 this site
1038 posts this site
Re: 338 Norma Loads
08/03/2015

---

brass life seems to be good. I'm not running a lot of the rl33. my main load is h1000 which i have previously listed on this page. but with RL33 a guy can get up there in velocity. Just giving the guys some insight. My numbers will vary from others.



xdeano

Rate now:
TheflyingpoleXCorporal
Rating: 3.1/5 this site
60 posts this site
Re: 338 Norma Loads
01/28/2016

---

Just saw this. Thanks. Life got in the way and I haven't messed with this in ages. Hopefully this weekend.

> xdeano wrote:
> > Theflyingpole wrote:> > Any one try US869. 1smalljohnson told me to give it a try. I've just started messing with it. The highest I went was 99 grains and if I remember correctly I was in the mid 2700s. This was with a Berger 300 out of a 26" barrel. I'll post more after this weekend hopefully.> I've got some data for you on the US869. Rate now:
SPAK7XFirst Sergeant
Rating: 3.4/5 this site
1777 posts this site
Re: 338 Norma Loads
06/19/2016 Last edited 06/19/2016 by SPAK7

---

Bartlein 30" 9:5 twist suppressed
89.0gr H1000 fed 215 Berger 300 otm coal 3.675"
2825fps sd 9
Barrel only has 72 rounds on it. Might see some increase in speed with some more rounds down the tube. We'll see.

Rate now:
Thrust911

XFirst Sergeant
Rating: 3.4/5 this site
2180 posts this site
Re: 338 Norma Loads
07/05/2016 Last edited 07/05/2016 by Thrust911

---

Area 419 built Deviant action in AI AX CIP length chassis.
Hawk Hill, 9.3 Twist, 27" tube.

215 Primer
88gr H1000 - zero pressure signs.

300gr Hybrid -- 2773 FPS avg SD 3
285gr Amax -- 2789 FPS avg SD 11.5

Rate now:
Thrust911

XFirst Sergeant
Rating: 3.4/5 this site
2180 posts this site
Re: 338 Norma Loads
08/16/2016

---

Settled on 89gr of H1000 pushing a 300gr Berger. Shot it on a ridiculously hot day...occasional ejector swipe, primers look good, no sticky bolt. At 1071 yards it hits steel with authority.

15k off the lands
AVG 2809FPS, SD of 4.3, ES of 9

Also will note that for my barrel the POI is the same for both 88gr and 89gr of H1000.

Rate now:
inferno218XSergeant
Rating: 3.1/5 this site
334 posts this site
Re: 338 Norma Loads
09/25/2016

---

Has anyone tried any 256 Flatlines yet?

Rate now:
SPAK7XFirst Sergeant
Rating: 3.4/5 this site
1777 posts this site
Re: 338 Norma Loads
09/25/2016

---

Not yet but it's definitely on the to do list...the 255 flatliners definitely have my attention for the Norma.

Rate now:
inferno218XSergeant
Rating: 3.1/5 this site
334 posts this site
Re: 338 Norma Loads
10/08/2016

---

I started working on my Warner 256 the other day and i think i am close to a load. I will have a chrono out next week and will post up numbers with load info.

Ran about 400 rounds of subsonics through it but use my MCX more. The upper was trimmed to run with a Super Safety, can't tell it was trimmed (ran like a champ).

BCM Upper
V7 6.5" 300Blk 1:5 Twist
Seekins MCSR V2 9" Handguard
FailZero NiB BCG
Radian Ambi Charging Handle

The handguard accepts 1.7" wide suppressors.

SPF shipped to you. If you want the SilencerCo 5/8x24 tri-lug add another $75.

I’ve had this a couple years. Planned to put a Q sliding brace on it and never did. Then I planned to put it in the XLR Atom chassis (other listing) and never did. Typical.

It’s in the original box. Great for a small backpack or truck gun. Never shot it.

It’s been ceracoated FDE and the stock is a sniper grey. Small k model magpul grip and magpul magazine.

Not sure what they go for now. Hard to figure out a price. Not many on the secondary market. It is a pistol. Sent from Remington as a pistol.

Asking $1600 OBO shipped. PM offers and will if you have questions. No trades at this time.

Anyone have some for sale?

I am looking for inexpensive but effective camo pants and jacket that are designed to wear over clothes. I am thinking something like a leafy suit or the mesh base to it. I prefer the mesh style vs the leafy style because I have ordered a few inexpensive leafy suits and the materials used in the leaf part has been shiny / reflective. I would like to keep the cost down as this is not going to be my primary hunting clothing. It needs to be light in weight and bulk to pack easily and well vented to stay cool. It will be used year round, so I prefer more grays, tans, & light browns vs deep greens. Thank you in advance.

Used for a few matches, $180 shipped

Recently purchased this, has maybe 50 rounds on it. It's a very good shooter with minimal recoil I just can't convince myself to like the 14.5" length. I prefer shorter barrels apparently, either way my loss is your gain. Mine currently has a KAC QDC flash hider, I have other mounts if you happen to need or want something else. Doesn't include all the rail scales or the optics, it's just the upper receiver.
asking $1000 shipped

here's the specs:
Product Highlights:

• Operating System: PWS Long Stroke Piston System with 3 setting Adjustable Gas System
• Chambering: .223 WYLDE
• Barrel Length: 14.5” 41V50 CMV
• Gas System Length: Mid-Length
• Barrel Twist Rate: 1:8
• Muzzle Device: Pinned & Welded PWS FRC 3-Port Compensator
• Upper Receiver: PWS Proprietary Piston Upper, 7075-T651 Forged, Anodized
• Handguard: PWS M-Lok™ 11.5” Handguard (1.7” width, 2.25” height)
• Charging Handle: Radian Raptor™ LT Ambidextrous Charging Handle

The LSS GEN 3 is now available for your CZ 457 and Tikka T3/T3x Long Action rifles!
Two new inlets, same rock-solid performance. Whether you’re running rimfire or long action calibers, the LSS GEN3 is now ready to elevate your build.
See here https://mdttac.com/us/build-your-own

Slightly used Kelbys Atlas Tac 308bf. Trigger comes with. 1000obo.

I made this bag rider for my rifle. I wanted something that was smooth and rounded all the way around the sides (full radius cut edges) to better fit against my tripod for rear support. Of course, still be good for rear bag use. Worked out well. I used to run the plastic dog leg looking bag rider from MPA (forget the name) and it sucked for rear tripod.

It is 4.9" long X 1.4" wide X 0.4" thick. 6061 Aluminum machined.

I have no idea if anyone is interested in these, I did not plan to make a run of them. MPA has a nice mostly flat one too for $50 bucks, I just saw no reason to buy one when I can make one on my machines.

Figured I would post it here and see if anyone is interested. Probably $40 shipped with Carbon Grey or Black Cerakote is what I would do. The one I cut for my rifle in the pic is Carbon Grey.

This fits my BA Comp using the 3 hole pattern on the bottom of the butt stock with 8-32 screws countersunk (see pic). May fit other MPA rifles, check for the hole pattern.

If I get say 6 folks interested, I will cut a run of them. Reply on this thread or PM me if interested.

Thanks,
Kevin

$500 gift card for Warne, $325

Great condition. They have Applied Ballistics onboard. As you can see in pictures, glass is very clean. Comes with box and bino harness. They work great, I just upgraded. $600 tyd.

If I ever get around his grave I'll be sure to piss on it.

It's flooding down in Texas , all the telephone lines are down , and my damn helicopter crashed. But seriously we're under tornado warning and it's storming like crazy but we need the rain ,so have to just grin and bear it.

3 new in wrap L3i mags for SOLD $140 shipped each

Good afternoon,

I have a Spuhr mount that was given to me. It’s an awesome mount but, I was wondering what (if any) warranty came with the mount?

Catch and release (mostly).
Sticking with the BRA.

Bought it from a fellow hide member,
some months ago,
here are the specs per them:

26"
5/8 threads
mullerworks
impact
1.25 straight contour
7.5 twist
6 GT
.120 freebore
Beanland Cut

It was new, but now has 83 rounds total on it.

Would like to sell as a package:
+ MDT Comp Brake
+ ATS XL Tuner

All for:
$old

Reach out with any questions, thanks!

These were made by Colton Arias of Bridger Forge in Nebraska. He is a two time winner of Forged in Fire and one heck of a blade smith.

Tanto with sheath - $475

Skinner/Hunter with sheath - $SOLD

Looking to buy a used matchmaster powder dispenser seen them on the for $600 shipped. Anybody have one?

Selling my LIKE NEW PRS Scope Top Bundle. I purchased and assembled this setup for scope top mounting for target acquisition. Not using it in the end.
The Acro P2 is like new. Spent its life wrapped in ranger wrap. Removed today. Minor blemishes from being moved around in the safe. It has the Tango down lens guard and Forward Control Designs Reinforced Battery Cover already installed.

The ADM Acro P2 Low mount is like new as well. Mounting screws shows wear from installation.

Priced as a bundle.

FOR SALE:

• One(1) - Aimpoint Acro P2 Red Dot Optic & Mount Bundle
  • Acro will include all OEM packaging , OEM battery cover and the red tool.
  • Selling with FCD battery cover. Like New.
  • Selling with Tango-Down lens guard installed. Like New. Comes with OEM packing included.
  • Selling with ADM Acro Mount "low" installed. Like New - NO OEM PACKAGING
  • Price: SOLD

I am open to hear reasonable cash offers. The worst I can say is no.

PM me first to avoid scammers. I will not PM you.

Accepting PayPal FF, Zelle only.

Will ship out same or first thing next biz day when possible.

Atlas Nyx for sale. Purchased in fall of 2024. Less than 500 rounds. 4.25” barrel. Sub 2lb trigger. Surefire light included. Three Atlas magazines (17 rounds) with Atlas range bag. Very clean.

Also included are the 2024 limited edition laser grip panels.

$4250 and free shipping to the compliant states.

Impact Precision Short Action Magnum 90 Degree Bolt. $375 shipped to you. PP Friends and Family

Leishy 2 PCP Air Rifle Upgraded Tank
HD Gen II Vortex 1-6X24
Scope Ring Cantilever
Magpul Bipod
Carbon Fiber handguard 275 Extra Mag

Crimson Trace Green Laser

3500 plus shipping