I'm trying to be preemptive before summer really hits hard. My HVAC is dying a slow death, American Standard. Multiple companies have said same thing:
1) Needs to be 3.5 (company A) or even 4 ton (company B).
2) Return air is 16" and should be either 20" (company A) or 18" company B.
3) Add another register in kitchen/breakfast area
a) Company A wants to replace current 6" ducts with 7" and and another 7" with a 4x10 register.
b) Company B wants to keep 6" ducts and add a 6x12 register with 7" duct.
4) Company A sells Daiken, Company B (Bryant/Carrier).
5) Company A will add a MERV 15 filter system for 1500 more dollars, Company B, MERV 12 included at the air handler.
6) Company A puts 2 new drain pans in, one is an overflow. Not so company B.

Company A's cheapest price is 6K more than Company B. The most expensive from Company B which is full variable speed compressor and fan is only 400 bucks more than than the single stage variable fan from Company A.

Company B's price is more inline with quotes from 2.5 years ago (minus ductwork that nobody picked up on). Roughly $2k/ton. I grew up in a family business that did this type of work; but my father retired 25 years ago and has passed, so I'm completely out of the loop.

Daiken's warranty is unbeatable (12/12) and transferrable. However, I really don't want to be in this house more than 4 more years if at all possible. Is Daiken really 5K+1.5K more quality than Carrier?

I've got an AR15 with a White Oak Armament 18" SPR barrel with a cheap no name BCG from AIM Surplus. I've tried several ladders with it, but haven't had luck getting any decent groups. I've done a Varget ladder with 69gr SMK bullets, and a AA2520 ladder with 77gr SMK bullets, and most groups end up in the 1.5-2" area. Optic is a 3-15x SWFA. Could the bolt be having an issue on accuracy?

I don't believe this is me misdriving the gun. I feel like these are good trigger pulls. I have a large AR in 6.5 Creedmoor, which I shoot .75-1" with, and several bolt guns which shoot well under 1". Anyone have any suggestions for me?

Edit - More info:
My particular barrel is 1 7" twist rate. It's a stainless barrel, no flutes. It has a Geissele gas block on it that was pinned on by a gunsmith (ADCO in Ohio). They also coated the exterior of the barrel with a black coating.

The upper receiver is a blem BCM upper, with a thin coat of Loctite 620 retaining compound on the barrel extension to take up any space between the upper and the barrel extension.

Trigger is a Rock River Arms 2 stage trigger.

I do have some 55gr handloads that it shoots 1.25", and it shoots Fiocchi 55gr ammo around 1.4". I'd like to shoot heavier bullets though, and I believe this rifle can do better.

I tried some Gorilla 77gr 223 ammo (smk bullet) in it and it was a 3" group. I then shot the same load from my 223 Tikka Varmint, and it produced a .5" group.

Edit 2:
I took a borescope picture of my gas port. Could this be the source of my problem?

1 NightForce 3.5-15x50's $1025 per delivered. BOTH SOLD . Excellent condition, MOA knobs with MLR reticle. No trades, postal money order works best, I do not have any online payment systems

Hey y’all I had a quick question….. I switched my barreled action from an XLR to an MDT chassis and the accuracy has completely gone off. Now a little background the barrel has 2300 rounds of 6.5 Creedmoor on it and I did a heavy clean of the barrel. I then put 200 rounds through it and it still is not shooting the half MOA groups I was used to. Is it possible that I would have to bed an aluminum chassis? I also was able to borescope my rifle and did not see a carbon ring. The scope is tightened on rings as well to spec. Thanks for your help. Basically I’m wondering if my barrel hasn’t gone out could it be the chassis?

I keep my reloading gear, firearms, etc. all in my basement.

I run a dehumidifier during all the spring months, through fall until the humidity drops in the winter time.

My firearms don’t rust, but all of my dies are starting to get little patches of surface rust on them.

I’ve purchased the little pouches of desiccant (similar to what’s in a bag of beef jerky) and put a few in each die box, but I still get the oxidation.

Will coating my dies with a light coat of oil fix this?

Are there any other remedies that will work?

Everything still works as it should but it’s annoying as hell.

Login to view embedded media
"Your tail light is out"
"I want to see it"
"You're under arrest"
"Get out of the car" while being immobilized by tazer juice.
Then dragged out and beaten

Back the blue baby

This article is one of the best write ups I have seen to date explaining the many crimes of the "pandemic" engineers.


(Not sure if already posted elsewhere, I didn't see it when I searched.)

In the market for a gun/fire safe.Was wondering how many non optic guns are equal to one with optics in regards to space?

Catch and release for me, too many irons in the fire. I fired 15 rounds with a load I’d done for a previous 6 creed, was sub moa in this rifle with zero tuning. Building another rifle so need to fund that.

Barreled action done by Pederson Precision out of Argyle, WI.

ARC Archimedes SA
6mm Creedmoor
Bartlein M24, 7 twist, 24”, 5/8x24 thread
Cerakoted black barrel
128 round count

$1575 shipped

EDIT for clarity - BnA trigger not included

I have a brand new, legit (never owned by any .GOV), full power (full 45mW, not the limp-wristed 35mW domestic law enforcement model), full original factory kit L3 PEQ-15 in FDE.

Want to trade for a Swarovski 115mm Objective.

I have the 95mm BTX with Swaro Armor, so if you want to step down in magnification and trade your 115mm for my 95mm and maybe something else on my end, that would work too.

So besides Terminus and AI does anyone else make quick barrel change actions? thinking about down sizing to just one action with different caliber barrels. I know theres plenty of actions with ample pre-fit support but I would like something that allows me to make changes at the range without the need of a vise or wrench.

Thanks!

Edit: If you want the short answer...

I want to thank Josh and the folks at PVA for doing such an above and beyond amount of work to check this for me! In reality the problem was not theirs but another vendors.

Specifics on the resolution are here: PVA Tests EVERYTHING with results!

--------------------

Original post:

So!

I picked up a TBAC Ultra9 in 6.5.

My buddy @Baron23 Told me about the Area 419 Hellfire break / suppressor attachment system.

I went out and purchased a boat of their adapters and mounts so I can use them with the 5 suppressors I have in the pipe.

I installed the Hellfire mount on the barrel of my TRG-22, installed the 419 TBAC Ultra series mount on the supressor, and took the whole shebang to the range.

Without the TBAC installed, the rifle is dead on target.

When the suppressor was installed… the POI shifted 13 mils high and left.

WTF: I called TBAC and ask them what the think is happening… “You‘re getting baffel strikes, or at least the end-cap.”

I look, and sure as shit, there is a light copper trace inside the opening in the endcap!!!

Looking at the Area 419 TBAC CB mount I notice a very minor amount of blue loctite on the mating surface. That MUST be the issue!!!

Area 419, being awesome in general, sends me a replacement CB TBAC Mount just in case…

In the meanwhile, I install the TBAC CB Brake / supressor adapter, and test fire: no POI shift with the TBAC CB 30 cal brake / adapter. (No washer, per TBAC, I just screw it on the barrel to ensure everything works.)

I get the new 419 suppressor mount and install that.

Test firing the Area 419 Hellfire adapter setup with the new CB mount, THERE IS A 2 MIL TO THE LEFT AND HIGH POI SHIFT!

I put the CB brake back on and test fire, no POI shift.

Has anyone had weirdness with Area 419 Hellfire suppressor mounts?

Seems rounds are sliding on the inner surface of the end cap opening when using the Area 419 system.

What metric typically causes a load to shoot two distinct seperate but very tight groups? I'm sure it's a common issue in development. I'm thinking it's on the end of a charge weight node or the seating depth is right at minimum jump and bullet variation is putting it over ethe edge. Charge weight workup made this load appear like the good one but I'll admit I haven't had enough time to fine tune it. Might also try seating .010 deeper. Was in a rush to get ready for a match this weekend so it will have to do, but curious what direction to go afterwards. Thoughts?

Eta: It's not me, this rifle with other loads and my other rifles will shoot tiny 1 hole groups no problem.

Selling a brand new in opened box nightforce with 1 inch, 4 screw nightforce rings. I waited about 6 months to get it from nightforce but had a change of plans when it got here. Seriously awesome scope here!

Selling for $2350 with rings shipped

New old stock. Made before the ai molds got sloppy. I will post pictures when i can. $300 obo shipped. I dont really know what these are worth and feel free to offer me something

I am cleaning out my gun/reloading room. I have the following items for sale:

Add $5 for shipping.

- Widden Gunworks 6MM dasher FL Sizer: $40

In case anyone wants to see it live...

Atlas rocket going off from the Cape. This is one of the bigurns!!

Cheers,

Sirhr

I am offloading some scopes I don't use, looking to sell but open to trades.

First up is a Leupold VX3i 6.5-20x50 FFP TMR reticle. Asking $600 shipped TYD.
I have used this at the range a few times, never abused. Has some handling marks, though is perfectly functional. Comes with mount and flip caps.

Next is a Burris MTAC 4.5-14x42 SFP Ballistic Milling reticle. Asking $300 OBO shipped TYD.
This scope has maybe 20 rounds under it. Has some ring marks, otherwise in great shape.

Last is my Razor Gen2 4.5-27x56 EBR7c. Asking $1550 shipped. (LaRue mount not included).
Includes switch view and bubble level. Includes sunshade/stickers/papers that come with scope from Vortex.
I got this from another Hide member and now the circle of life must continue. Great scope, functionally flawless, though does have some scuffs/dings in the finish from use, some from me, some from previous owner.

Trades I'd be interested in:
Vudoo V22 BA, pref new.
ATACR 1-8, or 4-20 Milxt
ZCO or TT
Others?
(obviously we can discuss $$$ for trades with mismatched values)

Will accept PayPal F&F or you cover the fees, Postal Money Order, or Zelle.
"I'll take it" > "PM sent"
Thanks for looking
John

3 boxes of 500. $380 shipped each.

PayPal FF

You knew this was true

Hey guys, looking to do the spring cleaning and get out of the game for a bit as I have different work and life opportunities ahead of me that could use the money/focus right now. I may or may not do a gut on the reloading equipment and ammo this summer as well, so stay tuned!

Items are numbered in the picture below. I can get more detailed photos of a particular item if you are a serious buyer. Public "I'll take #x" trumps PMs and questions. Prices are shipped and I kept them low to account for the hassle of doing USPS money orders for payment. No e-payments please.

1) My pride and joy. Next Level billet lower, ALG trigger (not pictured), H2 buffer, B5 stock, factory Colt 14.5" pinned upper with added Daniel Defense free float quad rail, ambi-latch charging handle and QD foregrip included. Flip up sights not included - $1,200 shipped for just the rifle, $2,500 shipped with the Elcan Spectre DR 1/4

2) Next Level Armament build. BCM 10" mlok handguard, Rosco carbine length gas, 1:7, 11.5" barrel (for my fellow Michiganders, OAL is < 26" so good to go there), collapsible pistol brace, ALG trigger, Ambi safety, NLA Ambi charging handle (very similar to the new CMMG), Ergo slim grip. Includes rail covers. Flip up sights not included - $875 shipped, $300 additional for surefire and pressure switch, $350 for the MRO (accessories not for sale separately)

3) BCM factory 14.5" pinned lightweight upper. Comes with NLA ambi latch and an Anderson BCG. Will include the AFG on there as well. - $625 shipped - SPF to Beasler1

4) SDS Imports Duo-SYS 12 ga - SOLD

5) Unfired Custom built 308 lightweight shorty. Tuebor Legion Ti action, Proof 1:8 16.5" barreled threaded 5/8x24, Timney trigger, Screech Owl chassis, Ergo grip. Weighs 6.8lbs as the BA and chassis. Brake not included but will come with a thread cap - $3,100 shipped

6) Wilson Combat EDC X9 - SOLD

7) Lawton 8500 338 Norma Mag - SOLD

8) An ABSOLUTE BEAUTY! This is a Pre-64 Win 70 that is now chambered in 25-06. It was done by Williams in Davison, MI years ago. I bought it from the original owner and had intentions to use it as a whitetail rifle but it's too nice and a little hefty for a woods gun. I have the original 257 Roberts barrel for it as well. Stock was bedded for the new barrel. - $1,200 shipped or $2,000 shipped with the Leupold VX3, rings, and stock pack

9) Holosun HS503R - $190 shipped

10) APA Fat Bastard Gen 2 338 brake 3/4x24 threads. About 150 rounds through it but it's clean. - $130 shipped

11) ADM QD FDE 30mm mount. This was painted but I stripped 90% of it - $100 shipped

12) Crimson Trace 5-Series 3-24 with LR1 reticle (mil mil FFP). Comes with throw lever and nightforce UL rings - $900 shipped

13) Like new Elcan Spectre DR 1/4 with the 5.56 reticle I believe. All side illum. works great and I used this for several weeks straight and it held and returned to zero like a champ. Awesome optic. - $1,600 shipped - SPF to Beasler1

14) New Burris PEPR 30mm AR Mount - $65 shipped

15) Weaver 7x rangefinder. These were advertised as 1000 yard rangefinders when Weaver made them. I have hit 1000 no problem with it and up to 1400 on trucks and buildings. Great, reliable, rangefinder for cheap. Covered by Vista Outdoor's warranty even though they are discontinued is my understanding. - $180 shipped

16) Timney Mossberg ATR trigger. New in package. - $80 shipped

17) Original Rock River carbine free float quad rail. Comes with locking ring and barrel nut. - $50 shipped

18) Fostech Echo Sport Binary Trigger new in package - $200 shipped

19) GreyOps Arca Plate (I think maybe this was the Gen 1?) - $140 shipped

Selling NIB never used RRS Anvil 30
$395 Shipped conus
336-314-0044

No doubt, they will have a lot of fun!!

Photo courtesy: jstallings11