screw

Shows 2 ball bearing screws used to tighten the movement of the stock to minimum. They indeed work well.

hey i just got a rem 700 p,one of the base screw holes is stripped out.should i retap it with the same size and see if it takes.or go one size larger and be done with it.also if anyone knows the screw/bolt size please share so i can get the tap and bit ordered.

At one time, Seekins was planning to build more 6 screw rings. Id like a matched pair, one 4 screw and 1 6 screw. Anyone know what became of this?

What purpose does the front ADL trigger guard screw serve (i.e., the BDL only has 2 action screws)? Is it's purpose only to hold the mag box in place and to more firmly secure the trigger guard? Is there any inherent loss in accuracy if the front screw is not used? The reason that I ask is...

I have a stripped base screw on my savage BTVS that I cant get out. What tools do I need to get it out or does anyone have any advice. Thanks a ton.

..as well as the next guy. Went to the range today and fired three rounds from 1K. The first two were solid hits 8" apart and then I pulled(called) the third shot. Overall the 3 shot group measured 11 1/2". Not too bad/ not too good. Back to the range for more practice.

Does anyone know what the screw thread size is for this receiver? Are they mostly standardized on most rifles? I want to chase the threads in the receiver with a tap, but I'd prefer to start with the right size from the get-go. Edit: Nevermind, found out. 8-40

Is the head on the screw that holds in an aftermarket front sight on a Glock 3mm or 3/16"? Thanks.

Does anyone know what thread size the action screws are on a rem 700?

This is an awesome torque screw driver. Especially for 10/22's and scope rings http://takdriver.com/viewtopic.php?f=6&t=45

Wondering if AICS requires special action bolts to screw down action to the chassis or can you use factory remington action screws to tiighten the action down on an AICS 1.5 or 2.0????....Any help is greatly appreciated....Also..I hear you dont have to bed an AICS chassis...just drop it right...

did Glen stop making these?

I took my 10/22 to the range the other day and it was shooting very poorly and not holding zero. i thought it was a fauly scope and wanted to change to a different scope so i went to change it out last night, i found my issue. both of my rear base mounting holes are stipped, looking for some...

OK so I got a little carried away with the dremel tool and need some advice. I dug a small crater like spot on the composite part of my HS stock. I dont think this will be a big deal but wanted to make sure. Is there something I need to do to fix this before I bed it with devcon??? Pics are not...

I purchased a new Badger M5 from another member who never installed it. I noticed when I tried to mount it that the rear torx bolt was way too long (2"). The front one fits fine. I am fairly confident that these were the ones that originally came from Badger. Could it be just a mix up or am I...

I bought a PTG bolt and had the bolt handl tigged on. This week I took the action and trued it using the PtG kit and reamed the raceway. Everything went okay and I got done chambering and assembling the rifle a day or so ago. Today I finally got around to shooting it. About round 16 the bolt...

Does Seekins still sell the 6 screw/4 screw combo ring set? Early last year I topped a .308 KMW with a combination set where the 6 screw was forward and the 4 screw aft of the elevation adjustment. This setup rocked and I'm hoping I can replicate that on an upcoming 260 AI rifle topped with...

I was just trying to pull some of those little junk screws remington blocks off the scope mounting screws with. The little bugger just spins and spins and did I mention spins without coming up enough for me to grab it at all. I have had several of those little screws do this in the past but...

I'm changing the stock on my Remington 700 to a H&S stock. With the new stock the front action screw will only screw several threads in to the action. I don't want to pull the threads so where can I get a slightly longer front action screw? I could also counter sink the base plate a little? Any...

After adjusting the trigger weight adjustment screw on a Remington trigger(in my case an XMark)what are some locking compounds that can be used on that screw? It has been mentioned here in other posts to use nail polish. Are they talking about the bright red crap that my wife has in her cosmetic...