K&P 32” 1:8 twist 375 RUM barrel for TL3 short action. Muzzle threaded 3/4x20. 1.35” diameter shank for ~5.5” and then tapered to 1.1”. Has flats machined into the barrel for easy changing with switch barrel setup. Chambered by Michael DeLoach of 9 Run Gun. Weighs 8lbs 7oz. Also, comes with a custom tuner brake that was made for it.

You read that right. Poor man’s Cheytac. This is a 375 RUM barrel that I had cut for my TL3 short action to shoot ELR. If you are looking for the most affordable way to get into ELR, no question this is it. This barrel shoots the 390gr A-tip at ~ 2820fps w/ 105.3gr N570 into ~1/2 MOA (see pic below shot at 300 yards). Before I did this I called Zermatt and Ray said go for it, the action can handle it…so I did. Supersonic to 2450 yards at a DA of 5000ft…I got greedy and wanted even more out of it, and had it throated a little longer but it didn’t like it. SAMMI spec was fine, so I set the barrel back an inch (from 33” down to 32”) and now it has a fresh chamber in it that I’ve never even shot. I suspect it will be just like it was before…which was awesome.

Hornady Dies with micrometer seater.

74 pieces of Norma Brass. Started life as 300 RUM and necked up for 375 RUM as well as 50 pieces of new unfired ADG 375 RUM head stamped brass.

275 390gr A-tips.

Want to sell as a package. Will sell the A-Tips separately if someone buys the barrel etc.

$900/shipped for everything

Thanks,

Chase

Looking for a SA BDL style M5 footprint, referred to as a M4 trigger guard/bottom metal. In the white, cerakoted, or blued…i’m your huckleberry!

* SOLD * Very lightly used LabRadar. Comes with the custom soft case AND a piezo trigger that brings the frustration factor WAY down when shooting suppressed. Even works with .22s and air rifles! $199 shipped. Venmo, PPF&F, other methods may be arranged. Please PM any and all communication vs. posting here and opening yourself up to scammers. * SOLD *



Stuff I’m always looking for (whether you want my stuff or not):
APA Tru-Loc scope rings - 30mm .856"
Nightforce C550 ATACR 4-16x42 H59
Nightforce C644 ATACR 4-20x50 MilXT
S&B 4-16x50 cm ccw only, P4F or G2XR
Dillon carbide size/trim dies, 5.56 & 300 BLK
Harris S-BRM bipod
Factory Sig P320 full-size 1/2-28 threaded barrel
Emerson CQC Folder
L Reg surplus GoreTex

Other stuff I'm selling:
Sig P320 AXG Combat
TA01 4x32 ACOG
Ferro Concepts Bison belt
H&K PSG1 trigger
Timney SCAR 17 trigger
Misc cleanout

In good shape. Now $175 shipped and insured.

Zeiss dropped the 12x50 SFL binos today.
I have been messing with them for about a month or so.
Here are my impressions.
Login to view embedded media
ILya

On my 6.5CM I changed from shooting:
140 gr. berger @ 2690 fps (2250 ft-lbs) to 147 gr. ELD-M @2784 (2530 ft-lbs)

At 100 yards the 147 gr. load hits almost 1 moa higher than the 140 gr. load. Is the increased energy causing more recoil /muzzle flip resulting in the upward shift in POI? The 147 gr. load does have 12% more energy, but I am shooting a MPA rifle set up for PRS (heavy - w/ scope & bipod probably over 19 lbs.).

Used a couple of range trips then just sat in the parts bin. Comes with both collars for the carbine and rifle extension. Also throwing in a "blank end plate" and rifle extention.
$190 shipped.

Looking to build a 408CT after I finish up my SBR. What is the preferred barrel twist? Single fed BAT EX action, marriage ulr chassis, likely a Kriger barrel, acc sol bipod.

Have 3 identical Glock 19 Gen 3 "Brutta" complete ported uppers with Dauntless Engineering Acro Plate made by Lou Biondo of Business End Customs. "Morse Code” texturing, stainless steel match barrels, chunk ported, back bored, flushed high polish crown, cut rifled 1:16 LH twist for accuracy. SS Guide rod with spring and Ameriglo all black iron sighs and all internals. Cerakote Magpul FDE. Uppers test fired only by Business End Customs Lou Biondo.
Info from Business End Customshttps://www.businessendcustoms.com/product-page/bec-brutta-custom-g19-slide-barrel-combo
Info from Dauntless Engineering https://dauntlessengineering.com/product/acro-mps-adapter-plate/
$777 each includes FedEx Shipping CONUS
Payment- Zelle, Money Order

Various items getting cleared out over the next few weeks.

Badger Ordnance Conditon One FDE 1.93 34mm - $225

ZCO Block Mount 6Mil w/o diving board - $225
ZCO Block Mount 6Mil w/ diving board - $275

Reptilia AUS 1.54 30 mm with T2 ring cap - $250 sold

Q Cherry Bomb 1/2x28 (2) - $50 each sold
Q SR-25 3 prong 3/4x24 - $60

Area 419 12” Universal Mlok Arca (2) - $65 each sold

HK 416 BCG - $700 sold

I’ll hear out reasonable offers and I’m open to some trades (mostly, but not exclusively ammo). I’ll have more stuff in the coming weeks.

Steve

Anyone out there want to trade their 10 / 12 round AICS mag for my 5 rounder? Could add $ if needed.

It’s an AI brand mag. Barely used, in excellent condition. Feeds great.

Would sell for $55 shipped.

For Sale $1850 as a package to your door. This offer does not include diving board, level, or dope card holder. This scope is in good condition with minor wear marks from some comps and range use. I have the box for the scope and can (probably) dig up the box for the mount if you want it.

1 left!

VECTRONIX SHOOTING SOLUTIONS VECTOR 12x42 Rangefinding Binocular w/MSR-DMR Reticle 917238 $2,899.00 https://cstactical.com/vectronix-vector-x-rangefinding-binocular/

All the specs here: https://www.vectronix-shooting-solutions.com/products/vector-x/

New brass 200 count
$175 plus shipping

Thinking about biting the bullet and SBR-Ing a 300BLK AR pistol via Form 1.

I already have a gun trust with 5 suppressers so I will probably use my gun trust.

Anyone done one via e-forms recently?

Just looking for opinions before pulling out the debit card. After figuring out my ring height and deciding on rings over a 1 piece, I keep going back and forth between ARC and 419 rings. I've read pros and cons for each brand but for the most part they both have positive reviews and people seem to like them. I dont compete or really beat on my gear so these may be overkill for a .22 but I do like nice stuff. I like the simplicity of the one screw mount design of ARC and I also really like the mounting option on the 419 (bubble level) and I like the indexing pin built into them. Not a fan of the raw aluminum as I question oxidizing over time, but I also assume those guys know how to design their gear and would not have overlooked this if it truly were an issue.

I have one full box and one open 85gr RDF.
970 in total.
$320 shipped TYD

100 Berger 80gr VLD Sold

In immaculate condition and functions perfectly. Includes everything as if bought new other than 2 strips of Velcro. Was purchased just 2 months ago with hardly any use. Price is 1200 shipped, buyer covers PayPal fees

I recently built an 18” 6.5 Grendel with a NightForce NX8 2.5-20x

I went with the superlative arms piston system, but the BCG is tight in the upper so I may swap it over to DI with a superlative arms adjustable gas black and JP FMOS.
After researching the round more it really seems to be great at everything. So I’m thinking it may be cool to build a 13.9” SBR upper to have superior capabilities compared to my 300blk out and 14.5” AR and far less blast and recoil than my 13” SCAR 17. If I do that it makes total sense to swap the superlative piston to the SBR and I would use a VLTOR MUR upper since the BCG fits perfectly in that upper (my 14.5” AR setup). What I’m really wanting input on is… optic arrangement. While I’d have the 18” upper for long range, the 13.9” should be very capable out to distance. So I was thinking of trying the Steiner T6XI 2.5-15x with an RMR mounted on top. I’ve never used a top mounted or offset RMR, but I’m sure I can train to become accustomed to it. I thought this set up would make more sense than another LPVO. I’ve got a Trijicon Credo 1-6x on my 14.5” AR and a Trijicon Credo HX 1-8x on my SBR SCAR 17. Thoughts?
Use would be run and gun and up to whatever distance the rifle is capable. I’m thinking of trying the Lehigh 110 grain copper solids and the 110 grain controlled chaos.

Only 1 left, unopened Geissele SSAE-X Wide Body Lightning Bow trigger. Part number 05-960

$sold shipped in the lower 48

America rifle Co m10 rings
30mmx36mm high 125$
Was used on a pulsar thermion , work great on gas gun

35mmx24mm lows 125$

Mbrace rings
35mmx24mm low 135$

All prices are shipped
I will only message you from this account

Like title says. I have 2 of them with thread protectors in great shape and removed the carbon. $100 ea shipped.

Taxes due soon so I gotta gather up a few bucks to pay them…this has roughly 20 rounds through it. Defiance Classic action, Proof 24" 8-twist barrel, mesa full carbon stock, Hawkins BDL bottom, TI pro brake on it. Weighs sub 7 pounds, pics shows weight with a 24 ounce Schmidt Meta scope on it. In great condition, with some super small chips in one place on the butt. Priced to sell at $3900 shipped to your FFL. Thanks!

Mac

So for those of you that have purchased or thought about purchasing the Creedmoor TRX-925 scale and wanted to add a powder trickler here is what I found. I was on Accurate Shooter website and found someone was building a controller for the Dandy power trickler that would work with the TRX-925. I took the plunge and ended up buying the 2 speed Dandy and the controller. The price for both was well below other scale/trickler combinations. Combining the two was a simple matter drilling a small hole the the Dandy control box and soldering two wires. The controller has many settings that allow you to create different powder profiles.

It may not be as slick or fast as the higher priced combinations but it does offer an alternative for those of us with smaller budgets. It's my understanding that "itchyTF" who built the controller has three more available if this interests you.