Search results

I use a LNLAP to load pistol cals and .223, and a RC for other rifle cals. The RC has the Hornady LNL conversion. I added almost 1/8" of shims under the LNL conversion to make the die adjustment the same for both presses. Has worked great for me.

I load precision .223 on a LNLAP, and shoot it out to 800 yards from a 26" WOA varmint AR. It'll stay under about 3/4 MOA vertical, but windage, well, windage requires some ability.;) I use 77 gr Noslers, Win cases, Rem 7 1/2 primers, and 24.0 gr of Varget individually weighed. 24.0 gr of TAC...

According to Hodgdon's burn rate chart ( Burn Rate ), N140 falls between Varget and RE15. I don't use N140, but I use a lot of Varget and RE15 for 77 gr loads. Works well out to 800 yards.

Still 3 lbs left....

To quote my dad, "The best time to plant a tree is 20 years ago. The second best time is now." It applies to reloading too. Some components are as hard to find as unicorn horns. But buy what you can when you can find it, and work out a 'plan B' for the rest.

All Gone now..... But, thanks, anyway.

80s should be fine in a 1-8. I have been shooting 80s gr. Noslers in my 1-9 Savage bolt gun successfully.

I've been using the 105 Amax (non moly) out of my older 700 BDL Varmint using 41.0 gr of H4350. Work up your loads to 41.0 gr. carefully, since it is at or above max book loads. It shoots sub-MOA out to 800 yards; haven't tried any farther yet. Chronoes at 2910 fps in mine. 400 yards is...

Do you get the same FTF percentage with factory ammo? Or is it only with your reloads? Tell us about your reloading setup and processes. Did you use a case gage to set up your sizing die? Do the FTF rounds fit in the case gage? Do you lube the inside of the case mouth when sizing? If the...

Try this, it's the Ponsness/Warren site: http://www.reloaders.com/owners_manuals/duo-mat_375_manual.pdf Ponsness/Warren, Online Shopping for Recreational Shooters There's s phone number on the front page, and address at the bottom.

I've tried several of the cheap (sub-$50) digital scales and found them all to be worthless for measuring powder. Too much drift. I think as long as you don't go cheap, any of the name brand reloading scales work just fine. If your budget is under $80 - 100, don't waste your money on a...

Try CH4D. They list a Dillon trim die for the 260, but not for the 338LM. Caliber List : CH4D

Great write up. You can get started in reloading on the cheap and still produce great ammo. I know several shooters that started reloading while living in a cramped apartment, and what they did was bolt their press to a 2x6 long enough to reach across their kitchen table or counter, and used...

Drillspot.com used to be the place to buy corncob media, but they charge too much for shipping now. Try Zorotools.com: Blast Media by ECONOLINE - Pneumatic Blasting Media by Zoro Tools Industrial Supplies Shipping is only $5, and free over $50. Still a part of Grainger.com. Also, there...

I shoot a AR with a 26" 1/7 barrel, and mostly use Varget, too, but with 77 gr SMKs. Almost as good as Varget for me has been TAC, IMR4320, RE15, and WW748. Varget, TAC, and RE15 are hard to find but the 4320 often shows up locally. It meters better than Varget, and often produces groups...

That separation area is typical for .223 brass that is headspaced .008" too short. Yes, they can separate even on the second firing. A straightened paper clip with a bent tip can be used to feel the inside of the cases that have had the shoulder pushed back too far. You can feel the groove...

I've had good performance in .243 Win with 70 SMKs and in .223 Rem with 77 SMKs

I have the dimple too. My fix has been to just stick a dime over the dimple to give the primer seater more stroke.

What you describe is usually a headspace issue. Did you use a headspace gage to set your FL size die? While a Small Base size die could be needed in your rifle, yours would be the first I've seen that actually needs it. Most just need a properly adjusted FL die set. I started out with a SB...

When my AR varmint barrel (1/7" 26" WOA) was brand new, about every third round of Berger 55 gr. Varmint bullets did vaporize at 75 yards out or so. I think the ragged barrel grooves helped to tear the bullet jacket. There was a lot of copper left in the barrel after shooting. Since it's...