problem

I finally had a chance to mount my new scope- a Leupold Vari-X III 6.5x20 AO EFR on my Anschutz Match 64. I had ordered some Anschutz rings from Champion Shooter's Supply and installed them on my rifle's rail. I went to the range today and found that the point of impact was very low- about 8...

I've got a magnum research .22/.17 and it stove pipes with all ammo I've tried!!! I'm about ready to get rid of the thing because I'm not gonna own a piece of shit rifle! I've tried almost all match and target ammo for semi auto rifles and it's driving me nuts. Any ideas??

So I was doing some shooting today with my Savage .308 verifying my zero and getting some dope from 10-100yds. While I was at it I went ahead and did a box test since I had never bothered to do that since I have owned the scope (USO SN-3 3.2-17x44 MPR reticle CM click values). My elevation...

I was putting a new grip (tangodown battlegrip) on my Colt 6920 when after I removed the grip screw, a small spring fell out along with a small gold colored pin, then my safety went kind of limp. How does this stuff go back together? thanks

I just bought a Trijicon MS01 (same as Docter red dot) and MS16 winged mount for my TA31RCO to make a TA31RCO-DOC. I should be able to do this with my eyes closed, but the MS01/MS16 won't fit on either my TA31RCO or TA01NSN - it's a little too long and rubs against the elevation dust cover. And...

So I just bought one these and I was finally able to go down to the range for break in. On my 5th shot, I noticed the bolt was very hard to close. I tried pushing it and it too a lot of force to close it. When I dropped the bolt (after much pushing), the rifle fired. It was a good thing I was...

I finally got a shellplate for my new Hornady Lock-N-Load AP. I have it setup and started to do my first loading on it. Having a minor problem. Every once in a while, the case (30-06) does not enter the case activated power die correctly and I dump some powder. It also results in the case mouth...

Phoenix Machine email contact link problem I saw a post on longrangehunting.com from a gentleman who had attempted to contact us and we had not responded to his request. Apparently our “email contact form” is not working properly so we have missed some requests. I will contact the web host...

I'm struggling to find a scope for my CZ 452 varmit> I want something that will be good out to 200 yards and I think I found somehting but I'm not sure. I'm looking at a Weaver V-16, but it only has 50 MOA of adjustment. I have the 20 moa base for my CZ, so I think that will get me out to 200...

I have had this on order for over TWO months. Every time I call I get some BS about "waiting for forgings". What a way to run a business, take your money and just string you out with promises. Anyone else getting this BS runaround?

I just bought a very nice 300WM and have noticed a peculiarity. When I fire factory ammo, the brass extracts and ejects without difficulty. When I shoot handloads through this gun (no signs of pressure on the cases, not shooting them hot, handloads are well within spec for case length and...

(Warning- this is lengthy. I'm putting in a lot of detail to help solve this problem) Well, at this point, I don't think there's a single 'hide member on here who hasn't already read through one of my f*&^% threads on this , but *just* in case, here are the previous ones before I delve in with...

finally put together another ar-10. it has a 21" complete noveske upper, and I assembled the lower. Took it out sunday. It shot sub 1/2 moa 5 shot groups, but it would not cycle. It would not load the next round into the chamber without pulling the charging handle back. I used 168 BH ammo. Any...

Hi Folks. I have a problem that maybe someone has the answer to. I have been reloading for about 8 Months now and I reload .308 in an M1A1 using both .308 and 7.62X51 Brass and 168 Sierra Match loads. I use the Dillon .308 gauge and check every round I reload. It shoots with no problems with...