I have a DTA A-1 Covert chambered in 300 Whisper.

The barrel is a Benchmark 7 twist chambered by TS Customs.

Working up loads with Berger 215 Hybrids, Vhit N-110 and Lapua brass. S&B 5-25 and TBAC Magnus-SR.

I found a solid load going about 1065 with a single digit ES/SD. I played with seating depth a bit and found a depth that was about 5/8-3/4 MOA out to 300 yards which is a far as I was planning to go.

The first first shot at 300 goes about 2.3 mils low. The rest are fine. Nice little round group. If I let the rifle sit for 4-5 minutes, shot #1 again goes 2.3 mils low and the rest are back normal.

Seeing as how it is the first round on a "cool-ish" barrel that goes low and no others makes me think it is a gun issue and not an ammo issue.

I re-torqued all the barrel screws, checked the brake and can, scope mount, completely cleaned the barrel, etc. I even checked the loose nut behind the scope and had another solid shooter shoot 10 shots. 1st one low. 2-10 were normal.

I dont speak DTA that well, I am fluent in AI rifles.

What am I missing or not checking? Or am I just a dumbass?

Upper Only
Rainier Upper Receiver and Match Barrel
Wilson Combat Forearm
Surefire M951 (SUREFIRE LIGHT AND SWITCH ARE SOLD SOLD SOLD)
BCM Flashhider
SOLGW BCG

$400 shipped

Have this lying around without an action to put in it. Ran it with my Vudoo for a while and fed great. It has been cerakoted. Color is midnight metallic blue with slight copper accents around magwell. Previous owner stripped the grip screw but installed the MDT grip with 2 screws through the grip tang and it is as secure as the factory grip would be.

Comes with action screws and ambi bolt plug
MDT premier grip
extended brass nose

$600 shipped.

Western Nebraska, Eastern Wyoming, Colorado guys. Anyone looking to get into loading
I have an rcbs press, hornady powder thrower, rcbs electric scale, rcbs case trimmer, a priming tool, bunch of various hand tools, calipers, dies (223 308 338 some other stuff)
Small rifle primers around 1500
Large rifle primers around 2k
A bunch of various powder 10-12 lbs unopened a whole mess of stuff that's been used. Lots of 308 and 223 brass
A tumbler and media separator
175 308 bullets
69 gr 223 bullets
208 308 bullets
A bunch of 55gr 223 bullets
Everything you need to start a bench
1k for all of it
Magnum primers are not included they are going to a family member

So I have found myself at the point where I am in need of some good quality binoculars, but also need a rangefinder as well. So naturally I have been looking at the various rangefinding binos on the market, but have heard/seen too many complaints about image quality, and lowlight performance. My main question is should I go for a bino unit with LRF capability, or pick up some Vortex Razor UHD's (or some other comparable model with good glass quality) and a decent RF monocular? I understand that I could go for the alpha-tier offerings from Leica, Swaro, or Zeiss and not really have the issues I stated earlier.. but would rather not spend more than $1500. So here are the options I have looked into, would love to know what anyone's thoughts/experiences are. These are what I'm primarily interested in (but not limited to) these units:

Rangefinding Binos:
-Vortex Fury 5000 10x42
-Athlon Cronus UHD 10x50
-Burris Signature HD 10x42
-Meopta Optika LR 10x42
-Minox X-Range 10x42
-Steiner Predator 10x42
-Leica Geovid R 10x42

Anyone that has real experience with any of these, I would love to know what you think! Thanks luv u

​

More updates from Nazi raid on newspapers office and homes .

Looking to purchase my first suppressor. Plan on putting it on a 308 win and a 6.5 Creedmoor, both are bolt guns. Is direct mount the way to go or should I go with something with a quick mount? What’s everyone recommendation?

Selling my Like Brand Spanking New (Safe Queen) GA-Precision GAP-10 in 308 Caliber. This Rifle has only 50 rounds Total shot down the pipe and is all Black and Tactical AF. This is a Gen-1 version and hard to find, especially in Like New condition.

GAP-10 Gen-1 with HOGAN Receiver Groups
18" Heavy .875" Bartlein 1-11.25 Twist 5R Match Barrel.
Threaded 5/8x24" TPI for Suppressor with Thunder Beast 30CB Brake.
Seekins Precision Low Profile Adjustable Gas Block.
Geiselle SSA-E Match Trigger
Magpul PRS Stock
2 - PMags

Priced to sell at Only ***SOLD***

I have this priced Low for a Fast Sale as I found a Colt M16A1 machine-gun that I want to buy and need the extra cash to help fund the purchase. And these transferable Colt M16's are not cheap......




Login to view embedded media

Selling lightly used V3 AutoTrickler w/ AutoThrow and FX120i full setup. Runs great. No issues. Have all manuals and accessories.
$Sold shipped to CONUS.
***No Trades

Except when you were in the woods and kicked leaves over the turds.

hunted there X2 in the 70s. beautiful and sooooo different from my FL home state. reading on here guys saying that it is slowly being changed into a left coast state. looks like might be. here in FL conservatives are hanging on mostly. desantis is good and the legislature is at least not full woke. hope we can hang on but i'm worried about future things.

Seamaster Diver 300M Co-Axial Master

This is an absolutely beautiful watch. I love this watch and I will definitely get another in 38mm. I bought it from the original owner, who is a memeber here, just recently. I'm only selling it because it is just a little too big for my small wrist. It's a 42mm and I thought it would be good but my wrist are pretty small and I'm a slim guy so.... For any normal size wrist it would be great, it's not a huge watch, it's actually a great size and thickness .

Anyway, it's under warranty, as you can see I have the cards, box, ect.... everything including original receipt. The only blemish I can find is on the bottom of the clasp where all watches have some rubbing if they are worn for even one night. Otherwise it is spotless. This is a $5k watch and I got a good deal on it and just want to get my money back to get another one just like this in a 38mm.

Please let me know if you have any questions.

$3,600.00 shipped and FULLY insured.

These fucktards will dkeep it up until thre are no stores left, then bitch about discrimination because there are no stores in the area.

DC supermarket near closing after $500K in groceries walks ...​

Fox News
https://www.foxnews.com › giant-grocery-store-threaten.

Login to view embedded media
Login to view embedded media
Not a big fan of police if it ain't obvious.. but Condolences and prayers to the Camarena family. Nobody deserves to go like that. Bone tickling with icepicks...powerdrill to the brain..
This dude was heavily involved

Login to view embedded media
I won't do it... neither will he.

Tough night. Shit... 6 months. I do NOT want to carry him to the hole.

Cancer sucks. Fuck cancer.

Sirhr

I've been instructed to move my questions to another thread so here it is..

@Gingerman You stated that you have a business of building complete Upper Receiver groups. I would be most interested in hearing about your assembly process.

Century Arms FA MAS 5.56 . During the late 1980s, Century Arms imported a very small number of semi-automatic FA MAS's into the United States. This one just sold for $58,525 on GunBroker.

Skittles are out. Those fuckers are woke.

Any suggestions for some new morale boosters from a company that doesn’t hate us?

If whites were doing this shit they'd be thrown in jail.

Login to view embedded media

The last thread I started turned into a soap opera (albeit entertaining) I'd like to avoid that this time around

Before I bought the Cronus, while shopping around, I never gave the XTRIII any serious consideration. The XTRIII looks really nice, but the reticle seems very convoluted and hard to read (I perfer easy-to-read .2 markings) ,other scopes in this price range have better glass, and I've never heard anyone say "damn those Burris turrets are incredibleeee" so....

...if it doesn't have the best glass
...or turrets
...or reticle
...or FOV
...doesn't parallax down to 10 yards
...the elevation is 90 MOA vs. 110 MOA in comparitive scopes

I mean this very sisncerely (no drama allowed lol)....what am I missing??

-Kevin

For sale:

Chambered 300 blackout. M24 proof Contour barrel. Remington 700 action trued. Heavy recoil lug. Triggertech trigger. Linear compensator. Action cerakoted. All work done by Baldwin Gun Works.

Scope not included.
Brace not included. But can be negotiated separately.

Used for Illinois deer season, but switching to rifle now. Shoots same hole at 100 yards.

Asking $1500 obo shipped to your FFL. No trades at this time unless you have a Christensen Arms Ridgeline Scout in 300 BO

*** Traded ***

I have a Manners TCS with Gen 1 ( Area 419 ) ARCA Rail. It has 4 internal weights. I have all the spacers and rear weight to go with it as well. Color is Altus Badlands I believe. Price is $1500 Shipped net to me.

Trades.

Manners PRS1 Rem 700
Manners PRS2 Rem 700
*** ARCA Rail and 1.25 barrel channel is a plus ***
*** Black, USA or Blood color would be awesome ***
Vortex Gen 3 plus boot from me

In the shittiest shit hole in my ever shittier state (though I’m in rural farm county and love it !) Detroit PD has been using a very Shitty AI facial recognition program to identify criminals, because they are absolutely useless in solving crimes - like when they had 11,000 untested rape kits in a storage unit that had homeless living in it and stealing evidence from it . Anyhow the relatively new program has already resulted in 3 federal lawsuits and to date hasn’t actually solved a crime or identified the correct person. But not ones to give up easily on a terrible idea and being fresh out of fresh ideas it’s still being used . Resulting in an 8month pregnant lady - with no tattoos being identified as a Jack jacker and armed robber . And maybe there are several hugely pregnant armed robbers but this particular armed robber they were looking for had lots of tattoos and wasn’t obviously extremely pregnant. But not being easily deterred while preforming the people’s business they proceed with the arrest and all charges were later dropped because of lack of evidence and a new federal lawsuit was filed on Aug 8th.

The only comment this far from DPD “we were just doin hour job and arrested who the machine told us to arrest “.

All three were done by the best in the business, Southern Precision Rifles (Bugholes). All are brand new with 0 rounds on them. All 3 are the longer lasting 400MODBB material.

1. 27" 6 Dasher. Bartlein 400MODBB straight profile. 1:7.5 twist. 5/8 threaded muzzle. Brake NOT included. $1050 $785 shipped CONUS.

2. 18" 6.5PRC. #13 contour (Rem Varmint/Sendero) Bartlein Carbon Fiber 400MODBB. 1:7.5 twist. Stainless areas DLC coated. 5/8 threaded muzzle. APA muzzle brake. $sold shipped.

3. 16" 308Win. #13 contour (Rem Varmint/Sendero) Bartlein Carbon Fiber 400MODBB. 1:10 twist. Stainless areas DLC coated. Sold shipped CONUS.

Have well over what I'm asking into all three of these so prices are firm.