Search results

It has been a few years since I wrote Reloading 101 and I have commented several times that I should update it. Well I guess now is as good a time as any. This mental wandering is not comprehensive, it is “in addition to” the previous article. As...

Reloading Basix: After helping quite a few folks recently getting set up for reloading I decided to put my thoughts on paper. Here is my spin on how to turn out good quality ammunition for precision/tactical rifle at minimum cost and minimum fuss...

This is your answer. You cannot expect to have a consistent CBS after you clean a rifle. Once it is dirty, leave it that way. If it jumps off zero then you have other issues. Your ammo lot numbers may have an effect also as noted. Cheers, Doc

I know for a fact that there is one of those kitty's in Pungo, VA. That's just a couple miles south of Virginia Beach. Cheers, Doc

Shoot it. Just be aware that your POI may be different after you brake it. Cheers, Doc

Sub MOA at 1K+, 90% of the time out of the gate? Not this cowboy. I'd scare the hell out of it 90% of the time but hitting it, not so much. I'd go 600 for a CBS with that percentage given your atmospherics. In an any condition, any time CBS (within reason), 450 - 500 yards. Cheers...

Sitting at MCAS Miramar trying to figure out who this new guy living in my house was. He seemed to like me just fine, but I'd never met him before and he walked with a limp. Welcome home Dad! Sorry for puking on your Dress Blues and on General Krulak's shoes. Cheers, Doc

Most hunters are "Set it and forget it" scope users. They shoot a box of ammo left over from last year and buy a new box this year. They also set up an 8" paper plate at "about" 100 yards and if they hit it 4 out of 5 times they proudly proclaim their rifle "sighted in". Precision shooters on...

Never mind thought you were getting a 1.8 - 10x Cheers, Doc

Damn, 50% 50% I got two smart phones ;) Cheers, Doc

50.14% Stowe 49.86% Woodstock Cheers, Doc

This is the correct answer. The hard stops at either end of the power ring are the only TRUE points you have. If it was me I'd be checking the top end for the correct line spacing also. Not that I have ever seen 7 out of 10 Leupy scopes unable to be dialed to the correct subtention in one...

50.51% Stowe 49.49% Woodstock Double dipped from home :P Cheers, Doc

Not UPS centric but is it me or have there been a whole lot of trains falling off of tracks recently? Like 4 in the past 2 weeks. Cheers, Doc

50.23% Stowe 49.77% Woodstock Cheers, Doc

Short version: Utilizing the concept of aim small, miss small you pick a very precise point on the target, say the intersection of two lines. If your rifle is dialed in and you take a shot and the bullet hits that aiming point but not perfectly you no longer have the same spot you were aiming...

Yep, not HS but same principle and truth be told I think B&C does a better job with their blocks. Before looking for a bedding smith I'd get a torque wrench and pull the action. With just an allen wrench I'd put the screws in one at a time and see if (visually) the action lifts on either end...

Well it was a thought. Is that action bedded per chance or riding on an aluminum block? I had a similar experience with my Winny HBV until I started messing with torque settings when it was in the original HS-P stock, it was resolved completely when I bedded the action to the block. Cheers, Doc

You are experiencing split groups. "Generally" it comes from losing position in the middle of the string. Whether it be from attempting to stay in one position or more likely in the case of a 338, not noticing that your position has changed. When you do toss the shot you think "%^#$" and you...

IMHO a properly set up FL die will work your case less over time than neck/body/FL when it's TOO big. The piece of mind that comes with knowing it's going to work EVERY TIME is priceless. Cheers, Doc