• Watch Out for Scammers!

    We've now added a color code for all accounts. Orange accounts are new members, Blue are full members, and Green are Supporters. If you get a message about a sale from an orange account, make sure you pay attention before sending any money!

Range Report 6GT Project/Range Report

It’s a spreadsheet for load development that the 65 Guys made. It’s really handy.
You can find it here.
Awesome thank you.
 
Anyone buy Alpha brass lately? This is my first experience with Alpha and the case heads seem really soft. I did barrel break-in with 100 rounds of Varget at 32.5, 205M's, and 105 hybrids 10 thou off.. I can see faint extractor imprints. Not swipes or anything and the primers show no signs of pressure.
I'm getting alot of brass transfer to the bolt face as well.. it's strange.
Going to try some H4350 on the lighter side next.

Alpha brass always shows that.

Doesn’t matter what charge you use. You will always be able to see ejecter marks.

It’s not a pressure sign in this case.
 
Alpha brass always shows that.

Doesn’t matter what charge you use. You will always be able to see ejecter marks.

It’s not a pressure sign in this case.

Thanks.. that is good to know but it's not something I really care for.
H4350 seems to do it less for a given speed.
 
Had a good morning
For me anyway
844yd
105 bergers
In the cheap brass
shot_1582837556860.jpg
 
  • Like
Reactions: Dooby
Anyone having issues with alpha?

As low as 31.8 is giving me heavy bolt lift. PTG reamer from gap. Hornady not having this issue (at least not yet).

Seeing the issue with virgin and fired brass. Have tried everything from not sizing/sizing virgin, as well as turning/not turning necks.

Case length is well under max. Neck clearance is fine.

I’d say on average, 1:5 pcs of virgin brass and most all fired brass having issues.

Sizing die is sizing down to the .2 line. (I’d be looking much harder at die if virgin brass wasn’t doing it as well).
 
Anyone having issues with alpha?

As low as 31.8 is giving me heavy bolt lift. PTG reamer from gap. Hornady not having this issue (at least not yet).

Seeing the issue with virgin and fired brass. Have tried everything from not sizing/sizing virgin, as well as turning/not turning necks.

Case length is well under max. Neck clearance is fine.

I’d say on average, 1:5 pcs of virgin brass and most all fired brass having issues.

Sizing die is sizing down to the .2 line. (I’d be looking much harder at die if virgin brass wasn’t doing it as well).

i am running Hornady 105’s right now at 37.3 of H4350. Have ran250’s pieces of new brass and haven’t had an issue. Some of them have some force to chamber and force the bolt down but I figured that’s because they are new and I didn’t resize them.

I have 50 more new pieces to use then I’m going to resize and see if that goes away.
 
i am running Hornady 105’s right now at 37.3 of H4350. Have ran250’s pieces of new brass and haven’t had an issue. Some of them have some force to chamber and force the bolt down but I figured that’s because they are new and I didn’t resize them.

I have 50 more new pieces to use then I’m going to resize and see if that goes away.

Unless I’m having an issue and need to verify without sizing, or unless I’m using a chamber already set to .005-.006 neck clearance, I’m turning my brass to get that clearance. So I end up running it all through a sizer to get the next tension sorted back out (bushing down and mandrel up).

I haven’t run into a problem with hornady as of yet. But alpha has had issues in two barrels on two rifles (same reamer, so that is a possibility at the moment as the culprit).

I also have had/have similar issues with alpha dasher. So, slight pattern forming.
 
Unless I’m having an issue and need to verify without sizing, or unless I’m using a chamber already set to .005-.006 neck clearance, I’m turning my brass to get that clearance. So I end up running it all through a sizer to get the next tension sorted back out (bushing down and mandrel up).

I haven’t run into a problem with hornady as of yet. But alpha has had issues in two barrels on two rifles (same reamer, so that is a possibility at the moment as the culprit).

I had/have similar issues with alpha dasher. So, slight pattern forming.
Isn’t there just the one GT reamer that everyone is using so far?
 
Isn’t there just the one GT reamer that everyone is using so far?

Yes. Same specs across the board.

I was speaking in general terms of neck clearance. A lot of reamers (across calibers) that are “no neck turn” are set up for .003 or so clearance.

That should be called a “neck turn not required” reamer. It’ll work, but a lot of people prefer something a little more like .006.

GT is a .273 neck. Most loaded hornady and alpha will be around .269-270
 
Anyone having issues with alpha?

As low as 31.8 is giving me heavy bolt lift. PTG reamer from gap. Hornady not having this issue (at least not yet).

Seeing the issue with virgin and fired brass. Have tried everything from not sizing/sizing virgin, as well as turning/not turning necks.

Case length is well under max. Neck clearance is fine.

I’d say on average, 1:5 pcs of virgin brass and most all fired brass having issues.

Sizing die is sizing down to the .2 line. (I’d be looking much harder at die if virgin brass wasn’t doing it as well).

have you checked measurements near the head? my guess is that the alpha is thicker and especially at the head and the sizing die is not sizing the base enough...i had the same issue when i shot a BRX...every couple of firings i had to small base size and finally bought a custom from whidden...try small base sizing and see if that helps...if you dont have a small base die i have one you can borrow if you want.
 
have you checked measurements near the head? my guess is that the alpha is thicker and especially at the head and the sizing die is not sizing the base enough...i had the same issue when i shot a BRX...every couple of firings i had to small base size and finally bought a custom from whidden...try small base sizing and see if that helps...if you dont have a small base die i have one you can borrow if you want.

Happening with virgin brass and not just fired. So, either the brass is issue or the reamer at this point.
 
Last edited:
I have not had pressure issues with Alpha brass. Virgin or once fired. GAP reamer. Hybrids and SMKs. 38gr H4350 and 39 - 40gr StaBall.

3 thou is bare minimum neck clearance. I like 5 thou. 1.5thou is a tiny measurement.

I know this sounds stupid but I've done it. Maybe check:

That you're loading out of the jug of Varget. That you didn't accidentally pour a faster powder in the jug thinking it was Varget to consolidate two different bottles.

Massive coppering

That a bullet will slide freely into the neck of a fired case

Donuts? (Can't be on virgin brass)

What are the headspace in between virgin and once fired?

Bullet slides freely

Less than 100rnds on this barrel. Can’t be copperin

I only have varget in the house for this reason. Use it in .223, .308, 6br, dasher, and 6gt. No other powder here.

Shoulders only moving .005 (.007 on some at the very most, but usually .005 from virgin to fired)

I’ve eliminated almost everything possible down to two variables left:

Brass

Reamer

And so far, hornady brass works.......
 
  • Like
Reactions: reubenski
@Dthomas3523

Do you know the lot numbers for your alpha brass by chance?

If they are the same as mine I'll check my supply in my gun for reference. Maybe help you narrow some things down.
 
Happening with virgin brass. So, either the brass is issue or the reamer at this point.

thats what i mean...maybe the head is a little big to began with then when fired even more then sized and not enough with spring back.
with my BRX im prttey sure the reamer was just a bit under sized.
 
thats what i mean...maybe the head is a little big to began with then when fired even more then sized and not enough with spring back.
with my BRX im prttey sure the reamer was just a bit under sized.

It could be. I’ll measure again. I’m pretty sure my die sizes all the way to the base properly. I checked a few weeks ago when I had issues with fired brass at a match and it was sizing down.

I had similar issues with dasher brass and have been contacted here and on FB by numerous people via PM who have been seeing issues with brass (mainly dasher) as well.

I’m slowly coming to the conclusion that if lapua doesn’t make brass for it, I’m not chambering a barrel for something until they do.
 
  • Like
Reactions: 47guy
It could be. I’ll measure again. I’m pretty sure my die sizes all the way to the base properly. I checked a few weeks ago when I had issues with fired brass at a match and it was sizing down.

I had similar issues with dasher brass and have been contacted here and on FB by numerous people via PM who have been seeing issues with brass (mainly dasher) as well.

I’m slowly coming to the conclusion that if lapua doesn’t make brass for it, I’m not chambering a barrel for something until they do.

this is why i went away from the BRX because of similar issues plus the fire forming...ive also went away from lapua brass in favor of peterson...the peterson handles pressure much better in everything ive shot it in.
 
  • Like
Reactions: Dthomas3523
Conclusions I’ve come up with after a couple barrels:

Reamer out of spec
Brass out of spec
Brass hardness issues
 
Dthomas, did you get the lot numbers for your brass? Maybe yours is the first batch? I have some Alpha, waiting on my barrel.

I’ll have to look and it’s likely mixed up with several lots.

When I pay $1.15/per, I don’t expect to need to keep track of lots for functionality when there is a single standard reamer spec for the design.
 
  • Like
Reactions: I SHOOT and 47guy
If you have several lots, doing the same thing, it probably doesn't matter anyway. I agree, at the price differential between Hornady and Alpha, you should not have to track lot numbers. I have 200, all the same lot. When my barrel arrives I'll post more, if this thread is still going.
I wish we could get a sticky in the Reloading Depot. External ballistics is an odd place to track reloading.
 
If you have several lots, doing the same thing, it probably doesn't matter anyway. I agree, at the price differential between Hornady and Alpha, you should not have to track lot numbers. I have 200, all the same lot. When my barrel arrives I'll post more, if this thread is still going.
I wish we could get a sticky in the Reloading Depot. External ballistics is an odd place to track reloading.

Hornady is performing very well so far.

I’m actually on my way to have a guy change one of these barrels to 6x47.

Will have

6gt
6br
6x47

Barrels to compare this year and see how they do. Basically a side by side of the three that are related in design or intended use.
 
  • Like
Reactions: 47guy
Hornady is performing very well so far.

I’m actually on my way to have a guy change one of these barrels to 6x47.

Will have

6gt
6br
6x47

Barrels to compare this year and see how they do. Basically a side by side of the three that are related in design or intended use.

run a 6BRA reamer in that 6BR barrel and run peterson brass fed205M and varget and i bet youd be a happy man.
 
  • Like
Reactions: Dthomas3523
Bullet slides freely

Less than 100rnds on this barrel. Can’t be copperin

I only have varget in the house for this reason. Use it in .223, .308, 6br, dasher, and 6gt. No other powder here.

Shoulders only moving .005 (.007 on some at the very most, but usually .005 from virgin to fired)

I’ve eliminated almost everything possible down to two variables left:

Brass

Reamer

And so far, hornady brass works.......
I've got 250 hornady
On their 3rd firing 0 issues I'll be sticking with them!
 
Is it hard bolt lift or hard extraction? I had some brass that was fired out of someone else's chamber and after the first firing would get stuck in the chamber. It was low pressure but the previous chamber that this brass was fired in was a little bit larger and I needed a SB sizing die. I did not have heavy bolt lift but I damn near couldn't extract a fired round. I had to take my barrel off and push the case out with a rod. Once I ran the brass thru a SB die, I never had the problem and I also didn't need the SB die after the first sizing.

I created a similar problem with a 6Creed using Alpha brass. I ended up with a too hot load and it expanded the webs on all the brass. It happened during a match and so I affected 100cases. I had to remove my barrel during the match and pull brass out with a Leatherman. On the clock. On the last three stages. The Redding die couldn't rehab the bases and I essentially created the same problem as above. That brass is ruined. I tried to order a PVA SB universal die to resize the webs but they sent me the wrong bushing for two months and then when I finally got them to realize a .463 bushing was too small for a .470 web they realized they didn't have any correct bushings. So $200 of Alpha brass and a $200 die are just sitting there until PVA makes the right bushing. It's been 5 months?

Typically with fat webs and too fat dies and too skinny chambers you don't get hard bolt lift but you get hard extraction

Bolt is easy until just before the cam. Basically as it’s getting to where you’d see most 60deg open (this is a 90), it sticks there and I have to apply a lot of pressure or hit the bolt open with my palm.
 
So, basically a primary extraction issue. Even with virgin on light loads.
 
So, basically a primary extraction issue. Even with virgin on light loads.
So trying to follow along with this
You've used both Hornady and alpha brass in the same rifle and your only having the problem with the alpha correct?
 
  • Like
Reactions: Dthomas3523
So, basically a primary extraction issue. Even with virgin on light loads.

That would say to me that it's nothing to do with pressure, it's all about primary extraction. And that relates to base diameter usually.

I measure base diameter with a vernier micrometer instead of calipers, bit more accurate that way. I lay the micrometer flat on a table and measure the base/web at the fattest area by standing it on the case head. I ran into difficulties with primary extraction if the base diameter was less than 0.0004 smaller than chamber size. Once I get to 0.0006 or more sizing the clickers go away. If you haven't seen this one before it's a good breakdown.

 
That would say to me that it's nothing to do with pressure, it's all about primary extraction. And that relates to base diameter usually.

I measure base diameter with a vernier micrometer instead of calipers, bit more accurate that way. I lay the micrometer flat on a table and measure the base/web at the fattest area by standing it on the case head. I ran into difficulties with primary extraction if the base diameter was less than 0.0004 smaller than chamber size. Once I get to 0.0006 or more sizing the clickers go away. If you haven't seen this one before it's a good breakdown.



Agreed. However, there is a problem.

Either the brass is oversized or the reamer is undersized. That’s what I’d like to get to the bottom of. Something isn’t matching up between the chamber and the brass.
 
Either the brass is oversized or the reamer is undersized. That’s what I’d like to get to the bottom of. Something isn’t matching up between the chamber and the brass.

True, but long term it becomes more of a question of whether the dies match the chamber. If the dies give adequate sizing then all you need to do is run the virgin brass through the dies before first firing.
 
Agreed. However, there is a problem.

Either the brass is oversized or the reamer is undersized. That’s what I’d like to get to the bottom of. Something isn’t matching up between the chamber and the brass.
I apologize if you’ve already done this. Do you have the measurements on the base and shoulder diameters on Hornady vs Alpha, virgin, fired, and sized? That should clear up any differences. If the dimensions for both brands are identical throughout the firing process, then the Alpha brass itself could be the culprit.

Do you own your reamer? If you have it in hand you could try to measure the base diameter. I’m gun shy on PTG reamers, so I waited for a JGS.
 
So, it'd be hard to gauge the hardness of the brass without some tools. One other thing you could check that might show a dimensional issue with the Alpha stuff is to measure case capacity via the water method? Maybe measure a Hornady, too? I'm not intimately familiar with GT, but it seems like 31.8 should be a super light load. If the case volume is significantly lower in the Alpha stuff (thicker walls, etc), obviously that could be an issue.

Past that, based on everything else you've looked at and tried, I'd start to blame the brass (just because Hornady brass works fine - if they both had issues, I'd look at the chamber first). There are a few other things you could compare between the two - like flash hole size, etc, but those should be minimal factors. You could potentially have someone measure the reamer (or chamber), or cast the chamber, and determine the final dimensions, but ...
 
  • Like
Reactions: Dthomas3523
So, it'd be hard to gauge the hardness of the brass without some tools. One other thing you could check that might show a dimensional issue with the Alpha stuff is to measure case capacity via the water method? Maybe measure a Hornady, too? I'm not intimately familiar with GT, but it seems like 31.8 should be a super light load. If the case volume is significantly lower in the Alpha stuff (thicker walls, etc), obviously that could be an issue.

Past that, based on everything else you've looked at and tried, I'd start to blame the brass (just because Hornady brass works fine - if they both had issues, I'd look at the chamber first). There are a few other things you could compare between the two - like flash hole size, etc, but those should be minimal factors. You could potentially have someone measure the reamer (or chamber), or cast the chamber, and determine the final dimensions, but ...

Or.....

174B9067-0478-40BE-B97D-2A43BE0CC1C0.jpeg
 
  • Like
Reactions: phlegethon
If hornady holds up a few more firings, I’ll be confident to continue with gt
 
6x47L was such a great cartridge for me for 13 years, no problems but I did have one custom size die I sold with a rifle, and then a Warner die.

Owned my own reamer that whole time and still have the brass with 38+ cycles on it that holds a primer well. Last load was 3172 fps with 105's in a 28" barrel.

Have your smith throat it out some more then use H4831SC.

Lapua brass man!
 
No way!
That's why I went with the GT instead of the dasher hated the thought of forming the dasher brass

Well, look at what guys like Dan and Vu did at the beginning of this thread... before Hornady brass came online... Original GT brass was formed from 6.5x47... that's the brass prep @phlegethon was getting at...
 
  • Like
Reactions: phlegethon
Well, look at what guys like Dan and Vu did at the beginning of this thread... before Hornady brass came online... Original GT brass was formed from 6.5x47... that's the brass prep @phlegethon was getting at...
I've read this thread and the duplicate one on accurate shooter
Real good stuff.
they said plainly making the brass was a pain.
I was planning a Dasher build but when hornady brass was available I was sold and glad I did
It's an awesome little cartridge.
 
It's not a hard puzzle to solve. It is frustrating. Think of all the 6XC Gen 1 vs Gen 2 vs 6-22/250 drama that's out there.

If you don't know how, ask your smith. Or PM me. I've read your other posts, you seem very knowledgeable, and obviously can shoot.

The Reamer->Virgin brass-->Sizing Die all have to be on the same sheet of music. If they are, then it could be a banana chamber, banana die, or a bad lot of brass (rare).

Base diameter [email protected] north of case head
Base diameter of virgin Hornady
Base diameter of virgin Alpha
Base diameter of fired Hornady
Base diameter of fired Alpha
Base diameter of sized Hornady
Base diameter of sized Alpha

If you have a sticky fired Alpha and then another not sticky fired Alpha, add that into the list above.

If your annealing, describe your annealing practices.

If you capture the above dimensions one of them will usually stand out. If it doesn't, then look at shoulder diameter .050 south of body/shoulder junction, and capture the same dimensions.
 
Last edited:
I have 800 rounds through my barrel, still half moa. I'm running it slow at 2900 with 34.3 GN of varget. All alpha brass but I did notice that my bolt was sticky with once fired. I'll try resizing down an extra .002.

I cleaned the chamber at 600 rounds when I heard Dthomas having issues. So far I'm liking the less recoil over the 6.5, gonna keep adding to the barrel life.
 
  • Like
Reactions: Dthomas3523
I have 800 rounds through my barrel, still half moa. I'm running it slow at 2900 with 34.3 GN of varget. All alpha brass but I did notice that my bolt was sticky with once fired. I'll try resizing down an extra .002.

I cleaned the chamber at 600 rounds when I heard Dthomas having issues. So far I'm liking the less recoil over the 6.5, gonna keep adding to the barrel life.

Awesome. And either only half of my issue was the dirty chamber. Could have been 100% brass though. Will be experimenting a bit more here shortly. But for the moment I’m working on another more proven cartridge so I have something to shoot matches with until I have this worked out properly.
 
  • Like
Reactions: sleeplz
@Dthomas3523 I know it's an expensive option, but have you considered a custom sizing die? I've been looking at (and lusting) over a Warner Tools sizing die for years. Since I shoot so few calibers, I think I'm going to take the plunge. I own my 6GT and 6.5x47L reamers, and have large lots of brass, so it makes sense to me. You have the ability to spec out exactly what you want, and the die is made from your fired brass and reamer print.

Not saying that's the solution to what's going on, but a $600 die and swappable caliber inserts might be cheaper in the long run than spinning up a new barrel, buying brass, AND new dies for a 6x47L.

I also have an odd issue with my 6.5x47L, where regardless of sizing die (I've tried 3 different brands), I have to bump my shoulder back 0.003 - 0.004" in order to close the bolt with no resistance. I can't figure it out for the life of me, but I know I'll be cutting the life of my brass by sizing that much each firing.

Also, have you had your 6GT reamer inspected? I've heard enough horror stories about PTG to know it's possible that the reamer is the issue.
 
  • Like
Reactions: steve123
I agree with investigating the reamer - PTG has notoriously bad QC. I know gunsmiths that won't even use reamers from PTG.

That's probably the first thing I would look at.