• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Search results

Search the forum Search Articles
  1. Y

    Barrel Choice

    I to like Bartlein for my first choice with kreiger a close second I think both would perform very well and thank you for your service it is greatly appreciated good luck
  2. Y

    Gunsmithing Easy Question about action bolt

    J B weld should work to but when you tighten just snug it up don’t torque like you would the action screw because all it’s holding is the back of trigger guard
  3. Y

    Gunsmithing Distinct ring around fired case neck.

    Doesn’t look bad enough to cause problems probably caused by a nick in the reamer or a shaving stuck to it can you feel it stick out with a pointed object or is it like a scratch maybe check the chamber with a light to see if a peace of brass or something imbedded in the chamber that could be...
  4. Y

    Gunsmithing Pre-fit Barrel Headspace

    You can just use the brass but should be a fire formed one from another gun I have seen Vergin brass lengthened in the shoulder area up to 15 thousands so a fire formed would work best and do it just like supercorndogs said good luck
  5. Y

    Gunsmithing Dial indicator with a long contact point

    The intrepid is a outstanding indicator I also like the mitutoyo 513-512 it’s small enough to fit up the chamber an extra inch or so
  6. Y

    Gunsmithing Dial indicator with a long contact point

  7. Y

    Gunsmithing Removing Badger Thruster Brake

    A plumber strap wrench might work also
  8. Y

    Gunsmithing Removing Badger Thruster Brake

    The best way is to make a tool out of aluminum 3/8 Or 1/2 inch you can take a Piece of aluminum drill and slightly bigger than a brake then cut a slot from hole to edge and thread it with a cap head screw so it squeezes the brake and give it a good tap with a hammer and should come loose or if...
  9. Y

    Gunsmithing Badger M2013 light primer strikes?

    Sorry didn’t Proof read my post but it should say not sure if this helps good luck
  10. Y

    Gunsmithing Badger M2013 light primer strikes?

    It could be the trigger timing not familiar with badger actions but if the cocking peace on the bolt is to short it doesn’t hold the firing pin back far enough to have enough momentum to hit the primer hard enough not if this helps but good luck
  11. Y

    Gunsmithing Bore condition

    Sometimes accuracy loss can have nothing to do with the throat but more to do with the crown just cleaning can wear the crown and make it not shoot and if it was me I would not set back a barrel because why pay for the work to be done with no Guarantee that it will do any good I would just bite...
  12. Y

    Gunsmithing Muzzle threads

    If it were me I would go 5/8-24 if the barrel is large enough to do so it’s really the barrel that dictates size of thread if its a Thin barrel then you would have to go 1/2-28 always go with largest thread you can but some time equipment will dictated thread size also good luck
  13. Y

    Gunsmithing Is there a best "go no go" gauge to set headspace for accuracy?

    The biggest thing when loading for Accuracy Is setting up your Die you need to use a oal gauge that measures of the shoulder and only size the brass until it chamber with maybe a little resistance but they should all feel the same when chambered I usually bump the shoulder a thousand of an...
  14. Y

    Gunsmithing Anyone ever build on a Remington 600 action?

    i built a 6 mm br on one it’s incredibly accurate nice action as far as I’m concerned I would build on one again
  15. Y

    Gunsmithing X-Caliber barrels

    I screw up again the groups or from same rifle it sucks to get old
  16. Y

    Gunsmithing X-Caliber barrels

    Sorry didn’t realize what wrote did get in my post these 2 groups are from 2 different 308 win don’t think I have had any shoot more than 1/2 moa all i know is they shoot better than i can
  17. Y

    Gunsmithing X-Caliber barrels

    [No message]
  18. Y

    Gunsmithing Stainless vs Carbon steel actions (.308)

    I doubt you would Wear out either one unless you shoot a lot of competitions for many years but some people prefer Chromemoly because it is less likely to gall the locking lugs like stainless will if you don’t keep It lubed with Grease
  19. Y

    Gunsmithing Remington 40X action screw torque?

    On the ones I have had I would torque to 45-50 inch Pounds if it doesn’t have Pillars but just pay attention to the feel you can feel when you start crushing the stock hope this helps good luck
  20. Y

    Gunsmithing Who to go to for modifying this....

    I would second on chad at LRI Plus he has fast turn around
Top Bottom
Back
Home
Forums
Merch
Alerts