rail

I want to avoid scratching my scope with scope rings, so am considering the Burris Signature with plastic insert. These appear to be a Weaver type, whereas the top of my AR15 is a Picatinny rail. Besides there being no spec for slot spacing on the Weaver, the slots on the Weaver are .180" wide...

I'v recently bought a HS HTR camo green... I would like to mount a Badger scope rail, fit normally ? Or I've to do modifications ? thanks

What should I consider to determine the "MOA" of a rail mount and height of rings. Barrel is heavy contour and the bell of the scope is 40mm. Thanks.

Does anyone have pics of the the rail system US Optics makes for the M40A3 Rifle, or where I could find some? They have one on the site but it's kinda crude

While on the topic of TRP Operators...Can anyone point me in the direction for a holster to fit mine...It has the full length rail. Any help would be appreciated. Thanks Billy C

I just purchased a TC Bench Mark in .22LR I want to set it up with a night vision weapon sight to care of some coyotes near the house. The rifle came with two short Weaver rail mounts screwed into the top. Will a regular Weaver rail (6" long) screw into it or do I need a special rail? I did...

Tools/Supplies Drill 3/4 bit of some sort, I used a 3/4 HS Counterbore with #21 drill bit as a pilot 1/4 inch drill bit Tape Not pctured, glue Allen wrenches BT17 Rail from our own Kasey BT1517 fastener set from Kasey And of course the Atlas Bipod I removed the bipod stud that McM...

Been searching here and there for a pre-drilled rail to mount an Atlas bipod on my 10fp. Without much luck. Factory tupperware stock with the swivel studs at 2.5 inch on center. OH and BTW where can one find Swivel Studs in various sizes and lengths? Looks like I need to just buy some raw...

Looking to get some rail covers for my YHM forend. What are your favorite or do you run a combination?

anyone know the length difference between the short action and the long action 20 MOA rail?

Just ordered a rail from HotRodd9mm for a CZ. He said the rail was"iffy" fitting a Sako FinnFire, might fit, might not. Who does make a 20moa rail for a FinnFire? thanks, Keith

My neighbor came over Sunday with a brand new CZ 550 and a 20 MOA rail from US Optics. I am not familiar with these rifles at all, fact is this was the first time that I've got my hands on one. It has a dove tail action similar to a Sako. I need some input on mounting this rail. Is it necessary...

Need some advice. Leupold VXIII LR 6.5x20x40, Leupy 1 pc std base, std low rings all on my 700 VS SF. Within the last 2-3 in lbs of torgue the adjustment housing makes very slight contact with the rail, before that there is 1/32"-1/64" clearance. Is this a bad situation? Do I need to remove a...

I went through Badger's online instructions, and just want to verify: <ul style="list-style-type: disc">Clean base and top of 700 receiver (and screw holes) with solvent (is 90% Isopropyl alcohol OK?)Put red loctite on bottom of baseMount rail on receiver, check that all screws don't bottom...

Hi guys, I have the McCann MIRS rail for the Rem700 action SA and a Leupold 4.5-14x50mm with the ARD + flip up cover. The issue I have however is my Leupold MK4 Medium rings were too low, they have a High and Super High MK4 ring set. Does anyone have any experience with the MIRS and know their...

I have a Savage Model 12, short action, with a round receiver. It has a stainless barrel and i would like to put a silver or stainless scope rail on top if it. All i can seem to find are black rails or normal bases that are silver. Please let me know if you know where i can find this. Thank you.

Hey guys, Although I am not new to guns by any means, I am to bolt actions and optics. I recently picked up a Sig STR 970 and someone recommended me getting a 20 MOA rail for it. I know what it is, but what exactly does it do? I am sure alot of you are laughing at this, and well, if I knew the...

I am ordering a AA 6.5 Grendel 19.5 and am going to top it off with a leupold mark4 4.5-14x50. I would like to be able to reach out to 600-800 yards with this setup. Should I have a rail with some form of MOA built into it or not??? Also, what would be a good ring selection for this application...

I'm looking on possibly mounting a S&B 5-25 x 56 on a 300WM AIAW. Can I get enough elevation for 1500 yards out of a set of Badger Rings or will I have to utilize the AI Mount with 45* for the AI Picatinny Rail? Any help would be appreciated. Best, John~

I just bought one of the M40A3 rails from CDIPRECISION and I was wondering if anyone can recommend someone to cut the receiver and drill and tap the holes to 8/40. Thanks Josh