mount

Been searching here and there for a pre-drilled rail to mount an Atlas bipod on my 10fp. Without much luck. Factory tupperware stock with the swivel studs at 2.5 inch on center. OH and BTW where can one find Swivel Studs in various sizes and lengths? Looks like I need to just buy some raw...

hey guys, I ordered a EGW 20 MOA scope mount for my Remington 700 SPS Tactical (.308). Im going to put a Leupold 4.5-14X50 Mark 4 LR/T on the mount. Anywyas....I ordered the 20 MOA version but SWFA is out of them and told me they could ship a 15 MOA today or I could wait 14 days till they get...

Got an M1A with a Gen 3 scope mount on it that I am trying to get off. It is going to be replaced by a Sadlak or GDI in the near future. Is there a set screw that keeps that dove tailed piece mounted to the receiver? If so, what size of allen wrench or other tool do I need to get it out...

Well, I just got my EGW base and removed the old 2 piece base. It apperas there is some sort of bedding compound put there by the guys at Dick's when they mounted the scope there. I tried removing it with Acetone and Goo Off, but they didn't work. So, I scraped it off and got most it off, but...

Finally mounting up the Ken Farrell 20MOA base and putting the Falcon Menace on my Savage 110. I found lots of good advice here via the search and FAQ on leveling and everything, but I can't find any info on how to fix my issue, which is this: When I torque the base mount screws, they bind the...

Is there anyway to add the AI spigot Bi-Pod mount to an AE rifle that just has a the plastic plug? Thanks for any help.

I recently acquired a picatinny rail mount for m14/m1a with the following markings nsn5855-01-506-5730 u.s. property. can anyone tell me who manufactured this mount? will try to get pics up later. Thanks

I am playing with the idea of getting the Larue mount that holds the ACOG and puts a AimPoint Micro T-1 on top of it. Anyone seen these or shot with one? I have never looked through that size Aimpoint and wonder if acquisition times would be slower than an Eotech. I am currently set up to be...

has anyone tried using TPS rings on PRI scope bases? is the base slightly too wide or do they fit?

I didn't like the fact that I had to give up my rear irons, but I did try the LT100 and did not like it. I like were the ROC puts my cheek when looking down. This setup is one fine piece of equipment!!! You can tell just by holding it that its built. I sold my eotech 553 with magnifier to get...

Does anyone know of a dealer who sells mounts and rings for an Anschutz match 64 rifle? I have tried Champion Shooter's Supply but the ring mounts they sell that mount on the 11mm rail that is part of the receiver are giving me trouble. My rifle is hitting about 4" low at 25 yards with the...

Just got a DPMS 308 and need a good mount to put the night force on, whats a good 1 peice 20MOA mount to put on these? The dealer down the rd has a Armalite for $139, is it any good and worth it do i need better? I need something that wont let the scope run out of elevation at 1,000 yrds. Thanks

I finally had a chance to mount my new scope- a Leupold Vari-X III 6.5x20 AO EFR on my Anschutz Match 64. I had ordered some Anschutz rings from Champion Shooter's Supply and installed them on my rifle's rail. I went to the range today and found that the point of impact was very low- about 8...

Hey I have a 30mm scope and want to put a red dot sight(already have the sight) I need to mount it somewhere. I was wondering what everyone else has done or if they have even done it at all? What mounts work and where can I get one?

I know its purpose is to have the optic sit further back on the rail, but this requires me to remove my rear site. Can the flip site still be functional in front of the acog?

I'm waiting on an MST-100 and base unit... Now, when I had my smith build my rifle he mountd the USO base on my Rem 700 - drilled and tapped for the larger screws... I gotta give him a call, they are not 6x48, but are 8x??? Wanna say 40... I'm hoping this will not be a problem, although I...

I am trying to decide the best path to go and wanted to turn to the experts. Looking to use a good mount on a flat top AR15 (5.56). Either a Larue type one piece or ARMS or Larue type two piece. Have also thought about getting some Badger or Mk4 rings and putting them on a QD rail mount but...

Any opinions on the Nightforce one piece mount? Are the pros and cons similar to the AI mount?

I'm looking for a optics/accessory mount that is actually mounted to the stock and bridges the barrel in front of the scope and was wondering if anybody knows if there is such a device and who makes/sells it?

I'm looking on possibly mounting a S&B 5-25 x 56 on a 300WM AIAW. Can I get enough elevation for 1500 yards out of a set of Badger Rings or will I have to utilize the AI Mount with 45* for the AI Picatinny Rail? Any help would be appreciated. Best, John~