base

I finally got my 1-piece base machined. I wouldn't actually say it was finished since I still need to put a finish on it. It took me 2 tries on making it. The the double angle tool I ground was oversized and forgot to compensate for it. So the first one's rails were not to spec. I...

hey guys, here is the deal. i have a leupold mk4 4.5x14, in badger medium rings, sitting on a badger 20moa base. the problem is i cant get the scope far back enough to achieve proper eye relief. i am pretty handy with a dremel tool and file so can anyone give me a good reason not to cut a small...

I have a Remington SPS V I will be using a SS 10X scope with. I have Leupold MK4 30mm steel rings. My question is what base would you recommend for this set up, I am looking at MK4 bases but am looking for opinions.

I just bought a Kahles Helia cl multi zero 3-10x50 w/ side focus for my new rifle. w/ 1" tube. I am going to put on the new Savage 10 fp precision carbine w/ the new accustock w/ digital camo in 308 winchester, w/ removable magazine, that comes out at the end of april. I am having a hard...

Well, I went to mount a scope to my Remington 700 today and I used the indicating rods to check the alignment of the two piece Leupold base and rings. I dialed in the "windage" but realized that the rear rod was much lower than the front. So I clamped a 1" rod in the rings and isolated the...

I have a 700 action that has no alphabetic prefix. When I put a Picatinny or Leupold one-piece base on it, the base flexes. It does not make contact with the front of the receiver when I tighten the rear base. I am making the assumption that this is one of the actions that needs a base...

what base is a bolt on for a cmp 40x b i tried to put a badger on it but it has alot of clearance up under the back. i think i read somewhere that the back area was cut a little diffrent on some older actions.

Let me start off by saying that I do not have a lot of experience when it comes to bedding, I learned how to bed a rifle by looking at Randys (HateCA) DIY page and by asking him a billion questions via e-mail (which he was more than willing to answer) I have since bedded 3 rifles, 2 bottom...

I've bought a Nightforce 12-42X56 Benchrest scope for my new 6.5x47 Lapua F-Class gun. Scope spec'd for 40 MOA elevation range. I'll need about 29 MOA to get to to 1K with a Berger 130 from a 100Y zero. Gun still being built and will have 20 MOA tapered base installed. Just for grins , I...

so what are some bases that the seekins rings work well with? will they fit the us optics base? I have a PRI base that seems to be just a bit too wide for them. Any recommendations? looking at 0 MOA bases. thanks

Are the lugs on the bases that lock into the open area of the receiver a necessity for the heavy scopes or is it a belt and suspenders approach? Im going to be running the 8x40 screws and have been bedding the last few bases in steel bed to begin with. I have been a fan of the DNZ mounts on the...

I just got in my scope base and it is a 20 MOA base but I have never had a base like this before can anyone tell me does the thick end of the base go to the back or the front thank you

I hate to start a new thread as I am sure it has been covered I cannot find it however. What is the advantage to a one piece base instead of a two piece base setup? I am looking at mounting a scope on my new 5r 300 Win mag and dont want to go the wrong way and waste money. Lots of people seem to...

Is anyone here using a tapered base for a Remington 541. Currently my rifle is zeroed at 50yds which is also my max elevation. I have a ton of down but no more up and am thinking that an elevated base would get me where I need to be. thanks in advance dgwelsh

I'm struggling to find a scope for my CZ 452 varmit> I want something that will be good out to 200 yards and I think I found somehting but I'm not sure. I'm looking at a Weaver V-16, but it only has 50 MOA of adjustment. I have the 20 moa base for my CZ, so I think that will get me out to 200...

Do any of you guys know for certain if the Leupold QRW or PRW rings would fit on a Picatinny rail? Long story why I ask, but it basically involves giving me some flexibility to swap scopes between rifles.

Guys I just got a scope base for my H&R M12. Some of you shoot M12's so you might be interested. I got one from Ken Viani 8928 N. McVicker Morton Grove, IL 60053 you can see one and also get the email from this link: http://personal.swayzee.com/jayb/Viani/ they run $90 and also...

rifle is Remington 700 SPS .308 Tactical Scope is Tasco SuperSniper 10X42 I'm looking at Ken Farrell rings and base but don't exactly know what models i should purchase for my particular gun. Also, can anyone here talk me into something less expensive with equal quality? Help a noob out

I recently purchased a Remington LTR from a forum member with a preinstalled Badger base. Is there any way to determine if it is a 20 MOA base or just standard. I'm new to precision shooting and not familiar with bases in general. Thanks.

ok, so I got a uso 20moa rail to replace my two piece mounts... for long action 700. the website says it comes with several different length screws... I got 6 in the bag, only need 4, but they are all the same length, which is WAY too fucking long. They stick clear through into the lug...