• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Search results

Search the forum Search Articles
  1. TN-MadDog

    Bourbon What have you tried lately

    I haven't seen a good bourbon thread in a while so I thought I would start a new one instead of reviving an old one. I'm no expert and rarely buy anything real expensive but I do like bourbon and like to try new things. None of the local shops have a lot of variety and I get tired of the same...
  2. TN-MadDog

    photo's not showing up on Kindle

    May just be an issue with our Kindle that occasionally use. Some photo's display normally, others I just get a small square with a question mark. Any ideas on what is causing that? I've tried everything I could think of. Thanks
  3. TN-MadDog

    MagnetoSpeed users, please check my set up

    I bought a MagnetoSpeed V2 and hope to use it this week. I have been looking it over and getting it set up. Hoping some of you that have been using it would give your opinion of the spacing from the bore. I used a couple different spacers and this looked the best to me but not sure if it is...
  4. TN-MadDog

    CZ 455 Precision Trainer scope ring question-done

    I have a CZ 455 Varmint Precision Trainer on order and have a question for anyone that has one. The scope that I am going to use has a 30mm tube and a 50mm objective. I have a DIP 25 MOA extended rail on order to go with it. What I don't have and need to order is a set of scope rings. I'm...
  5. TN-MadDog

    Storing hard cases in attic?

    I'm trying to clean out my gun room and a closet to make room for even more junk. I have accumulated several plastic hard cases that I don't use. I thought about selling them but I'm sure I will eventually need them. I was thinking about storing them in the attic long term. Do you think the...
  6. TN-MadDog

    Awe S*%t moment.

    Was priming some new brass on my Forster Co-ax press. Must have caught the edge on a piece of brass and got a sliver down in the priming mechanism. I didn't notice that it was putting a crease in the primers until I had primed eight more pieces. Kinda shocked me that it made that big of a mark...
  7. TN-MadDog

    Gunsmithing Flush cups in a wood stock?

    I would like to install one of these multi adaper kits from Triad in a wood stock. I want to be able to have a stud for a bipod and also be able to remove the stud when shooting on a rest. It is rimfire rifle with a fairly heavy stock. I have seen a couple of posts here showing how to...
  8. TN-MadDog

    Photos Little something came in the mail today

    My sister sent me this for my 50th birthday. Having a little sample right now. Need a good cigar to go with it.
  9. TN-MadDog

    Three Thumler's tumbler questions.

    I just got my Thumblers tumbler and had a few questions. I'm going to be using it with the SS media with water/soap/Lemi shine. 1. the drum is a little out of square/round (however you want to say it). As it is turning on the stand, it is wobbling about 1/2" side to side. Not sure if it is...
  10. TN-MadDog

    Gunsmithing Rust prevention on unfinished receiver?

    I picked up a receiver last week for future build. I got it out today to look it over and it had a small amount of rust on it. Mostly inside the bolt body and a very small amount on the receiver body. It did not appear to have any type of rust protection on it. It will be several months before...
  11. TN-MadDog

    A little too much pressure?

    I'm just getting into reloading for precision rifles. I have loaded off and on for a long time for rifle and pistol but have been out of it for several years. I am trying to work up loads for my GAP Crusader. Once fired Lapua brass neck sized only. 175gr SMKs Loaded .005 off the lands Varget...
  12. TN-MadDog

    Gunsmithing ? about ordering a stock

    Not sure if this is the correct place to post this question, but I hope to get an answer from the folks that work on them. I am going to order an A5 stock and was not sure about the aluminum pillars. Should I have McMillan install them or wait and let the smith that does the work install them...
  13. TN-MadDog

    Gunsmithing Oversize recoil lug

    I am planning to purchase a Surgeon RSR during the group buy that is starting today. One of the options is a .354" lug instead of the standard .25" lug. Other than the extra $44 is there any downside to it? Would you consider it worth the extra $$s? I have not decided for sure what the...
  14. TN-MadDog

    Gunsmithing Chamber casting Updated with pics

    Hey guys, I could use some help learning how to cast a chamber. I want to make a chamber cast of a AR upper chambered in 300 Whisper. I have read all that I could find about the process but I still have some questions. The main issue that I am concerned about is figuring a way to to get "just...
Top Bottom
Back
Home
Forums
Merch
Alerts